HELASTA POLYESTER MINERAL HELASTA ... - Index S.p.A.

ReinforcementThicknessMass per unit area MINERALRoll sizeWatertightnessPeelresistance L/TShearresistance L/TMaximum tensileforce L/TElongation L/TResistanceto impactResistance to staticloadingResistance to tearing(nail shank) L/TDimensionalstability L/TFlexibility to low temp.• after ageingFlow resist. at high temp.• after ageingReaction to fireEuroclassExternal fireperformanceStandardEN 1849-1EN 1849-1EN 1848-1EN 1928 – BEN 12316-1EN 12317-1EN 12311-1EN 12311-1EN 12691 – AEN 12730 - AEN 12310-1EN 1107-1EN 1109EN 1296-1109EN 1110EN 1296-1110EN 13501-1EN 13501-5HELASTA POLYESTERFLAMINA. Plastic protection film helping prevent coils from sticking to the roll.As it withdraws under the action of the flame right during its installation, it signalsthe best melting point in order to correctly glue the membrane to the brackets andrises. When not heated, it can be used as a sliding layer.T±0,2±15%≥≥–20 N–20%–20%–15% V.A.–30%≤≤+15°C≥–10°CHELASTAMINERAL HELASTAPOLYESTERPOLYESTER“Non-woven” composite polyester“Non-woven” composite polyesterstabilized with fibreglassstabilized with fibreglass4 mm 5 mm 4 mm – –– – – 4.0 kg/m 2 4.5 kg/m 21×10 m 1×10 m 1×10 m 1×10 m 1×10 m60 kPa 60 kPa 60 kPa– 200 N/50 mm –800/600 N/50 cm 800/600 N/50 cm 750/600 N/50 cm850/700 N/50 cm 850/750 N/50 cm 850/750 N/50 cm50/50% 50/50% 50/50%1250 mm 1250 mm –20 kg 20 kg –200/200 N 200/200 N 200/200 N–0.30/+0.30% –0.30/+0.30% –0.30/+0.30%–25°C –25°C –25°C–25°C –25°C –25°C100°C 100°C 100°C90°C 90°C 90°CE E EF roof F roof F roofThermal specificationsThermal conductivity0.2 W/mK 0.2 W/mK 0.2 W/mK 0.2 W/mK 0.2 W/mKHeat capacity5.20 KJ/K 6.50 KJ/K 4.80 KJ/K 4.80 KJ/K 5.40 KJ/KCompliant with EN 13707 in terms of the resistance factor to steam penetration for reinforced polymer-bitumen membranes, the value of µ = 20 000 may be considered, unless declared otherwise.ElastoplastomericpolymerbitumenFlaminaCompositepolyester/glassreinforcementElastoplastomericpolymerbitumenTECHNICAL CHARACTERISTICSFlaminaCOMPOSITION OF THE MEMBRANEPRODUCT FINISHINGMINERAL PROTECTION. On the visible face of the membrane, a protectivecoating made up of slate granules of various colours is hot bonded. This mineralshield protects the membrane from ageing caused by UV rays.MINERAL HELASTA POLYESTERElastoplastomericpolymerbitumenSelf-protectedwith slate granulesCompositepolyester/glassreinforcementSelvedgeElastoplastomericpolymerbitumenFlaminathe numerous possible uses and the possible interference of conditions orelements beyond our control, we assume no responsibility regarding the resultswhich are obtained. The purchasers, of their own accord and under their ownresponsibility, must establish the suitability of the product for the envisaged use.The figures shown are average indicative figures relevant to current productionand may be changed or updated by INDEX at any time without previous warning.The advice and technical information provided, is what results from our bestknowledge regarding the properties and the use of the product. Considering• FOR ANY FURTHER INFORMATION OR ADVICE ON PARTICULAR APPLICATIONS, CONTACT OUR TECHNICAL OFFICE • IN ORDER TO CORRECTLY USE OUR PRODUCTS, REFER TO INDEX TECHNICAL SPECIFICATIONS •Cg - 1.000 - 6/2012 ingInternet: www.indexspa.itFor technical and commercial information: tecom@indexspa.itAccounting department: index@indexspa.itExport department: index.export@indexspa.itVia G. Rossini, 22 - 37060 Castel D’Azzano (VR) - Italy - C.P.67 - Tel. (+39)045.8546201 - Fax (+39)045.518390© INDEX“GBC Italia” Associated