AirConServiceCenter ASC2500 - WAECO - AirCon Service
AirConServiceCenter ASC2500 - WAECO - AirCon Service AirConServiceCenter ASC2500 - WAECO - AirCon Service
Operation AirCon Service Center 8.6.3 Filling process 1. Enter the preferred settings and press ENTER to confirm. Filling phase? Yes No I NOTE 2. If “Filling phase” has been selected, enter the required value, otherwise continue with “Select connections”. 3. Enter the refrigerant oil quantity. 4. Press the cursor key . 5. Enter the additive quantity. 6. Press the cursor key . 7. Enter the refrigerant quantity. 8. Press ENTER to confirm all settings. • If extraction is taking place in the same process sequence, the quantity of fresh oil is counted as an additional filling quantity, and is added to the drained oil quantity extracted beforehand. If this value is set to 0, exactly the quantity of oil which was extracted will be filled again. • To add fresh oil or UV additive, a vacuum process must be performed in the same process sequence. If no vacuum process has been selected, only refrigerant can be selected in the filling menu. 8.6.4 Selecting connections ENTER-OK STOP-EXIT PAG oil ml. 1 UV tracer ml. 7 Refrigerant g. 500 ENTER-OK STOP-EXIT 1. Select the parameters in accordance with the air conditioning system connections: • Air conditioning system has a high pressure and a low pressure connection: Select LP / HP. • Air conditioning system only has a high pressure connection: Select HP. • Air conditioning system only has a low pressure connection: Select LP. 86 EN
AirCon Service Center Operation 2. Press ENTER to confirm. HP/LP HP LP ENTER-OK STOP-EXIT PORT PORT PORT 3. Once all settings have been entered, press ENTER to start the process. Process start? 8.6.5 After ending the air conditioning service ✓ After the air conditioning service has finished, you will be prompted to disconnect the hoses of the AirConServiceCenter from the vehicle air conditioning system. 1. Disconnect the service hoses (10) and (11) and press ENTER to confirm. ✓ The service hoses will now be drained. The device is then ready for further use. 2. Screw the valve caps of the air conditioning system back on the connections. 8.7 Flushing the air conditioning system I NOTE ENTER-OK STOP-EXIT The “Flushing” menu is used to flush the vehicle air conditioning system with fresh refrigerant. Flushing is especially suitable for replacing old compressor oil or removing most metallic residue from the system. Before flushing, the refrigerant must first be extracted from the air conditioning system. Afterwards, the system components which cannot be flushed must be disconnected from the refrigerant circuit (for example, the compressor or filter). After that, the components to be flushed are connected to the service ports of the AirConServiceCenter using special adapters to form a flushing circuit. 1. First fit the connections of the AirConServiceCenter to the vehicle air conditioning system and open them. 2. In the basic menu, use the cursor keys or to select “Free selection”: Short selection Free selection Other selections ENTER-OK EN 87
- Page 36 and 37: Betrieb AirCon Service Center 17. M
- Page 38 and 39: Servicearbeiten AirCon Service Cent
- Page 40 and 41: Servicearbeiten AirCon Service Cent
- Page 42 and 43: Servicearbeiten AirCon Service Cent
- Page 44 and 45: Servicearbeiten AirCon Service Cent
- Page 46 and 47: Servicearbeiten AirCon Service Cent
- Page 48 and 49: Servicearbeiten AirCon Service Cent
- Page 50 and 51: Servicearbeiten AirCon Service Cent
- Page 52 and 53: Entsorgung AirCon Service Center 10
- Page 54 and 55: Was tun, wenn? AirCon Service Cente
- Page 56 and 57: Contents AirCon Service Center 1 Ab
- Page 58 and 59: About this operating manual AirCon
- Page 60 and 61: Safety AirCon Service Center Each t
- Page 62 and 63: Optional extras AirCon Service Cent
- Page 64 and 65: Overview of the AirConServiceCenter
- Page 66 and 67: Initial start-up AirCon Service Cen
- Page 68 and 69: Initial start-up AirCon Service Cen
- Page 70 and 71: Initial start-up AirCon Service Cen
- Page 72 and 73: Initial start-up AirCon Service Cen
- Page 74 and 75: Operation AirCon Service Center 8 O
- Page 76 and 77: Operation AirCon Service Center 8.2
- Page 78 and 79: Operation AirCon Service Center 8.2
- Page 80 and 81: Operation AirCon Service Center 8.
