INSTALLATION INSTRUCTIONS 30" (76.2 CM) GAS ... - Jenn-Air
INSTALLATION INSTRUCTIONS 30" (76.2 CM) GAS ... - Jenn-Air INSTALLATION INSTRUCTIONS 30" (76.2 CM) GAS ... - Jenn-Air
WARNING Natural Gas Conversion 3. Unscrew the regulator cap and remove the plastic cover. A Tip Over Hazard A child or adult can tip the range and be killed. Install anti-tip bracket to floor or wall per installation instructions. Slide range back so rear range foot is engaged in the slot of the anti-tip bracket. Re-engage anti-tip bracket if range is moved. Do not operate range without anti-tip bracket installed and engaged. Failure to follow these instructions can result in death or serious burns to children and adults. 4. Flip the regulator cap over and replace the plastic cover. A A. Plastic cover B. Regulator cap B B C 1. Turn manual shutoff valve to the closed position. A A. To range B. Shutoff valve (closed position) C. Gas supply line 2. Unplug range or disconnect power. To Convert Gas Pressure Regulator 1. Remove access panel by grasping sides and pulling upward, lifting out. 2. Locate gas pressure regulator behind access panel. B C A. LP gas position B. Natural gas position C. Plastic cover 5. Screw the regulator cap securely back into place. Do not overtighten. To Convert Oven Bake Burner 1. Remove oven racks from inside the oven cavity. 2. Remove the oven door. See “Oven Door” section in the Use and Care Guide for oven door removal instructions. 3. Using a Phillips screwdriver, remove and set aside the 2 oven bake burner cover screws located at the front of the oven. A A A. Gas pressure regulator IMPORTANT: Do not remove the gas pressure regulator. B A. Oven bake burner cover B. Oven bake burner cover screws 4. Lift up and remove oven bake burner cover. 24
5. Unscrew 2 wing nuts and remove oven baffle. 11. Install the Number 49 Natural gas oven bake burner orifice hood, turning it clockwise 4 or 5 turns. Do not overtighten. A 49 B 6. Using a Phillips screwdriver, remove and set aside the 2 oven bake burner screws and the orifice hood cover screw. A A. Oven baffle B. Wing nuts B C A. Number 49 Natural gas oven bake burner orifice hood 12. Position the oven bake burner over the oven bake burner orifice hood and reinstall using 2 screws. B D A A. Oven bake burner screws B. Orifice hood cover C. Orifice hood cover screw D. Oven bake burner 7. Lift up and remove orifice hood cover. 8. Lift up and remove oven bake burner. 9. Locate the oven orifice hood at the back of the oven cavity. 10. Using an adjustable wrench, turn the orange Number .047 LP gas oven bake burner orifice hood counterclockwise to remove. A. Oven bake burner B. Oven bake burner orifice hood 13. Reinstall orifice hood cover. 14. Reinstall the access panel. Replace Oven Bake Burner Cover 1. Replace oven baffle and tighten 2 wing nuts. 2. To replace oven bake burner cover, insert tabs of cover into slots in oven back. Replace and tighten 2 screws at the front of the oven. .047 A A .047 A. Orange number .047 LP gas oven bake burner orifice hood A. Slots in oven back 25
- Page 1 and 2: INSTALLATION INSTRUCTIONS 30" (76.2
- Page 3 and 4: WARNING Tip Over Hazard A child or
- Page 5 and 6: Cabinet Dimensions Cabinet opening
- Page 7 and 8: Calculating Vent System Length IMPO
- Page 9 and 10: Burner Input Requirements Input rat
- Page 11 and 12: Rear Wall Venting 1. Mark the wall
- Page 13 and 14: 9. Position blower motor in cabinet
- Page 15 and 16: WARNING Make Gas Connection 5. Use
- Page 17 and 18: 10. Depending on your installation,
- Page 19 and 20: 6. To start the Bake function, pres
- Page 21 and 22: To Convert Gas Pressure Regulator 1
- Page 23: 4. Install the Number .038 LP gas o
- Page 27 and 28: Use the following chart for correct
- Page 29 and 30: SÉCURITÉ DE LA CUISINIÈRE Votre
- Page 31 and 32: ■ ■ Canalisation métallique Br
- Page 33 and 34: ■ Éviter les assemblages par ser
- Page 35 and 36: IMPORTANT : La cuisinière doit êt
- Page 37 and 38: INSTRUCTIONS D’INSTALLATION Déba
- Page 39 and 40: 5. Fixer le ventilateur au sol avec
- Page 41 and 42: 2. Tracer et découper un trou de 5
- Page 43 and 44: 2. Vérifier tous les raccordements
- Page 45 and 46: 12. Insérer le filtre d’évacuat
- Page 47 and 48: 4. Utiliser un tournevis à lame pl
- Page 49 and 50: Conversion du détendeur 1. Retirer
- Page 51 and 52: 4. Installer l’injecteur femelle
- Page 53 and 54: 4. Retourner le chapeau du détende
- Page 55 and 56: Conversion des brûleurs de surface
5. Unscrew 2 wing nuts and remove oven baffle.<br />
11. Install the Number 49 Natural gas oven bake burner orifice<br />
hood, turning it clockwise 4 or 5 turns. Do not overtighten.<br />
A<br />
49<br />
B<br />
6. Using a Phillips screwdriver, remove and set aside the 2 oven<br />
bake burner screws and the orifice hood cover screw.<br />
A<br />
A. Oven baffle<br />
B. Wing nuts<br />
B<br />
C<br />
A. Number 49 Natural gas oven bake burner orifice hood<br />
12. Position the oven bake burner over the oven bake burner<br />
orifice hood and reinstall using 2 screws.<br />
B<br />
D<br />
A<br />
A. Oven bake burner screws<br />
B. Orifice hood cover<br />
C. Orifice hood cover screw<br />
D. Oven bake burner<br />
7. Lift up and remove orifice hood cover.<br />
8. Lift up and remove oven bake burner.<br />
9. Locate the oven orifice hood at the back of the oven cavity.<br />
10. Using an adjustable wrench, turn the orange Number .047 LP<br />
gas oven bake burner orifice hood counterclockwise to<br />
remove.<br />
A. Oven bake burner<br />
B. Oven bake burner orifice hood<br />
13. Reinstall orifice hood cover.<br />
14. Reinstall the access panel.<br />
Replace Oven Bake Burner Cover<br />
1. Replace oven baffle and tighten 2 wing nuts.<br />
2. To replace oven bake burner cover, insert tabs of cover into<br />
slots in oven back. Replace and tighten 2 screws at the front<br />
of the oven.<br />
.047<br />
A<br />
A<br />
.047<br />
A. Orange number .047 LP gas oven bake burner orifice hood<br />
A. Slots in oven back<br />
25