Instruction Robby G3 - webpark ag
Instruction Robby G3 - webpark ag
Instruction Robby G3 - webpark ag
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
English<br />
10 <strong>Robby</strong> <strong>G3</strong><br />
The pool-vacuumer <strong>Robby</strong> <strong>G3</strong> truly works fully automatically!<br />
Brushes and vacuums the bottom of the pool, most of all the dirty areas<br />
in corners and edges.<br />
Is made for pools of any shape or size built of any material - needs no<br />
special adjustments.<br />
Works without electricity. While the <strong>Robby</strong> <strong>G3</strong> is cleaning, you can have<br />
a safe swim in the swimming-pool.<br />
Has a built in pre-filter.<br />
Cleans when the pool is covered too.<br />
1. Limitations:<br />
Required capacity of the filter should be bigger than 18 gal/min.<br />
Up to 20% maximal slope of the pool-bottom.<br />
Runs most economically in pools of a maximum of 25 yd length.<br />
2. Functional parts:<br />
1. Connecting tube<br />
2. Adaptor clamp<br />
3. Suction hose (not included in the delivery pack<strong>ag</strong>e)<br />
4. Handle<br />
5. Turning knob (speed indicator)<br />
6. Turbine<br />
7. Gear unit<br />
8. Driving wheel unit<br />
9. Bottom with brushes<br />
10. Big pre-filter for large debris<br />
11. Back wheel<br />
12. Flaps<br />
3. Using the <strong>Robby</strong> <strong>G3</strong><br />
1.The handling is child’s play. It essentially functions like a manual vacuum.<br />
2. Fully switch the water-flow from the drain to the skimmer<br />
3. Attach the suction hose (3) to the connecting tube (1) of the<br />
<strong>Robby</strong> <strong>G3</strong>, and if required, secure it with the adaptor clamp (2).<br />
4. Whilst holding the suction hose (3) let the ROBBY <strong>G3</strong> sink to the<br />
pool-bottom.<br />
5. Fill the suction hose (3) with water and plug it into the skimmer or into<br />
the specially provided plug (Hint: To fill the suction hose you can hold it<br />
<strong>ag</strong>ainst an inlet jet-stream for a couple of seconds, until there are no<br />
rising air-bubbles visible anymore).<br />
6. <strong>Robby</strong> <strong>G3</strong> starts to work.<br />
4. Cleaning:<br />
The cleaning-time depends on both the size of the pool and how dirty it is.<br />
For example: Pool of 13x26 ft. approx. 3 hours.<br />
After cleaning:<br />
1. Pull the suction-hose off the skimmer or the suction-plug.<br />
2. Return the drain to its previous position.<br />
3. Dr<strong>ag</strong> the <strong>Robby</strong> <strong>G3</strong> out of the water, grab the handle and tilt the<br />
<strong>Robby</strong> <strong>G3</strong> backwards allowing the water to flow out of the <strong>Robby</strong> <strong>G3</strong><br />
through the flaps (12).<br />
4. From time to time the pre-filter 10) needs to be emptied. To do so,<br />
remove the bottom (9) by loosening the 3 wing-nuts. The dirt can be<br />
rinsed off using an ordinary garden-hose.<br />
5. Do not store the ROBBY <strong>G3</strong> in water, as this will affect the life span of the<br />
gear unit.<br />
OPERATING INSTRUCTIONS