INSTALLATION INSTRUCTIONS 30" (76.2 CM) GAS ... - Jenn-Air
INSTALLATION INSTRUCTIONS 30" (76.2 CM) GAS ... - Jenn-Air INSTALLATION INSTRUCTIONS 30" (76.2 CM) GAS ... - Jenn-Air
NOTE: If the template is misplaced, the following measurements can be used to determine the vent hole location. 6. Lift and rotate the motor 90° to reposition the electrical connection. Top View B C D A E I H F G A A. Electrical connector 7. Rotate bracket 90° and secure with 4 locknuts. A. 9" (22.8 cm) B. 3¹⁄₈" (7.9 cm) C. 8³⁄₈" (21.3 cm) D. 6³⁄₈" (16.2 cm) E. 2¼" (5.7 cm) F. 12½" (31.7 cm) G. 18¾" (47.6 cm) H. 1½" (3.8 cm) I. 3½" (8.9 cm) 4. Draw and cut a 6¼" (15.8 cm) diameter hole. 8. Remove the bracket from the other side of the blower motor, rotate 90° and secure with 4 locknuts. A B A. Option 1 B. Option 2 5. Remove the 4 locknuts on the blower side of the motor and remove the bracket. View from Motor Side of Blower A A. Electrical connector 12
9. Position blower motor in cabinet opening and mount blower motor to the floor. Top View Option 1 Option 2 Left Side Venting 1. Mark cabinet side for left side vent hole location. B A A B A A. 31³⁄₁₆" (79.2 cm) from top of cabinet B. 18" (45.7 cm) from back wall B 2. Mark and cut a 5½" (13.9 cm) diameter hole in the cabinet side. A. Inlet from range B. Exhaust outlet 10. Connect vent system to blower motor outlet (option 1 shown) with 4 - #8 x ¾" hex head screws provided. A B A. 5½" (13.9 cm) diameter hole A B 3. Mark and cut a 14" x 11" (35.6 x 27.9 cm) opening in the floor of the cabinet. Top View C D A. Inlet B. Vent clamp C. Floor D. Vent system A 11. Go to the “Make Gas Connection” section. B A. 11" (27.9 cm) from front of cabinet B. 14" (35.6 cm) from left side of cabinet 13
- Page 1 and 2: INSTALLATION INSTRUCTIONS 30" (76.2
- Page 3 and 4: WARNING Tip Over Hazard A child or
- Page 5 and 6: Cabinet Dimensions Cabinet opening
- Page 7 and 8: Calculating Vent System Length IMPO
- Page 9 and 10: Burner Input Requirements Input rat
- Page 11: Rear Wall Venting 1. Mark the wall
- Page 15 and 16: WARNING Make Gas Connection 5. Use
- Page 17 and 18: 10. Depending on your installation,
- Page 19 and 20: 6. To start the Bake function, pres
- Page 21 and 22: To Convert Gas Pressure Regulator 1
- Page 23 and 24: 4. Install the Number .038 LP gas o
- Page 25 and 26: 5. Unscrew 2 wing nuts and remove o
- Page 27 and 28: Use the following chart for correct
- Page 29 and 30: SÉCURITÉ DE LA CUISINIÈRE Votre
- Page 31 and 32: ■ ■ Canalisation métallique Br
- Page 33 and 34: ■ Éviter les assemblages par ser
- Page 35 and 36: IMPORTANT : La cuisinière doit êt
- Page 37 and 38: INSTRUCTIONS D’INSTALLATION Déba
- Page 39 and 40: 5. Fixer le ventilateur au sol avec
- Page 41 and 42: 2. Tracer et découper un trou de 5
- Page 43 and 44: 2. Vérifier tous les raccordements
- Page 45 and 46: 12. Insérer le filtre d’évacuat
- Page 47 and 48: 4. Utiliser un tournevis à lame pl
- Page 49 and 50: Conversion du détendeur 1. Retirer
- Page 51 and 52: 4. Installer l’injecteur femelle
- Page 53 and 54: 4. Retourner le chapeau du détende
- Page 55 and 56: Conversion des brûleurs de surface
NOTE: If the template is misplaced, the following<br />
measurements can be used to determine the vent hole<br />
location.<br />
6. Lift and rotate the motor 90° to reposition the electrical<br />
connection.<br />
Top View<br />
B<br />
C<br />
D<br />
A<br />
E<br />
I<br />
H<br />
F<br />
G<br />
A<br />
A. Electrical connector<br />
7. Rotate bracket 90° and secure with 4 locknuts.<br />
A. 9" (22.8 cm)<br />
B. 3¹⁄₈" (7.9 cm)<br />
C. 8³⁄₈" (21.3 cm)<br />
D. 6³⁄₈" (16.2 cm)<br />
E. 2¼" (5.7 cm)<br />
F. 12½" (31.7 cm)<br />
G. 18¾" (47.6 cm)<br />
H. 1½" (3.8 cm)<br />
I. 3½" (8.9 cm)<br />
4. Draw and cut a 6¼" (15.8 cm) diameter hole.<br />
8. Remove the bracket from the other side of the blower motor,<br />
rotate 90° and secure with 4 locknuts.<br />
A<br />
B<br />
A. Option 1<br />
B. Option 2<br />
5. Remove the 4 locknuts on the blower side of the motor and<br />
remove the bracket.<br />
View from Motor Side of Blower<br />
A<br />
A. Electrical connector<br />
12