DigiTrace TCON-CSD/20

More documents

Recommendations

Info

2 Assembling Disassembling °C 2 Assembling 3 (1) (2) 90 55 0 ≤ 75
3 Electrical connection 3.1 Installation notes 3 Electrical connection 4 a The choice of cable, the installation, the fusing and the electrical connection must conform to the requirements of VDE 0100 “Regulations on the Installation of Power Circuits with nominal voltages below 1000 V” or the appropriate local regulations. a The electrical connection must only be carried out by qualified personnel. a The electromagnetic compatibility conforms to the standards and regulations listed under Technical data. a The instrument is not suitable for installation in areas with an explosion hazard. a Apart from faulty installation, incorrect settings on the thermostat (setpoint, parameter level data) may also affect the proper functioning of controlled processes or lead to damage. Provision should therefore always be made for safety devices that are independent of the thermostat, e. g. overpressure valves or temperature limiters/monitors. Adjustment must be restricted to specialist personnel (lock parameters for operation). Please observe the corresponding safety regulations in this matter. Unfavorable parameter adjustment may result in unstable control. The process value obtained should therefore be monitored for its stability and knowledge about the process should be obtained. a The load circuit must be fused for the maximum relay current in order to prevent welding of the output relay contacts in the event of a short circuit. a Do not connect any additional loads to the supply terminals of the instrument. a The external fuse of the supply should not be rated below 1A, depending on the conductor cross-section. If contact with live components is possible while working on the thermostat, it must be disconnected on both poles from the supply. a Supply Measurement input and supply AC short-circuit-proof electrically isolated from each other
Page 1 and 2: DigiTrace TCON-CSD/20 Digitaler The
Page 3 and 4: Inhalt 1 Geräteausführung identif
Page 5 and 6: 1 Geräteausführung identifizieren
Page 7 and 8: 3 Elektrischer Anschluss 3.1 Instal
Page 9 and 10: 4 Gerät in Betrieb nehmen 4.1 Anze
Page 11 and 12: Regler Wertebereich von...werkseiti
Page 13 and 14: Wertebereich von...werkseitig...bis
Page 15 and 16: 4.3 Bedienrechte vergeben (Freigabe
Page 17 and 18: 6 Technische Daten Messeingang Beze
Page 19: 7 Alarmmeldungen In der Temperatura
Page 23 and 24: DigiTrace TCON-CSD/20 Digital Therm
Page 25: Contents 1 Instrument identificatio
Page 30 and 31: 3.2 Connection diagram Supply volta
Page 32 and 33: 4.2 Setting the instrument function
Page 34 and 35: Value range from...factory-set...to
Page 36 and 37: Value range from...factory-set...to
Page 38 and 39: 5 Operation Alter target temperatur
Page 40 and 41: 6 Technical data 15 Supply Supply v
Page 44 and 45: INSTALL-100 R0-03/05
Page 46 and 47: Aperçu des fonctions L’affichage
Page 49 and 50: 1 Identification de l’appareil La
Page 51 and 52: 3 Raccordement électrique 3.1 Inst
Page 53 and 54: 4 Mise en service de l’appareil 4
Page 55 and 56: Régulateur Plage des valeurs de...
Page 57 and 58: Plage des valeurs de...d’usine...
Page 59 and 60: 4.3 Attribution du code d’accès
Page 61 and 62: 6 Données techniques Entrée de me
Page 63: 7 Messages d’erreur Les messages

DigiTrace TCON-CSD/20

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?