rotanta 460 rotanta 460 r rotanta 460 rc rotanta 460 rf - Hettich ...

More documents

Recommendations

Info

EN 16.2 Calling up programs • Press the PROG key. The parameters RCL is displayed. • Use the adjusting knob to set the program place you want. If a "+" is shown after the program location, then this data is write-protected. • Press the START key. Briefly, Program recall ... is displayed as confirmation. The centrifugation data of the selected program place is shown. 16.3 Write protection for programs The programs can be protected against unintentional modification. The write protection can be activated/deactivated as follows when the rotor is at a standstill: • Call up the desired program (see the chapter on "Calling up programs"). • Press the PROG key. The parameters RCL is displayed. • Press and hold the PROG button for eight seconds. After eight seconds, Set Protection = 1- (for example) appears in the display. • Set "+" or "-" with the adjusting knob. + = program is write-protected, - = program is not write-protected. • Press the START button to save the setting. 16.4 Program linkage "Program linkage" can be used to link several centrifuge operations together. A program linkage is only possible if this has been activated (parameter Multi programs = on; see the chapter on "Activating or deactivating program linkage"). 16.4.1 Activating or deactivating program linkage The program link can be activated/deactivated as follows when the rotor is at a standstill: • Press and hold the PROG button for eight seconds. After eight seconds, ∗∗∗ Machine Menu ∗∗∗ appears in the display. • Press the PROG key as often as necessary until the ->Settings is displayed. • Press the START key. The SOUND / BELL = off/on is displayed. • Press the PROG key as often as necessary until the Multi programs = off/on is displayed. • Set off or on with the adjusting knob . off = program linkage deactivated, on = program linkage activated. • Press the START key to save the setting. Briefly, Store Settings ... is displayed as confirmation, followed by -> Settings. • Press the OPEN / STOP key once to leave the "Settings" menu or press the OPEN / STOP key twice to leave the "Machine Menu". 44/147
EN 16.4.2 Linking programs or changing a program linkage It is possible to save 25 program linkages (program locations A to Z; there is no program location J). A program linkage can consist of no more than 20 programs. The speed adjustment from one program to the next one is always done in a program linkage with the start-up parameter of the next program. There cannot be any continuous operation programs in a program linkage. No centrifuge parameters may be modified in a program linkage. A parameter modification is only possible in the individual programs. The TIME button can be used during the centrifuge operation to call up the total run time of the program linkage (e. g. ∑=00:05:30) and the run time of the currently running program (e.g. t B.02=00:01:00). 1. Press the PROG button repeatedly until the parameter EDIT A…Z is displayed. 2. Use the adjusting knob to set the desired program location where the program linkage is to be saved. 3. Press the START button. The program location of the program linkage and the first program of the program linkage will be shown (e.g. EDIT B.01 = 01). 4. Use the adjusting knob to set the first program of the program linkage. 5. Press the PROG button. The next program of the program linkage will be shown (e.g. EDIT B.02 = END). 6. Use the adjusting knob to set the next program of the program linkage. 7. Press the PROG button. The next program of the program linkage will be shown (e.g. EDIT B.03 = END). 8. Repeat steps 6 and 7 until all programs have been set. 9. Set END with the adjusting knob (turn adjusting knob anti-clockwise). For program linkages which consist of 20 programs, END cannot be set after the 20th program. 10. Press the START button. STO B, for example, is displayed. 11. Press the START button to save the program linkage. As confirmation, Multi program store .. will be shown briefly. 16.4.3 Calling up program linkage • Press the PROG button repeatedly until the parameter RCL A…Z is displayed. • Use the adjusting knob to set the program place you want. Press the START key. Briefly, Multi program recall ... is displayed as confirmation. • The centrifugation data of the first program of the program linkage will be shown. 16.5 Automatic temporary storage The program place 0 serves as temporary storage for centrifugation data of the last centrifugation run that took place. No programs can be saved at this program place. After every start to a centrifugation run, the centrifugation data that is used for the run is automatically saved at program place "0" and can be accessed there. 45/147
