Manual de Montaje CLIMAVER - Technical Insulation
Manual de Montaje CLIMAVER - Technical Insulation
Manual de Montaje CLIMAVER - Technical Insulation
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Construimos tu Futuro<br />
El aprovechamiento <strong>de</strong> «retales»<br />
<strong>de</strong> panel o la necesidad <strong>de</strong> construir<br />
conductos <strong>de</strong> gran sección<br />
nos orientarán hacia la forma más<br />
lógica <strong>de</strong> fabricar el conducto. El<br />
trazado y corte se <strong>de</strong>be realizar<br />
por la cara interior <strong>de</strong>l panel, y a<br />
partir <strong>de</strong>l bor<strong>de</strong> macho <strong>de</strong>l panel.<br />
3.1. Fabricación <strong>de</strong> un<br />
Conducto Recto <strong>de</strong> una Pieza<br />
Se trata <strong>de</strong> realizar un tramo recto<br />
<strong>de</strong> medida interior a x b. Todos los<br />
cortes <strong>de</strong>scritos se realizan partiendo<br />
<strong>de</strong>l canto macho <strong>de</strong>l panel<br />
y avanzando hacia el hembra.<br />
1. Se colocará la Regla-escuadra<br />
<strong>CLIMAVER</strong> MM con la medida<br />
<strong>de</strong> uno <strong>de</strong> los lados <strong>de</strong> la<br />
sección interna <strong>de</strong>l conducto a<br />
obtener a, <strong>de</strong> forma que coincida<br />
con el bor<strong>de</strong> izquierdo <strong>de</strong>l<br />
panel <strong>CLIMAVER</strong> (1). Se pasará<br />
la herramienta <strong>CLIMAVER</strong> MM<br />
con distintivo ROJO (2).<br />
(1)<br />
distintivo<br />
Rojo<br />
2. Se colocará la Regla-escuadra<br />
<strong>CLIMAVER</strong> MM con la medida<br />
b <strong>de</strong>l otro lado <strong>de</strong> la sección<br />
interna <strong>de</strong>l conducto a obtener<br />
a partir <strong>de</strong>l corte situado<br />
más a la <strong>de</strong>recha realizado por<br />
la herramienta <strong>de</strong> distintivo<br />
ROJO que se acaba <strong>de</strong> emplear<br />
(2)<br />
(3). En dicha medida, se pasará<br />
la herramienta <strong>CLIMAVER</strong> MM<br />
con distintivo ROJO (4).<br />
(3)<br />
3. Se repetirá el paso 2) pero con la<br />
medida a, colocando la medida<br />
en el último corte (5) y pasando<br />
<strong>de</strong> nuevo la herramienta<br />
<strong>CLIMAVER</strong> MM <strong>de</strong> distintivo<br />
ROJO (6).<br />
(5)<br />
distintivo<br />
Rojo<br />
distintivo<br />
Rojo<br />
(4)<br />
4. Por último <strong>de</strong>l mismo modo<br />
que en 2) y 3) se colocará la<br />
regla-escuadra en la medida b<br />
a partir <strong>de</strong>l último corte <strong>de</strong>recho<br />
(7), pero en lugar <strong>de</strong> pasar<br />
la herramienta <strong>de</strong> distintivo<br />
ROJO, se pasará la herramienta<br />
<strong>CLIMAVER</strong> MM con distintivo<br />
AZUL (8), encargada <strong>de</strong> realizar<br />
la última ranura a media<br />
ma<strong>de</strong>ra y <strong>de</strong> <strong>de</strong>jar la solapa<br />
para el grapado.<br />
Con el cuchillo se dará un corte<br />
para separar la parte <strong>de</strong> panel<br />
sobrante.<br />
(6)