Rheotest english

More documents

Recommendations

Info

7. After that, you can insert the whole drive of cylinder measuring device down into the temperature controlvessel (8). Fix the measuring drive on the stand with the knurled screw (2). Carry out measurementsafter the necessary tempering of sample. After measurements disassemble is carried out in reverseorder.34
9 Software RHEOTEST ® RN 5 Manager9.1 User InterfaceThe software RHEOTEST RN 5Manager corresponds to generalstandards of MICROSOFT ® Windowsprograms. After starting the program,the login window appears. Additionalenquiry could appear concerningthermostat activation depending uponsettings. After this user interfaceappears.1 – Main menu2 – Inlays3 – Job tree4 – Sample tree9.1.1 InlaysPresentation is organized in inlays ofsettings and analysis results. Theycould be selected by pressing name of an inlay.• Job: It is shown certain job and settings of the actual selected sample, control keys to begin an analysisand detailed information about selected sample at the moment.• Table: Table of data is shown in accordance with the settings.• Chart: Chart is shown in accordance with the settings.• Report: Report data are shown as statistic evaluation or calculated rheological parameters.• Method: It is shown job method or methods in methods’ library.9.1.2 Tree for Jobs, Samples and MethodsDesignators for two trees are at the left side of window in RHEOTEST RN 5 Manager. Theyare independent of the selected inlay for job, table, plot or report.Through the upper tree it is possible to select a job in jobs’ group that should be presented.The corresponding image will be activated and active sample will be shown from the selectedjob after click.It is possible to select active sample in the job in the low structural tree.After selection the corresponding image will be active and data for all tests will be shown.It is necessary to click + sign in front of sample name, if it is necessary to display only onetest. After this individual tests will be listed. If only one test is selected, so only those datasare shown in table or graph.Width and height of structural trees could be adjusted, if necessary.Methods groups with their methods will be shown at upper tree, if display is activated ofmethods library. Method with its settings will be shown after click.9.1.3 Help SystemThe software gives context help on the basis of the Operating Manual.This has advantage that information from Operating Manual corresponds to information inOnline-Help.35
Page 1 and 2: RHEOTEST Medingen GmbHOperation Man
Page 3 and 4: Contents1 Introduction ............
Page 5 and 6: 9.5.2.5.3 Print ...................
Page 7 and 8: 1 IntroductionThe Rheometer finds i
Page 9 and 10: 5 Technical Manual5.1 Technical Spe
Page 11 and 12: 5.2.2 Adapter for a Rheometer with
Page 13 and 14: Figure 4 System of Exchangeable Mea
Page 15 and 16: 5.3 Control UnitThe on/off switch (
Page 17 and 18: 5.4.2 Cone/Plate and Plate/Plate Me
Page 19 and 20: 5.5 Peltier Tempering SystemThe pre
Page 21 and 22: Note: The Peltier control unit may
Page 23 and 24: • Then contact the energy supply
Page 25 and 26: 8 Test Preparation and Measurement8
Page 27 and 28: Figure 13 Setting up the Basic Plat
Page 29 and 30: Figure 15 Adapter5. Again, move dow
Page 31 and 32: 6. After clicking OK, the program r
Page 33: 8.2 Use Cylinder Measuring SystemsW
Page 37 and 38: 1 - Job Name: the job name should d
Page 39 and 40: 8 - use RN temperature only: Applic
Page 41 and 42: If communication between RHEOTEST
Page 43 and 44: 9.2.6.10 Table Settings -> CopyTabl
Page 45 and 46: directory name. Imported job’s gr
Page 47 and 48: Table heading makes possible to dis
Page 49 and 50: 3 - Min: Minimum value of X axis. D
Page 51 and 52: 5 - Grid Color: specifies the grid
Page 53 and 54: 5 - add Settings: It will be added
Page 55 and 56: Note: By a choice from the selectio
Page 57 and 58: 8 - Copy Test: The actual test is t
Page 59 and 60: CS-Test decides on the start value
Page 61 and 62: option gives an automatic concatena
Page 63 and 64: Angle Abort Limit: 360°, not requi
Page 65 and 66: In addition, the “Export / Import
Page 67 and 68: 9.7.1.1 Main menu Edit9.7.1.1.1 Edi
Page 69 and 70: 8 - Cancel: All changes will be rej
Page 71 and 72: They will be updated when Service-J
Page 73 and 74: 7 - Phone: Input of phone number of
Page 75 and 76: The following procedure exists for
Page 77 and 78: 12 - Cancel: All changes will be re
Page 79 and 80: 9.7.5 Pt100Pt100 calibration could
Page 81 and 82: It will be printed maximal possible
Page 83 and 84: 10 Bitumen measurements10.1 General
Page 85 and 86:
DSR-Test (T-Sweep). The temperature
Page 87 and 88:
Please make sure that there is no s
Page 89 and 90:
- Resolve the knurled screw (2) (Fi
Page 91 and 92:
- Put the sample on the basic plate
Page 93 and 94:
All Jobs start with appropriate tem
Page 95 and 96:
data Gr. X Y meaning calculation un
Page 97 and 98:
MeterBinghamHerschel BulkleyCassonC
Page 99 and 100:
11.5 Calibration of measuring syste
Page 101 and 102:
11.7 Error messages11.7.1 Error mes
show all

Rheotest english

Create successful ePaper yourself

Delete template?

Save as template?