AirConServiceCenter ASC2500 - WAECO - AirCon Service
AirConServiceCenter ASC2500 - WAECO - AirCon Service
AirConServiceCenter ASC2500 - WAECO - AirCon Service
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>AirCon</strong> <strong>Service</strong> Center<br />
Troubleshooting<br />
Problem Cause Remedy<br />
The display shows<br />
“Not enough UV. Add!”<br />
The display shows<br />
“Not enough oil. Add!”<br />
The display shows<br />
“Max. filling time<br />
exceeded! Carry on?”<br />
The display shows<br />
“External tank empty or<br />
closed valve. Check!”<br />
The display shows<br />
“Change the equipment<br />
drier filter! Carry on?”<br />
The display shows<br />
“Change the vacuum<br />
pump oil! Carry on?”<br />
The display shows<br />
“Printer not in line! Carry<br />
on?”<br />
The display shows<br />
“Error 01”<br />
The display shows<br />
“Error 02”<br />
The display shows<br />
“Error 09”<br />
This message appears<br />
during the filling process if<br />
there is not enough UV<br />
additive in the container to<br />
finish the process.<br />
Message that appears during<br />
the filling process if there is<br />
not enough fresh oil in the<br />
container to finish the<br />
process.<br />
Message that appears during<br />
the filling process if the set<br />
amount of refrigerant cannot<br />
be filled.<br />
Message that appears at the<br />
start or during the filling of<br />
the internal refrigerant<br />
container if the set refrigerant<br />
quantity cannot be attained.<br />
This message appears when<br />
you switch on the<br />
<strong><strong>AirCon</strong><strong>Service</strong>Center</strong>.<br />
This message appears when<br />
you switch on the<br />
<strong><strong>AirCon</strong><strong>Service</strong>Center</strong>.<br />
Message indicates a printer<br />
fault.<br />
Refrigerant was added<br />
before draining was<br />
completed.<br />
The air conditioning system<br />
is leaking. There is still<br />
refrigerant in the air<br />
conditioning system.<br />
Low pressure connector not<br />
connected to the flush<br />
container during flushing.<br />
Fill the UV additive container.<br />
Top up the fresh oil container<br />
with a suitable oil type.<br />
Check that<br />
<strong><strong>AirCon</strong><strong>Service</strong>Center</strong><br />
connections are not blocked.<br />
Check if the external<br />
refrigerant container still<br />
contains enough refrigerant<br />
or if the valves of the external<br />
refrigerant container are<br />
open.<br />
Change the internal filter as<br />
soon as possible (see<br />
Page 92). To skip this, press<br />
ENTER for 3 seconds.<br />
Change the vacuum pump oil<br />
as soon as possible (see<br />
Page 96). To skip this, press<br />
ENTER for 3 seconds.<br />
Check if there is paper in the<br />
printer.<br />
Check if the printer is<br />
switched on (yellow LED<br />
must light up constantly).<br />
Check that the cover is<br />
closed properly.<br />
Repeat the draining<br />
procedure; do not interrupt it<br />
this time.<br />
Fix the leak.<br />
Connect low pressure hose<br />
to the flush box and open<br />
valve.<br />
EN 107