MAN-Rotina380-e - Hettich AG, CH

More documents

Recommendations

Info

EN 17 Change the settings during the centrifugation run The running time, the speed, the relative centrifugal acceleration (RCF), the centrifuging radius, the run-up and rundown parameters as well as the temperature (for centrifuges with cooling only) can be changed while the centrifuge is running. • Select the parameter you want and use the adjusting knob to change the value (see chapter "Entering centrifugation parameter"). • Press the START key. The changed setting is saved at program place "0" (see chapter "Automatic temporary storage"). The program place number is displayed in parentheses (0). The original program is not overwritten. 18 Emergency Stop • Press the STOP / OPEN key twice. During a not-stop, run-out is carried out with braking level 9 (shortest run-out). Braking level 9 is displayed. If braking level 0 has been preselected, run-out is carried out with braking level 9d. With braking level 9d, the run-out time is longer, technically speaking, than braking level 9. 19 Acoustic signal The acoustic signal sounds: • Upon the appearance of a disturbance in 2 second intervals. • After completion of a centrifugation run and rotor standstill in 30 second intervals. The acoustic signal is stopped by opening the lid or pressing any key. The signal after completion of the centrifugation run can be activated or deactivated in the following manner, if the rotor is at standstill: • Keep the PROG key held down for 8 seconds. After 8 seconds, ∗∗∗New machine ∗∗∗ appears in the display. • Press the PROG key as often as necessary until the ->Settings is displayed. • Press the START key. The SOUND / BELL = off/on is displayed. • Use the adjusting knob to set off or on. • Press the START key to save the setting. Briefly, Store Settings ... is displayed as confirmation, followed by -> Settings. • Press the STOP / OPEN key once to leave the "Settings" menu or press the STOP / OPEN key twice to leave the "Machine Menu". 20 Displayed centrifugation data after switch-on. After switch-on the centrifugation data from program 1, or from the last program that was used, is displayed. If the rotor is at standstill, this can be set as follows: • Keep the PROG key held down for 8 seconds. After 8 seconds, ∗∗∗New machine ∗∗∗ appears in the display. • Press the PROG key as often as necessary until the ->Settings is displayed. • Press the START key. The SOUND / BELL = off/on is displayed. • Press the PROG key as often as necessary until Start program = Last/First is displayed. • Use the adjusting knob to set Last or First. Last = the program used last, First = program 1. • Press the START key to save the setting. Briefly, Store Settings ... is displayed as confirmation, followed by -> Settings. • Press the STOP / OPEN key once to leave the "Settings" menu or press the STOP / OPEN key twice to leave the "Machine Menu". 21 Set temperature unit The temperature can be entered in degrees Celsius (°C) or in degrees Fahrenheit (°F). When the rotor is at standstill, the temperature unit must be set as follows: • Keep the PROG key held down for 8 seconds. After 8 seconds, ∗∗∗New machine ∗∗∗ appears in the display. • Press the PROG key as often as necessary until the ->Settings is displayed. • Press the START key. The SOUND / BELL = off/on is displayed. • Press the PROG key as often as necessary until Temp Unit = Celsius/Fahrenheit is displayed. • Use the adjusting knob to set Celsius or Fahrenheit. • Press the START key to save the setting. Briefly, Store Settings ... is displayed as confirmation, followed by -> Settings. • Press the STOP / OPEN key once to leave the "Settings" menu or press the STOP / OPEN key twice to leave the "Machine Menu". 34/105
EN 22 Centrifuge address Ex works, the address is ] = 29. Address is set. The address should not be changed. 23 Functions RCF integral, B-Ramp and multi programs These functions are not activated as standard. 24 Query of operating hours and the number of centrifugation runs The operating hours are divided up into internal and external operating hours. Internal operating hours: Total time the device was switched on. External operating hours: Total time of previous centrifugation runs. The operating hours and the number of centrifugation runs can be queried as follows when the rotor is at standstill: • Keep the PROG key held down for 8 seconds. After 8 seconds, ∗∗∗New machine ∗∗∗ appears in the display. • Press the PROG key as often as necessary until the -> Operating Time is displayed. • Press the START key. The external operating hours are displayed, e.g. OP Time ext = 0h25m. • Press the PROG key. The internal operating hours are displayed, e.g. OP Time int = 1h36m. • Press the PROGkey. The number of centrifugation runs is displayed, e.g. Number of Starts = 10. • Press the STOP / OPEN key to leave the menu, "Operating Time" or press the key STOP / OPEN three times to leave the "Machine Menu". 