Page 1 and 2: ROTANTA 460 ROTANTA 460 R ROTANTA 4
Page 3 and 4: 0482 EG-Konformitätserklärung EC
Page 5 and 6: DE Inhaltsverzeichnis 1 Bestimmungs
Page 7 and 8: DE 1 Bestimmungsgemäße Verwendung
Page 9 and 10: DE 4 Sicherheitshinweise Werden nic
Page 11 and 12: DE 6 Lieferumfang 1 Anschlusskabel
Page 13 and 14: DE 12 Beladen des Rotors Standard-Z
Page 15 and 16: DE • Vorkühlung des Rotors start
Page 17 and 18: DE 16.2 Programme abrufen • Die T
Page 19 and 20: DE 17 Zentrifugation Während eines
Page 21 and 22: DE 21 Angezeigte Zentrifugations-Da
Page 23 and 24: DE 25 Adresse der Zentrifuge Die Ad
Page 25 and 26: DE 33 Zentrifugation von Stoffen od
Page 27 and 28: DE 36.2 Rotoren und Zubehör 36.2.1
Page 29 and 30: DE 37 Störungen Lässt sich der Fe
Page 31 and 32: DE 39 Reparaturannahme von Zentrifu
Page 33 and 34: EN 19 Emergency Stop...............
Page 35 and 36: EN Manufacturer Andreas Hettich Gmb
Page 37 and 38: EN For further details of available
Page 39 and 40: EN 9 Interface (only for centrifuge
Page 41 and 42: EN 14 Control and display elements
Page 43: EN 15.3.2 Relative centrifugal forc
Page 47 and 48: EN 17.3 Short-time centrifugation A
Page 49 and 50: EN 24 PIN (Personal Identification
Page 51 and 52: EN 30.2 Precooling of the rotor For
Page 53 and 54: EN 36 Maintenance and servicing The
Page 55 and 56: EN 36.2.5 Rotors and accessories wi
Page 57 and 58: EN Message / fault Cause Remedy SEN
Page 59 and 60: FR 18 Modifier les réglages pendan
Page 61 and 62: FR Fabricant Andreas Hettich GmbH &
Page 63 and 64: FR Lorsque la suspension d'un syst
Page 65 and 66: FR 9 Interface (uniquement pour les
Page 67 and 68: FR 14 Organes de commande et indica
Page 69 and 70: FR 15.2 Vitesse de rotation (RPM)
Page 71 and 72: FR 16.4.1 Activer ou désactiver as
Page 73 and 74: FR 17.2 Fonctionnement continu •
Page 75 and 76: FR 23 Paramétrer verrouillage du p
Page 77 and 78: FR 27 Interrogation des heures de s
Page 79 and 80: FR 33 Centrifugation de matières e
Page 81 and 82: FR 36.2 Rotors et accessoires 36.2.
Page 83 and 84: FR 37 Défauts Si l'erreur ne peut
Page 85 and 86: FR 39 Réparation des centrifugeuse
Page 87 and 88: IT 18 Modifica delle impostazioni d
Page 89 and 90: IT Costruttore Andreas Hettich GmbH
Page 91 and 92: IT Senza l’impiego di un sistema
Page 93 and 94: IT 9 Interfaccia (solo per la centr
Page 95 and 96:
IT 14 Elementi di operazione e visu
Page 97 and 98:
IT 15.2 Numero di giri (RPM) • Pr
Page 99 and 100:
IT 16.4.1 Attivare o disattivare co
Page 101 and 102:
IT 17.2 Funzionamento continuo •
Page 103 and 104:
IT 23 Impostare bloccaggi di progra
Page 105 and 106:
IT 27 Consultazione delle ore di fu
Page 107 and 108:
IT 33 Centrifugazione di sostanze o
Page 109 and 110:
IT 36.2 Rotori ed accessori 36.2.1
Page 111 and 112:
IT 37 Guasti Se non si riesce a eli
Page 113 and 114:
IT 39 Accettazione di centrifughe d
Page 115 and 116:
DE EN 5624 5625-A + 5627 Ausschwing
Page 117 and 118:
DE EN 5624 5628 + 5629 Ausschwingro
Page 119 and 120:
DE EN 5624 5628 + 5220-A Ausschwing
Page 121 and 122:
DE EN 5624 5628 + 5220-A + 5280 Aus
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
DE EN 5624 5623-A + 5621 5623-A Aus
Page 129 and 130:
DE EN 5624 5620-A + 4844 + 5280 Aus
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
DE EN 4446 5051 + 5280 5053 Ausschw
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
DE EN 5615 Winkelrotor 6-fach / Ang
Page 145 and 146:
Page 147:
DE EN 4444 4412-A + 5280 + 4414 Aus
show all

rotanta 460 rotanta 460 r rotanta 460 rc rotanta 460 rf - Hettich ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?