DigiTrace TCON-CSD/20

More documents

Recommendations

Info

6 Technical data 15 Supply Supply voltage 230V AC +10/-15% Power consumption < 2VA Housing Material polycarbonate Mounting 35mm x 7.5mm DIN rail to EN 50 022 Operating position unrestricted Weight approx. 110g Protection IP<strong>20</strong> Flammability class UL 94 V0 Electrical data Data backup EEPROM Connection screw terminals for wire cross-sections up to 2.5 mm2 max. Electromagnetic compatibility EN 61 326 - interference emission Class B - immunity to interference to industrial requirements Electrical safety EN 61 010, Part 1, overvoltage category III, pollution degree 2
7 Alarm messages The following alarm messages can be shown in the temperature display: Error message Cause Elimination - Check sensor and connecting cable for damage or short circuit. Display overrun The measured value is too large and outside the range. - Check whether the correct sensor has been set or connected. 7 Alarm messages 16 v Chapter 4 “Commissioning the instrument” H These messages are only output to the temperature display. Display underrun The measured value is too small and outside the range. h Cancel switch-on delay with + Time for switch-on delay after power ON has elapsed. With display over/underrun, the switch-on delay becomes ineffective. Value has fallen below the low alarm limit temperature ProcVal h Depending on the controller type that was set, check whether the heating or cooling unit functions faultlessly. h Check whether the installed relay fuse is still in good working order. ProcVal Value has gone above the high alarm limit temperature ProcVal The alarm disappears as soon as the temperature goes above or below the AL limits by the amount of the hysteresis.
Page 1 and 2: DigiTrace TCON-CSD/20 Digitaler The
Page 3 and 4: Inhalt 1 Geräteausführung identif
Page 5 and 6: 1 Geräteausführung identifizieren
Page 7 and 8: 3 Elektrischer Anschluss 3.1 Instal
Page 9 and 10: 4 Gerät in Betrieb nehmen 4.1 Anze
Page 11 and 12: Regler Wertebereich von...werkseiti
Page 13 and 14: Wertebereich von...werkseitig...bis
Page 15 and 16: 4.3 Bedienrechte vergeben (Freigabe
Page 17 and 18: 6 Technische Daten Messeingang Beze
Page 19: 7 Alarmmeldungen In der Temperatura
Page 23 and 24: DigiTrace TCON-CSD/20 Digital Therm
Page 25: Contents 1 Instrument identificatio
Page 28 and 29: 2 Assembling Disassembling °C 2 As
Page 30 and 31: 3.2 Connection diagram Supply volta
Page 32 and 33: 4.2 Setting the instrument function
Page 34 and 35: Value range from...factory-set...to
Page 36 and 37: Value range from...factory-set...to
Page 38 and 39: 5 Operation Alter target temperatur
Page 44 and 45: INSTALL-100 R0-03/05
Page 46 and 47: Aperçu des fonctions L’affichage
Page 49 and 50: 1 Identification de l’appareil La
Page 51 and 52: 3 Raccordement électrique 3.1 Inst
Page 53 and 54: 4 Mise en service de l’appareil 4
Page 55 and 56: Régulateur Plage des valeurs de...
Page 57 and 58: Plage des valeurs de...d’usine...
Page 59 and 60: 4.3 Attribution du code d’accès
Page 61 and 62: 6 Données techniques Entrée de me
Page 63: 7 Messages d’erreur Les messages

DigiTrace TCON-CSD/20

Create successful ePaper yourself

Delete template?

Save as template?