Dialogue essais-simulation et identification de lois de comportement ...

Partie A – Chapitre 2 : Caractérisation du comportement sous chargement biaxial
(Doyoyo et Wierzbicki 2003) Doyoyo M.et Wierzbicki T. (2003). Experimental studies on the yield
behavior of ductile and brittle aluminum foams. International Journal of Plasticity 19, 1195-1214.
(El-hajjar et Haj-Ali 2004) El-Hajjar R., Haj-Ali R. (2004). In-plane shear testing of thick-section
pultruded FRP composites using a modified Arcan fixture, Composites Part B 35, 421-428.
(Ferron et Makinde 1988) Ferron G. et Makinde A. (1988). Design and development of a biaxial
strength testing device. Journal of Testing Evaluation, 16, 253-256.
(Gall et al. 1998) Gall K., Jacobus K., Sehitoglu H.et Maier H.J (1998). Stress-induced martensitic phase
transformations in polycrystalline CuZnAl shape memory alloys under different stress states.
Metallurgical and Materials Transactions A 29, 765-773.
(Grolleau et al. 2009) Grolleau V., Louche H., Penin A., Chauvelon P., Rio G., Liu Y., Favier D. (2009).
Bulge tests on ferroelastic and superelastic NiTi sheets with full field thermal and 3D-kinematical
measurements: experiments and modelling. ESOMAT 2009, 06011.
pastel-00910076, version 1 - 27 Nov 2013
(Grolleau et al. 2011) Grolleau V., Louche H., Delobelle V., Penin A., Rio G., Liu Y., Favier D. (2011).
Assessment of tension–compression asymmetry of NiTi using circular bulge testing of thin plates.
Scripta Materialia 65, 347–350.
(Hannon et Tierman 2008) Hannon A.et Tiernan P. (2008). A review of planar biaxial tensile test
systems for sheet metal. Journal of Materials Processing Technology 198, 1-13.
(Kuwabara 2007) Kuwabara T. (2007). Advances in experiments on metal sheets and tubes in support
of constitutive modeling and forming simulations. International Journal of Plasticity 23, 385-419.
(Lecompte et al. 2007) Lecompte D., Smits A., Sol H., Vantomme J. et Hemelrijck D. V. (2007). Mixed
numerical–experimental technique for orthotropic parameter identification using biaxial tensile tests
on cruciform specimens. International Journal of Solids and Structures 44, 1643-1656.
(Lexcellent et al. 2002) Lexcellent C., Vivet A., Bouvet C., Calloch S. et Blanc, P. (2002). Experimental
and numerical determinations of the initial surface of phase transformation under biaxial loading in
some polycrystalline shape-memory alloys. J. Mech.and Phys. of Solids 50, 2717–2735.
(Machado et al. 2012) Machado G., Chagnon G.et Favier D. (2012). Induced anisotropy by the Mullins
effect in filled silicone rubber. Mechanics of Materials 50, 70-80.
(Mohr et Ebnoether 2009) Mohr D.et Ebnoether F. (2009). Plasticity and fracture of martensitic boron
steel under plane stress conditions. International Journal of Solids and Structures 46, 3535-3547.
(Mohr et Jacquemin 2008) Mohr D. et Jacquemin J. (2008). Large deformation of anisotropic
austenitic stainless steel sheets at room temperature: Multiaxial experiments and phenomenological
modeling. Journal of the Mechanics and Physics of Solids 56, 2935-2956.
(Mohr et Oswald 2008) Mohr D. et Oswald M. (2008). A new experimental technique for the multiaxial
testing of advanced high strength steel sheets. Experimental Mechanics 48(1), 65-77.
(Pottier et al. 2012) Pottier T., Vacher P., Toussaint F., Louche H., & Coudert T. (2012). Out-of-plane
testing procedure for inverse identification purpose: application in sheet metal
plasticity. Experimental mechanics, 52(7), 951-963.
52