HT STAGE 100 HT STAGE 60 - Blackstar Amplification
HT STAGE 100 HT STAGE 60 - Blackstar Amplification HT STAGE 100 HT STAGE 60 - Blackstar Amplification
English5. Speaker Emulated OutputThis output emulates the tonal characteristics of a guitar speaker cabinet andprovides a natural valve overdrive tone for connection to a recording device ormixing desk. Always use a good quality screened lead.NOTE: To ‘silently’ record, turn the amp to standby mode. You may also recordfrom this output while in standby mode without a loudspeaker connected, butensure that no loudspeaker leads are connected to any of the loudspeaker outputjack sockets of the amplifier, as this will defeat the load protection circuit and causedamage to the amplifier.6. Cabinet SwitchThe switch enables you to select either a 4x12 closed back or a 1x12 open backcabinet emulation for the Speaker Emulated Output.Technical SpecificationHT Stage 60Power (RMS): 60 wattsValves: 2 x EL34, 2 x ECC83, 1 x ECC82Weight (kg): 30.3Dimensions (mm): 715 x 586 x 278Footswitch: FS-7 included, optional FS-4 for Overdrive 2 VoiceEnglish7. Reverb Dark/LightIn the out position the digital reverb is voiced to have a warm dark quality. Whenthe Light position is selected the reverb has a brighter quality with more zing on thereverb tail.HT Stage 100Power (RMS): 100 wattsValves: 4 x EL34, 2 x ECC83, 1 x ECC828. Effects Loop ReturnConnect the (mono) output of an external effects unit here.Weight (kg): 21.3Dimensions (mm): 670 x 313 x 2639. Effects Loop SendConnect the (mono) input of an external effects unit here.Footswitch: FS-7 included, optional FS-4 for Overdrive 2 Voice.10. Effects Loop LevelThe Effects Loop Level switch sets the effects loop to either +4dBV/-10dBV, whichenables you to use it with either professional equipment (+4dBV setting), or withguitar level effects such as effects pedals (-10dBV setting).11. Overdrive 2 Voice FootswitchAn optional 1-way latching footswitch (Blackstar FS-4 recommended) may beconnected here to allow the Overdrive 2 Voice function to be remotely controlled.12. FootswitchThe supplied footswitch is connected here. The footswitch enables you to switchbetween Clean, Overdrive 1 and Overdrive 2, and Reverb on/off.1213
- Page 8: EnglishFront PanelClean Channel1. I
- Page 14: Wichtige Informationen zur Sicherhe
- Page 18: VorderseiteClean-Kanal1. InputHier
- Page 22: den internen Lautsprecher des HT St
- Page 26: IntroductionCaractéristiquesMerci
- Page 30: FrançaisÉgaliseurs Overdrive 1 et
- Page 34: ¡AVISO!Importante Información de
- Page 38: Panel frontalClean Channel1. Entrad
- Page 42: Salida ‘1x16 Salidas ‘1x8 Ohm S
- Page 46: 4746JapaneseJapanese
- Page 50: 5150JapaneseJapaneseUSAUK
- Page 54: HT Stage 60 Front PanelEnglishINPUT
English5. Speaker Emulated OutputThis output emulates the tonal characteristics of a guitar speaker cabinet andprovides a natural valve overdrive tone for connection to a recording device ormixing desk. Always use a good quality screened lead.NOTE: To ‘silently’ record, turn the amp to standby mode. You may also recordfrom this output while in standby mode without a loudspeaker connected, butensure that no loudspeaker leads are connected to any of the loudspeaker outputjack sockets of the amplifier, as this will defeat the load protection circuit and causedamage to the amplifier.6. Cabinet SwitchThe switch enables you to select either a 4x12 closed back or a 1x12 open backcabinet emulation for the Speaker Emulated Output.Technical Specification<strong>HT</strong> Stage <strong>60</strong>Power (RMS): <strong>60</strong> wattsValves: 2 x EL34, 2 x ECC83, 1 x ECC82Weight (kg): 30.3Dimensions (mm): 715 x 586 x 278Footswitch: FS-7 included, optional FS-4 for Overdrive 2 VoiceEnglish7. Reverb Dark/LightIn the out position the digital reverb is voiced to have a warm dark quality. Whenthe Light position is selected the reverb has a brighter quality with more zing on thereverb tail.<strong>HT</strong> Stage <strong>100</strong>Power (RMS): <strong>100</strong> wattsValves: 4 x EL34, 2 x ECC83, 1 x ECC828. Effects Loop ReturnConnect the (mono) output of an external effects unit here.Weight (kg): 21.3Dimensions (mm): 670 x 313 x 2639. Effects Loop SendConnect the (mono) input of an external effects unit here.Footswitch: FS-7 included, optional FS-4 for Overdrive 2 Voice.10. Effects Loop LevelThe Effects Loop Level switch sets the effects loop to either +4dBV/-10dBV, whichenables you to use it with either professional equipment (+4dBV setting), or withguitar level effects such as effects pedals (-10dBV setting).11. Overdrive 2 Voice FootswitchAn optional 1-way latching footswitch (<strong>Blackstar</strong> FS-4 recommended) may beconnected here to allow the Overdrive 2 Voice function to be remotely controlled.12. FootswitchThe supplied footswitch is connected here. The footswitch enables you to switchbetween Clean, Overdrive 1 and Overdrive 2, and Reverb on/off.1213