FX06 Field Controller - Tech-System
FX06 Field Controller - Tech-System FX06 Field Controller - Tech-System
FX06 Field ControllerInstallation GuideP/N 24-85737-955 Rev. CIssue Date 08 2007READ THIS INSTRUCTION SHEET AND THE SAFETY WARNINGSCAREFULLY BEFORE INSTALLING AND SAVE IT FOR FUTURE USEGeneral Features• The FX06 is a compact Field Controller in the Facility Explorer range ofproducts. It provides all the features of the FX05 (Advanced) Controller inan enhanced enclosure design with some new and extended features.The controller has been specifically designed for single and doublecompressor chillers, heat pumps, single circuits, fan coil units, smallclose control units (CCU) and small air handling units (AHU).• It has 17 physical input & output and supports a wide range oftemperature sensors, including active sensors, for the measurement ofhumidity, pressure and other variables, and actuating devices.• This controller has a state-of-the-art LCD display including a set ofgraphic status icons used in the most common HVAC/R applications(two compressor symbols; Alarm, high pressure, low pressure andmaintenance symbols; Heat, cool, defrost and electric heat symbols).• It is available with plug-in communication modules to enable thecontroller to be integrated into an N2 Open or LONWORKS ® compatiblebuilding automation system. In addition the FX06 field controller alsofeatures communications services to transmit event notificationmessages via Short Messaging Service (SMS).• A Real Time Clock circuit supports the start-stop scheduling ofequipment and real time based control sequences.• It is fully programmable or configurable using the FX Tools softwarepackages, for a wide range of commercial environmental controlapplications.• It is suitable for use in normal non-hazardous and non-corrosiveenvironments.Figure 1:Dimensions in mm (inches)FX06 Field Controller - Installation Guide1
MountingFigure 2: Panel cut-out• Make a cut-out in the mounting panel.Figure 3:Figure 4:WiringFixing Bracket Removala. Press on the side tabsb. Sliding the bracket backwards leaving the gasket in placearound the front panel of the FX06 enclosure.Panel mountinga. Insert the FX06 Field Controller through the panel cut-outfrom the front side of the panel.b. Secure it in place by replacing the fixing bracket from theback.WARNING: Use this FX06 Field Controller only as anoperating control. Where failure or malfunction of the FX06could lead to personal injury or damage to the controlledequipment or other property, additional precautions must bedesigned into the control system. Incorporate and maintainother devices such as supervisory or alarm systems or safetyor limit controls that are intended to warn of, or protectagainst, failure or malfunction of the FX06 Field Controller.WARNING: Risk of Electric Shock and Property Damage.Disconnect or isolate all power supplies before makingelectrical connections. More than one disconnect or isolationmay be required to completely de-energize equipment.Contact with components carrying hazardous voltage cancause electric shock and may result in severe personal injuryor death.• Wiring terminations are made by detachable, easy to plug connectors.A pre-assembled set of cables with connectors are provided with mostcontroller models and a set of cables is also available for orderingseparately (see “Ordering Codes”).• Complete the wiring connections and verify that the wiring has beencorrectly installed, and that voltage levels are appropriate for the variousinput signals according to the application.• Keep all cables as short as possible and tie in position.2 FX06 Field Controller - Installation Guide
- Page 3: Figure 1: Dimensions in mm (inches)
- Page 6 and 7: Figure 9: Communication Module Dime
- Page 10 and 11: Figure 5:Figure 6:Figure 7:Figure 8
- Page 12 and 13: Technical SpecificationsProductFX06
- Page 14 and 15: Contrôleur de champs FX06Guide d
- Page 16 and 17: Figure 5:Figure 6:Figure 7:Figure 8
- Page 18 and 19: Caractéristiques techniquesProduit
- Page 20 and 21: FX06 Field-ControllerInstallationsa
- Page 22 and 23: Abbildung 5: LP-FX06P0x Verdrahtung
- Page 24 and 25: Technische MerkmaleProduktFX06 Fiel
- Page 26 and 27: Field Controller FX06Guida all’in
- Page 28 and 29: Figura 5:Figura 6:Figura 7:Figura 8
- Page 30 and 31: Specifiche tecnicheProdottoField Co
- Page 32 and 33: Controlador de campo FX06Guía de I
- Page 34 and 35: Figura 5:Figura 6:Figura 7:Figura 8
- Page 36 and 37: Especificaciones técnicasProductoC
- Page 38 and 39: FX06 VeldregelaarInstallatie-instru
- Page 40 and 41: Figuur 5: LP-FX06P0x Bedradingssche
- Page 42 and 43: Technische specificatiesProductFX06
- Page 44 and 45: Fältstyrenhet FX06Installationsgui
- Page 46 and 47: Figur 5:Figur 6:Figur 7:Figur 8:LP-
- Page 48 and 49: Tekniska specifikationerProduktFäl
- Page 50 and 51: Řadič FX06Instalační návodČ.
- Page 52 and 53: Obrázek 5: Schéma zapojení zař
- Page 54 and 55: Technické údajeProduktŘadič FX0
- Page 56: Johnson Controls International, Inc
MountingFigure 2: Panel cut-out• Make a cut-out in the mounting panel.Figure 3:Figure 4:WiringFixing Bracket Removala. Press on the side tabsb. Sliding the bracket backwards leaving the gasket in placearound the front panel of the <strong>FX06</strong> enclosure.Panel mountinga. Insert the <strong>FX06</strong> <strong>Field</strong> <strong>Controller</strong> through the panel cut-outfrom the front side of the panel.b. Secure it in place by replacing the fixing bracket from theback.WARNING: Use this <strong>FX06</strong> <strong>Field</strong> <strong>Controller</strong> only as anoperating control. Where failure or malfunction of the <strong>FX06</strong>could lead to personal injury or damage to the controlledequipment or other property, additional precautions must bedesigned into the control system. Incorporate and maintainother devices such as supervisory or alarm systems or safetyor limit controls that are intended to warn of, or protectagainst, failure or malfunction of the <strong>FX06</strong> <strong>Field</strong> <strong>Controller</strong>.WARNING: Risk of Electric Shock and Property Damage.Disconnect or isolate all power supplies before makingelectrical connections. More than one disconnect or isolationmay be required to completely de-energize equipment.Contact with components carrying hazardous voltage cancause electric shock and may result in severe personal injuryor death.• Wiring terminations are made by detachable, easy to plug connectors.A pre-assembled set of cables with connectors are provided with mostcontroller models and a set of cables is also available for orderingseparately (see “Ordering Codes”).• Complete the wiring connections and verify that the wiring has beencorrectly installed, and that voltage levels are appropriate for the variousinput signals according to the application.• Keep all cables as short as possible and tie in position.2 <strong>FX06</strong> <strong>Field</strong> <strong>Controller</strong> - Installation Guide