- Page 82 and 83: Operation AirCon Service Center 8.5
- Page 84 and 85: Operation AirCon Service Center 8.6
- Page 88 and 89: Operation AirCon Service Center 3.
- Page 90 and 91: Service tasks AirCon Service Center
- Page 92 and 93: Service tasks AirCon Service Center
- Page 94 and 95: Service tasks AirCon Service Center
- Page 96 and 97: Service tasks AirCon Service Center
- Page 98 and 99: Service tasks AirCon Service Center
- Page 100 and 101: Service tasks AirCon Service Center
- Page 102 and 103: Service tasks AirCon Service Center
- Page 104 and 105: Service tasks AirCon Service Center
- Page 106 and 107: Troubleshooting AirCon Service Cent
- Page 108 and 109: Technical data AirCon Service Cente
- Page 110 and 111: Acerca de estas instrucciones de us
- Page 112 and 113: Seguridad AirCon Service Center 2 S
- Page 114 and 115: Volumen de entrega AirCon Service C
- Page 116 and 117: Vista general del AirConServiceCent
- Page 118 and 119: Primera puesta en funcionamiento Ai
- Page 120 and 121: Primera puesta en funcionamiento Ai
- Page 122 and 123: Primera puesta en funcionamiento Ai
- Page 124 and 125: Primera puesta en funcionamiento Ai
- Page 126 and 127: Primera puesta en funcionamiento Ai
- Page 128 and 129: Funcionamiento AirCon Service Cente
- Page 130 and 131: Funcionamiento AirCon Service Cente
- Page 132 and 133: Funcionamiento AirCon Service Cente
- Page 134 and 135: Funcionamiento AirCon Service Cente
<strong>AirCon</strong> <strong>Service</strong> Center<br />
Operation<br />
2. Press ENTER to confirm.<br />
HP/LP<br />
HP<br />
LP<br />
ENTER-OK STOP-EXIT<br />
PORT<br />
PORT<br />
PORT<br />
3. Once all settings have been entered, press ENTER to start the<br />
process.<br />
Process start?<br />
8.6.5 After ending the air conditioning service<br />
✓ After the air conditioning service has finished, you will be prompted to<br />
disconnect the hoses of the <strong><strong>AirCon</strong><strong>Service</strong>Center</strong> from the vehicle air<br />
conditioning system.<br />
1. Disconnect the service hoses (10) and (11) and press ENTER to<br />
confirm.<br />
✓ The service hoses will now be drained. The device is then ready for<br />
further use.<br />
2. Screw the valve caps of the air conditioning system back on the<br />
connections.<br />
8.7 Flushing the air conditioning system<br />
I<br />
NOTE<br />
ENTER-OK STOP-EXIT<br />
The “Flushing” menu is used to flush the vehicle air conditioning system<br />
with fresh refrigerant. Flushing is especially suitable for replacing old<br />
compressor oil or removing most metallic residue from the system.<br />
Before flushing, the refrigerant must first be extracted from the air<br />
conditioning system. Afterwards, the system components which cannot be<br />
flushed must be disconnected from the refrigerant circuit (for example, the<br />
compressor or filter). After that, the components to be flushed are connected<br />
to the service ports of the <strong><strong>AirCon</strong><strong>Service</strong>Center</strong> using special adapters to<br />
form a flushing circuit.<br />
1. First fit the connections of the <strong><strong>AirCon</strong><strong>Service</strong>Center</strong> to the vehicle air<br />
conditioning system and open them.<br />
2. In the basic menu, use the cursor keys or to select “Free<br />
selection”:<br />
Short selection<br />
Free selection<br />
Other selections<br />
ENTER-OK<br />
EN 87