MÁQUINA DUPLICADORA TITAN KEY CUTTING ... - Jma.es

3Operationand performance2.5Components and functional parts3.1Machine adjustment2.5.1 Accesories See figure 41 Non-adjustable size 18 spanner.2 Keys for sideways and depth adjustment of themachine.3 Wedges to adjust the tip of the key.4 Recessed wedges for duplicating cruciform keys.5 Set of allen keys (2, 2.5, 3, 4, 5, 6).6 Rod with Ø1,207 Rod with Ø1,708 Rod for changing the milling cutter (Ø7x70).2.5.2 Electrical circuit See figure 5The main components of the electrical and electronic circuitsare as follows:12345Current collectorStart button with red light.MicroswitchBlack button for brushMotor2.5.3 2 Sided clamp See figure 6The clamp has been designed to hold a family of differentkeys on each side. In the diagram, the duplicationpossibilities on each side of the clamp are shown.12Duplication of the key supported on the reverse side:- Keys with normal blade- Keys with narrow blade, with the help of rods- Cruciform keysDuplication by means of the clamping the keyto the guide (outline).Sideways or depth adjustment of the machine is performedin the following way:TAKE CARE! : Before touching anything when adjustingthe machine, switch off the main on-off switch so thatthe milling cutter cannot begin operating.3.1.1 Sideways control and adjustment See figure 7Position the adjustment keys (1) in the clamps, sothat the head of the adjustment keys goes in as faras possible and is touching the inner stop of side 1or 2 of the clamp.Next, tighten the clamp.Move the clamps with the adjustment keys (1) towardsthe tracer point (I) and the milling cutter (F), so thatthe adjustment keys are in the correct position withrespect to the tracer point and the milling cutter.This is achieved by pressing the button (P) and gentlymoving the carriage nearer to the tracer point (I) andthe milling cutter (F). See figure no. 2.In the event that the grooves of the adjustmentkeys do not coincide properly with the tracer pointand the milling cutter, proceed as follows:Loosen the support screw (T), and turn the micrometer screw (K) so that the tracer point supportmoves to the left or right so that it corresponds withthe groove of the corresponding adjustment key.The distance is now perfectly adjusted, with the tracerpoint and milling cutter coinciding with the respectivegrooves of the adjustment keys. Next, tighten thesupport screw (T), thus locking them in position.3.1.2 Control and adjustment of cutting depth See figure 8Position the adjustment keys (1) in the clamps, sothat the head of the adjustment key goes in as far aspossible and is touching the inner stop of side 1 or 2of the clamp.Move the clamps with adjustment keys (1) towardsthe tracer point (I) and the milling cutter (F) sothat the adjustment keys are resting on the tracerpoint and the milling cutter. The machine carriageis unlocked by pressing the button (P).Turn the milling cutter by hand. If the milling cuttergently scrapes against the adjustment keys then themachine has been properly adjusted.If the milling cutter turns freely, i.e. does not scrapeagainst the adjustment keys, this shows that themilling cutter is too far back in relation to the tracerand cutting is not sufficient. On the other hand, ifthe milling cutter is blocked by the adjustment keys,this shows that the milling cutter is too far forwardin relation to the tracer and cutting too deep.If either of the two situations above occur, proceedas follows:- Loosen the setscrew (L) which secures the tracerpoint (I) and turn the micrometer screw (H). Seefigure no. 3.- Move the tracer point forwards or backwards untilthat milling cutter turns and gently scrapes againstthe adjustment key. Next, tighten the tracer pointscrew (L). The machine is now in perfect workingorder.9English