RPH12000 CE.qxp - Ramsey Winch
RPH12000 CE.qxp - Ramsey Winch
RPH12000 CE.qxp - Ramsey Winch
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
E<br />
ATTACH TO 12V DC (+)<br />
(SEE ELECTRICAL SCHEMATIC)<br />
2.21<br />
56,1<br />
2.21<br />
56,1<br />
10.11<br />
256,8<br />
N<br />
CH<br />
GA<br />
GED*<br />
*CLUT<br />
LIT<br />
W<br />
EN<br />
H<br />
3.79<br />
96,3<br />
A<br />
16.25<br />
412,7<br />
5.53<br />
140,5<br />
A<br />
STATIC LOAD<br />
HOLDING BRAKE<br />
9.00<br />
228,6<br />
1.75<br />
44,5<br />
6.12<br />
155,4<br />
4.88<br />
124,0<br />
29.58<br />
751,3<br />
FLANGE<br />
DIA.<br />
*<br />
12.25<br />
311,2<br />
CL<br />
.50<br />
12,7 DIA.<br />
CABLE HOLE<br />
DRUM<br />
9.75<br />
247,7<br />
3.94<br />
100,0<br />
BARREL DIA.<br />
3.81<br />
96,8<br />
PRESSURE IN GIVES COUNTER-CLOCKWISE DRUM<br />
ROTATION VIEWED FROM MOTOR END<br />
ATTACH TO GROUND (SEE<br />
ELECTRICAL SCHEMATIC)<br />
.125-27NPT PORT<br />
(CONNECT 80 TO 150 PSI **<br />
PRESSURE LINE TO DISENGAGE<br />
CLUTCH)<br />
.500-13UNC X .62" (15,7 MM) DEEP<br />
TAPPED HOLE (TYP. 4 PLA<strong>CE</strong>S EACH<br />
SIDE OF WINCH)<br />
9.12<br />
231,6<br />
4.62<br />
117,3<br />
5.05<br />
128,4<br />
RAMSEY WINCH CO<br />
4.56<br />
115,8<br />
TULSA OK<br />
9.12<br />
231,6<br />
*<br />
2.25<br />
57,2<br />
(TYP.)<br />
.500-13UNC X .75" (19,1 MM) DEEP<br />
TAPPED HOLE (TYP. 4 PLA<strong>CE</strong>S EACH<br />
END BEARING)<br />
*<br />
1.12<br />
28,4<br />
*<br />
.56<br />
14,2<br />
*<br />
(TYP.)<br />
(TYP.)<br />
1.12<br />
28,4<br />
(TYP.)<br />
C WINCHL<br />
PRESSURE IN GIVES CLOCKWISE DRUM<br />
ROTATION VIEWED FROM MOTOR END<br />
VIEW A-A<br />
MOTOR CONTROL VALVE DETAIL<br />
.88<br />
22,4<br />
.875-14 SAE STRAIGHT THREAD<br />
O-RING PORT (TYP. 2 PLA<strong>CE</strong>S)<br />
DIMENSIONS SHOWN ARE INCHES OVER MILLIMETERS<br />
WINCH MOUNTING CAPSCREWS MUST MEET OR EX<strong>CE</strong>ED SAE GRADE 5 SPECIFICATION<br />
*NOTE: THESE HOLE LOCATIONS MUST BE HELD WITHIN ±.03" (0,8 MM) OF<br />
TRUE POSITION. RECOMMENDED MOUNTING HOLE DIAMETER IS .53" (13,5 MM).<br />
** CAUTION: PRESSURE MUST NOT EX<strong>CE</strong>ED 150 PSI.<br />
MODEL RPH-12,000<br />
WITH AIR CYLINDER CLUTCH SHIFTER<br />
ATTACH TO GROUND (16 GA.<br />
WIRE SUPPLIED BY CUSTOMER)<br />
12V BATTERY<br />
ATTACH TO PTO INDICATOR SWITCH TO<br />
RE<strong>CE</strong>IVE 12V DC WHEN PTO IS ENGAGED.<br />
BUTT<br />
CONNECTOR<br />
SWITCH<br />
NOTE: LIGHT SHOULD BE "ON" WHEN CLUTCH IS<br />
ENGAGED AND "OFF" WHEN CLUTCH IS DISENGAGED.<br />
_<br />
+<br />
INDICATOR LIGHT<br />
(ON WHEN CLUTCH<br />
IS ENGAGED)<br />
ELECTRICAL<br />
SCHEMATIC<br />
12