Altivar 11

More documents

Recommendations

Info

DéfautULFsous-charge courantUSFsoustensionRemèdeNiveau de courant inférieur au seuil de sous-charge LUL• Vérifier la valeur des paramètres LUL et tUL dans le menu FLt page 12.• Vérifier la tension et le paramètre tension.FRANÇAIS17
ENGLISHSteps for Setting Up the Drive1 - Mount the drive2 - Connect the following to the drive:• The line supply, ensuring that it is:- within the voltage range of the drive- voltage free• The motor, ensuring that its connections correspond to the supply voltage• The control via the logic inputs• The speed reference via the logic or analog inputs3 - Apply input power to the drive, but do not give a run command4 - Configure the following:• The nominal frequency (bFr) of the motor, if it is other than 50 Hz for the E range or other than 60 Hz for the U range(only appears the first time the drive is switched on).• The ACC (Acceleration) and dEC (Deceleration) parameters.• The LSP (Low speed when the reference is zero) and HSP (High speed when the reference is maximum) parameters.• The ItH parameter (Motor thermal protection).• The preset speeds SP2-SP3-SP4.5 - Configure the following in the AIt menu:• The speed reference if it is other than 0 - 5 V (0 -10V or 0 -20mA or 4 -20mA or X-Y mA).6 - Configure the following in the drC menu:The motor parameters, only if the factory configuration of the drive is not suitable.7 - Start the driveFactory configurationThe Altivar 11 is factory-configured for the most common operating conditions:• Logic inputs:- LI1, LI2 (2 directions of operation): 2-wire control on transition, LI1 = forward, LI2 = reverse.- LI3, LI4: 4 preset speeds (speed 1 = speed reference or LSP, speed 2 = 10 Hz, speed 3 = 25 Hz, speed 4 = 50 Hz).• Analog input AI1: speed reference (0 + 5 V).• Relay R1: The contact opens in the event of a fault (or drive off).• DO output: analog output, image of the motor frequency.If the factory configuration is not suitable, the FUn menu can be used to modify the functions and the I/O assignments.Dimensionsb2= == G =acH4= =ATV 11HammbmmcmmGmmHmmØmmU05pp E, U ranges 72 142 y 125 60±1 131±1 2 x 5 M4bH U09pp U rangeU09pp E range 72 142 y 138 60±1 120±1 2 x 5 M4U12pp E range= G = U18Mp E rangea U18Mp U range 72 147 138 60±1 131±1 2 x 5 M4U18F1 U range 117 142 156 106±1 131±1 4 x 5 M4cU29pp E, U rangesU41pp E, U rangesScrewsATV 11PammbmmcmmGmmHmmØmmall ratings 72 142 101 60±1 131±1 2 x 5 M4Screws18
Page 1 and 2: Guide d'exploitationUser's manualBe
Page 3 and 4: FRANÇAISLes étapes de la mise en
Page 5 and 6: Borniers puissanceAlimentation puis
Page 7 and 8: Fonctions de l'afficheur et des tou
Page 9 and 10: Menu entrée analogique AItCes para
Page 11 and 12: Menu Fonctions applications FUnFRAN
Page 13 and 14: FRANÇAISCode Description Prérégl
Page 15 and 16: FRANÇAISCode Description Prérégl
Page 17: FRANÇAISDéfauts - causes - remèd
Page 21 and 22: Power terminalsPower supplyPower su
Page 23 and 24: Functions of the display and the ke
Page 25 and 26: Analog input menu AItThese paramete
Page 27 and 28: Application functions menu FUnFUnEN
Page 29 and 30: Code Description Factory setting-:5
Page 31 and 32: ENGLISHCode Description Factory set
Page 33 and 34: ENGLISHFaults - Causes - RemediesDr
Page 35 and 36: DEUTSCHVorgehensweise zur Inbetrieb
Page 37 and 38: LeistungsklemmenleistenLeistungsver
Page 39 and 40: Funktionen der Anzeige und der Tast
Page 41 and 42: Menü „Analogeingang“ AItDie Pa
Page 43 and 44: Menü „Anwendungsfunktionen“ FU
Page 45 and 46: Code Beschreibung WerkseitigeVorein
Page 47 and 48: DEUTSCHCode Beschreibung Werkseitig
Page 49 and 50: Menü „Überwachung“ SUP;
Page 51 and 52: StörungULFUnterstromUSFUnterspannu
Page 53 and 54: ESPAÑOLEtapas de la instalación1
Page 55 and 56: Borneros de potenciaAlimentación d
Page 57 and 58: Funciones del visualizador y las te
Page 59 and 60: Menú de entrada analógica AItEsto
Page 61 and 62: Menú de funciones de aplicación F
Page 63 and 64: Cód. Descripción Ajuste de fábri
Page 65 and 66: Cód. Descripción Ajuste de fábri
Page 67 and 68: Fallos - causas - solucionesEl vari
Page 69 and 70:
Le fasi della messa in opera1 - Fis
Page 71 and 72:
Morsettiere potenzaAlimentazione po
Page 73 and 74:
Funzioni del display e dei tasti•
Page 75 and 76:
Menu ingresso analogico AItQuesti p
Page 77 and 78:
Menu Funzioni applicazioni FUnFUnEN
Page 79 and 80:
Codice Descrizione Preregolazione d
Page 81 and 82:
Codice Descrizione Preregolazione d
Page 83 and 84:
Difetti - cause - procedure di inte
Page 85 and 86:
Requirements for North American Mar
show all

Altivar 11

Create successful ePaper yourself

Delete template?

Save as template?