Submersible Sump Pumps Pompes submersibles pour ... - Flotec

More documents

Recommendations

Info

Operation / Repair Parts 6 Discharge Pipe Basement Floor Lift Sump Pit Check Valve (Install Vertically) Figure 12 – LIFT: Lift is the vertical distance the pump actually lifts water.The higher the lift, the lower the flow. NOTE: The friction caused by water running through the pipe will also, on longer pipe runs, reduce the flow. PARTS BREAKDOWN 1 2 3 4 Key No. Part Description Qty. 1 Power Cord Assembly 1 PW17-281 2 Bracket 1 PS19-102 3 IntelliShield Switch Ass’y 1 PS17-1560 4 Impeller† 1 PS5-22P NOTE: If motor fails, replace entire pump. † See Page 8 for impeller replacement instructions. 5947 0209 For parts or assistance, call Flotec Customer Service at 1-800-365-6832
Performance / Troubleshooting 7 PERFORMANCE GPH AT TOTAL FEET OF LIFT (See Figure 12) Model 5 ft. 10 ft. 15 ft. 20 ft. CAPACITY GALLONS/HOUR No flow at height shown below FPSC5000A 4,700 4,100 3,500 2,820 29’ ELECTRICAL & SWITCH SPECIFICATIONS Individual *Switch Setting Motor Branch in inches Motor Full Load Circuit Water Level For: Model HP Amps Req.(Amps) On Off FPSC5000A 3/4 7.0 15 9" 4" TROUBLESHOOTING CHART Risk of electrical shock. Unplug the pump before touching it or servicing it. SYMPTOM PROBABLE CAUSE(S) CORRECTIVE ACTION Pump won’t start or run. Pump is not plugged in. Make sure the pump is plugged into a proper outlet. Blown fuse or tripped breaker. Replace the fuse with a fuse of proper size. If tripped, replace breaker. Low line voltage. Check the size of the wiring on the circuit feeding the pump and from the main switch on the property. If everything is OK, contact your power company or hydro authority. Defective motor. Replace the pump. Defective switch. Replace the switch. See below. Clogged or jammed Impeller. If the impeller won’t turn, unplug the pump, remove the lower pump body, and locate the source of the binding. Replace the impeller if necessary. Pump starts and stops Backflow of water from piping. Install or replace the check valve. too often. Faulty switch. Replace the switch. Pump won’t shut off. Defective switch. Replace the switch, after first wiping and checking that switch is functional. Restricted discharge Unplug the pump, remove it from the sump, and clean the (obstacle or ice in the piping). pump and piping. Restricted intake screen. Unplug the pump, remove it from the sump, and clean the intake screen and impeller. Pump operates but Low line voltage. If the voltage is below 110 volts, check the size of the wiring delivers little or no water. from the main switch on the property. If OK, contact your power company or hydro authority. Debris caught in the impeller. Remove the pump and clean out the impeller. Worn or defective parts or Clean the impeller if it’s plugged; replace the impeller if plugged impeller. necessary; otherwise replace the pump. Check valve installed without Drill a 1/8" (3mm) dia. hole between the pump discharge and vent hole the check valve (1-2" above the pump discharge and below the waterline). Restricted intake screen. Remove the pump and clean out the intake screen. Check valve is installed either Be sure the check valve is installed correctly (the flow arrow backward or upside down. should point away from the pump). For parts or assistance, call Flotec Customer Service at 1-800-365-6832
Page 1 and 2: OWNER’S MANUAL Submersible Sump P
Page 3 and 4: Installation 3 10" Minimum with Int
Page 5: Installation / Operation 5 High Wat
Page 9 and 10: Warranty 9 RETAIN ORIGINAL RECEIPT
Page 11 and 12: Installation 11 3A. Détacher l’i
Page 13 and 14: Installation 13 Alarme de niveau é
Page 15 and 16: Debits / Diagnostic des pannes 15 D
Page 17 and 18: Garantie 17 Conserver l’original
Page 19 and 20: Instalación 19 3A. Saque el interr
Page 21 and 22: Instalación / Operación 21 Alarma
Page 23 and 24: Desempeño / Localización de falla
Page 25 and 26: Garantia 25 Conserver l’original
Page 27: Notes / Notas 27

Submersible Sump Pumps Pompes submersibles pour ... - Flotec

Create successful ePaper yourself

Delete template?

Save as template?