TA4600 TA4320 TA2300 TA2160
TA4600 TA4320 TA2300 TA2160 TA4600 TA4320 TA2300 TA2160
INTRODUCTIONI. DescriptionThis device is a high power, audio amplifier. Use it responsibly. Veryloud music can cause permanent hearing loss. This amplifier is intendedfor installation in vehicles with a 12-Volt, negative ground electricalsystem. Attempting to connect or operate the amplifier in another type ofelectrical system may cause damage to the amplifier or the electricalsystem.II. About This ManualRead the Instructions-Be sure that you have read all operating instructions and understand allsafety precautions before installing and operating the amplifier. Werecommend that you have your TA series amplifier installed by aspecialist.Follow the Instructions-The instructions are intended to help you safely obtain the bestperformance from the amplifier. Carefully follow all installation andoperating instructions.Save the Operating Manual-Keep the manual in a safe place after installing the amplifier. You mayhave questions later.Text Conventions used in this Manual-Bold-Headings and important information.Bold, Underlined-Very important information."Bold"-As labeled on the amplifier, or quoted from elsewhere in thismanual.III. Safety and Operating Precautions-Caution!This symbol warns the user of a potential risk or hazard if instructionsare not followed.⇒ This arrow symbol points to a specific instruction for avoiding apotential hazard.ii
1. Installation1.1 Installation- Mounting the AmplifierStep 1- Disconnect the negative (-) battery cable before mounting theamplifier or making any connections. Check the battery and alternatorground (-) connections. Make sure they are properly connected and free ofcorrosionStep 2- Choose a mounting location for your amplifier. Find a location ona flat surface away from heat and moisture. Be sure the mounting locationand the drilling of pilot holes for mounting will not present a hazard to anywires, control cables, fuel lines, fuel tanks, hydraulic lines, or other vehiclesystems or components. Common mounting locations are under the frontpassenger seat, or in the trunk area. Choose a location with unimpaired aircirculation. The amplifier will dissipate heat more efficiently if mountedvertically.Step 3- Use the supplied screws. Place the amplifier in the mountinglocation, and mark the positions of the holes with a marker, pen or pencil.Carefully drill the mounting holes in the marked positions.Caution!⇒ Check carefully before drilling any pilot holes.Step 4- Use the supplied mounting screws to securely fasten the amplifierto the mounting surface.1.2 Installation- Power ConnectionsStep 1- Run a power cable from the battery to the amplifier mountinglocation. Use rubber grommets to protect the cable anywhere it has to gothrough metal.TA4600, TA4320, TA2300 - Use #8 AWG or larger powerand ground cable.TA2160 - Use #10 AWG or larger power and ground cable.Step 2- Connect one end of an in-line fuse holder to the power cable.Connect the other end of the fuse holder to the positive battery post with 20cm (or less) of the same cable. This fuse location will protect the systemand the vehicle against the possibility of a short circuit in the power cable.Be sure to use a fuse and fuse holder adequate for the application. Do notplace a fuse in the holder at this time.The maximum fuse rating for each amplifier in the TA series is:TA4600 - 2 X 30 Amp TA4320 -40 AmpTA2300 - 30 Amp TA2160 - 20 Amp1
- Page 1: MOBILE POWER AMPLIFIERSTA46004 X 15
- Page 5 and 6: SPEAKER TERMINALSFollow the (A/B/C/
- Page 7 and 8: 2+1 MODE WIRING DIAGRAM-Use 100 Vol
- Page 9 and 10: 2.2 Operation- Built-in CrossoversC
- Page 11 and 12: TA2300, TA21601. RCA input jacks 2.
- Page 13 and 14: Troubleshooting:Condition Possible
- Page 15 and 16: 1. Installation1.1 Installation- Mo
- Page 17 and 18: BORNES AV ET AR DES HAUT-PARLEURSSu
- Page 19 and 20: MODE 2+1, DIAGRAMME DE CÂBLAGEBran
- Page 21 and 22: FUSE15A15AX-OVERLPF- FULL- HPFLPF40
- Page 23 and 24: 4. Bornes d’alimentation 5. Fusib
- Page 25 and 26: DépannageProblème Cause possible
- Page 27 and 28: ⇒ Dieses Pfeilsymbol weist auf ei
- Page 29 and 30: Masseanschluss ab. Bei jedem Verst
- Page 31 and 32: SERIES CONNECTION USING 4 OHM SPEAK
- Page 33 and 34: Schwarz: Hochpegel-Eingang MasseKei
- Page 35 and 36: ersetzt wird. Ersetzen Sie immer mi
- Page 37 and 38: Merkmale und technische DatenTA4600
- Page 39 and 40: INTRODUCCIÓNI. DescripciónEste di
- Page 41 and 42: de los cables de alimentación y de
- Page 43 and 44: 1.4 Instalación- Autoderivación,
- Page 45 and 46: HIGH LEVEL4 CanalesCable blanco Can
- Page 47 and 48: PROTECCIÓN CON FUSIBLES- Un fusibl
- Page 49 and 50: RMS/Maxpotencia eficaz,2Ω,THD
INTRODUCTIONI. DescriptionThis device is a high power, audio amplifier. Use it responsibly. Veryloud music can cause permanent hearing loss. This amplifier is intendedfor installation in vehicles with a 12-Volt, negative ground electricalsystem. Attempting to connect or operate the amplifier in another type ofelectrical system may cause damage to the amplifier or the electricalsystem.II. About This ManualRead the Instructions-Be sure that you have read all operating instructions and understand allsafety precautions before installing and operating the amplifier. Werecommend that you have your TA series amplifier installed by aspecialist.Follow the Instructions-The instructions are intended to help you safely obtain the bestperformance from the amplifier. Carefully follow all installation andoperating instructions.Save the Operating Manual-Keep the manual in a safe place after installing the amplifier. You mayhave questions later.Text Conventions used in this Manual-Bold-Headings and important information.Bold, Underlined-Very important information."Bold"-As labeled on the amplifier, or quoted from elsewhere in thismanual.III. Safety and Operating Precautions-Caution!This symbol warns the user of a potential risk or hazard if instructionsare not followed.⇒ This arrow symbol points to a specific instruction for avoiding apotential hazard.ii
Change language