25 Querying system information Rotor information and the program version of the centrifuge as well as the frequency converter can be queried as follows when the rotor is at a standstill: • Keep the PROG key held down for 8 seconds. After 8 seconds, ∗∗∗New machine ∗∗∗ appears in the display. • Press the PROG key as often as necessary until the ->Info is displayed. • Press the START key. The rotorcode (rotor), the maximum rotor speed (Nmax) and the preset centrifuging radius (R) of the last rotor that was recognized by the rotor recognition , e.g. Rotor 4∗: Nmax = 4500 R=184. The last recognized rotor is marked with a star (∗). Use the adjusting knob to have the information of the rotors permitted in the centrifuge displayed. • Press the PROG key. The program version of the centrifuge is displayed, e.g. SW version = 01.00. • Press the PROGkey. The program version of the frequency converter is displayed e.g. FC-SW-Version = 4. • Press the STOP / OPEN key twice to leave the "Info" menu or press the key STOP / OPEN three times to leave the "Machine Menu". 26 Immediate display of centrifugation data after switch-on. • Switch on the power supply. (Switch setting Ι). • The first time the display changes optically, (inverse display) press any key and keep it held down. The centrifugation data is displayed immediately. 35/105
Page 1 and 2: ROTINA 380 ROTINA 380 R DE Bedienun
Page 3 and 4: EG-Konformitätserklärung EC Confo
Page 5 and 6: DE Inhaltsverzeichnis 1 Bestimmungs
Page 7 and 8: DE 1 Bestimmungsgemäße Verwendung
Page 9 and 10: DE 5 Bedeutung der Symbole Symbol a
Page 11 and 12: DE 10 Ein- und Ausbau des Rotors A
Page 13 and 14: DE 14 Zentrifugations-Parameter ein
Page 15 and 16: DE 16 Zentrifugation Während eines
Page 17 and 18: DE 21 Temperatur-Einheit einstellen
Page 19 and 20: DE 30 Rotor-Erkennung Nach jedem St
Page 21 and 22: DE 33 Störungen Lässt sich der Fe
Page 23 and 24: EN Contents 1 Use according to spec
Page 25 and 26: EN 1 Use according to specification
Page 27 and 28: EN 5 Symbol meanings Symbol on the
Page 29 and 30: EN 11 Loading the rotor Standard ce
Page 31 and 32: EN 14 Enter centrifugation paramete
Page 33: EN 16 Centrifugation When the centr
Page 37 and 38: EN 29 Centrifugation of materials w
Page 39 and 40: EN 33 Faults If the fault cannot be
Page 41 and 42: FR Table des matières 1 Usage conf
Page 43 and 44: FR 1 Usage conforme La présente ma
Page 45 and 46: FR 5 Signification des symboles Sym
Page 47 and 48: FR 10 Montage et démontage du roto
Page 49 and 50: FR STOP OPEN • Terminer le cycle
Page 51 and 52: FR 15.2 Saisie / modification du pr
Page 53 and 54: FR 20 Données de centrifugation af
Page 55 and 56: FR 28 Accélération centrifuge rel
Page 57 and 58: FR 32.3 Autoclavage Les rotors à o
Page 59 and 60: FR Message / Erreur Origine Solutio
Page 61 and 62: IT 25 Consultazione delle informazi
Page 63 and 64: IT 4 Indicazioni inerenti la sicure
Page 65 and 66: IT 8 Messa in funzione • Secondo
Page 67 and 68: IT RCF • Accelerazione centrifuga
Page 69 and 70: IT 14.5 Temperatura (soltanto per c
Page 71 and 72: IT 17 Modifica delle impostazioni d
Page 73 and 74: IT 26 Visualizzazione immediata dei
Page 75 and 76: IT 32 Pulizia e manutenzione Prima
Page 77 and 78: IT 33 Guasti Se non si riesce a eli
Page 79 and 80: DE EN 37 Anhang / Appendix 37.1 Rot
Page 81 and 82: DE EN 1754 1752 + 1751 Ausschwingro
Page 83 and 84: DE EN 1754 1752 + 1751 Ausschwingro
Page 85 and 86:
DE EN 1798 5051 + 5053 Ausschwingro
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
DE EN 1711 1377 1378 1379 Topfrotor
Page 93 and 94:
DE EN 1720 Winkelrotor 6-fach / Ang
Page 95 and 96:
DE EN 1789 Winkelrotor 30-fach / An
Page 97 and 98:
DE EN 1792 Winkelrotor 6-fach / Ang
Page 99 and 100:
DE EN 1726 1661 1660 Ausschwingroto
Page 101 and 102:
DE EN 1748 1661 1660 1660 1680 Auss
Page 103 and 104:
Page 105:
DE EN 1798 5051 + 5280 5053 Ausschw
show all

MAN-Rotina380-e - Hettich AG, CH

Create successful ePaper yourself

Delete template?

Save as template?