Sans titre - Atlantic-comfort.com

More documents

Recommendations

Info

Thank you for choosing this device. It has undergone many tests and inspections to ensure its quality. We hope thatyou will be completely satisfied.Some recommendationsPlease read the documentation before starting to install the panel heater.Disconnect power before working on the panel heater.Conserve the documentation, even after installation of the panel heater.Equipment specification : (indicated on the label of the device):IP24 : Equipped protected from water splashes.Class II : Double insulation.: Appliance in accordance with the European Directive 2002/96/CE (DEEE).1) Where to install the panel heater ? 1 2 3INSTALLATION OF THE PANEL HEATER- This equipment was designed to be installed in a residence. Please askyour distributor before using it for any other purpose.- The panel heater should be installed according to normal tradepractice and in compliance with legislation in the relevant country (theIEE Wiring Regulations).- Comply with the minimum clearance distances as indicated in diagram(schemas 2 and 3) for positioning of the panel heater. Never usethe shelf for vertical equipment.- If your wall covering is laid on foam, a spacer the same thicknessas the foam must be placed under the panel heater’s support. Thisensures there is free space behind the panel heater to make sure itscontrol settings are not adversely affected.- Do not install the panel heater:➫ In a draught likely to affect the control settings (under afan, etc.).➫ Under a fixed mains power socket.➫ In zone 1 of bathrooms.➫ In the bathroom, if the controls can be operated by aperson using the shower or the bath.Except in the UK. Please refer to the IEE Regulations601-06-01 and 601-08-01 (BS7671).12Devices must not be installed above an altitude of1000 m as the altitude causes the air outlet temperatureto rise (by around 10°C per 1000 m difference in level).2) How to install the panel heater ?32-1) Mount the wall support- Place the bracket on the floor. 4.1/4 bis- Mark the holes, to determine the position of the lower attachments.- Raise the bracket, making the previously marked holes coincide sothat you can locate the remaining two holes 4.2/4 bis- Drill holes and bracket fix 4.2/4 bis- Fit the wall support with 4 screws (horizontal model) or 6 screws(vertical model) having a maximum diameter of 6.Note : Do not use the device in mobile or feets or on casters.(diagram 4 ter).4
2-3) Locking the panel heater onto its wall bracket :Horizontal Model:- Mount the panel heater on hooks S as shown in the diagram 6.- Bring back the panel heater towards the support then to raise (arrow 1 and 2).- Introduce the legs of the support into the holes of the panel heater and lower (arrow 3). Your panel heater is fixed.Hight Model :6bisInstall the device on the S support as shown in diagram 6bis.Lock it by turning the V loch through a quarter turn.1326bisS61) Description of the control unit 7 ➔ Mode switch slider. ➔ Temperature adjusting dial(active in manual mode )V1 ➔ Heating light.USING THE PANEL HEATER2) Remote control modeSet the cursor to .You can control the heater with the remote control in this position.Stand in front of the heater and direct the remote control towards the infrared cell 8.V17Note: during installation remove the protective film from the infrared cell to ensure better use of the remote control.8Horizontal ModelHight Model
Page 2 and 3: Nous vous remercions pour le choix
Page 4 and 5: 2-3) Verrouiller l’appareil sur s
Page 6: Si l’appareil émet plusieurs BIP
Page 12 and 13: 2.1 Description of the remote contr
Page 14 and 15: Le agradecemos haber elegido este a
Page 16 and 17: 2-3) Fijar el aparato en el soporte
Page 18 and 19: Si el aparato emite varios BIP, sig
Page 20 and 21: Obrigado pela escolha deste aparelh
Page 22 and 23: 2-3) Bloquear o aparelho no seu sup
Page 24 and 25: Se o aparelho emitir vários bips,

Sans titre - Atlantic-comfort.com

Create successful ePaper yourself

Delete template?

Save as template?