M. I. Raúl Jean Perilliat
M. I. Raúl Jean Perilliat M. I. Raúl Jean Perilliat
TORNILLOS • Se emplean dos tipos de tornillos: ordinarios (A307) y de alta resistencia (A325 y A490). Las fallas de los tornillos pueden ser: • del tornillo por cortante. • de la placa por cortante. • del tornillo por aplastamiento. • de la placa por aplastamiento • del tornillo en tensión. • del tornillo por flexión. • de la placa por tensión La falla puede ser en el tornillo o en el material conectado.
TORNILLOS Fig. 2 Posibles formas de falla de conexiones atornilladas
- Page 1 and 2: ESTRUCTURAS DE ACERO CURSO SOBRE SE
- Page 3 and 4: CONTENIDO Temario: Conceptos genera
- Page 5 and 6: Conceptos generales R y % R y Ducti
- Page 7 and 8: Resistencia a flexión M p, M y %M
- Page 9 and 10: CONTENIDO Temario: Conceptos genera
- Page 11 and 12: LOSAS EN SECCIÓN COMPUESTA
- Page 13 and 14: LOSAS EN SECCIÓN COMPUESTA A B C 7
- Page 15 and 16: LOSAS EN SECCIÓN COMPUESTA
- Page 17 and 18: CONTENIDO Temario: Conceptos genera
- Page 19 and 20: CONEXIONES ¿cuál es el objetivo d
- Page 21 and 22: CONEXIONES
- Page 23: TORNILLOS • La forma más sencill
- Page 27 and 28: TORNILLOS Tensión Figura 4.Curvas
- Page 29 and 30: TORNILLOS Esfuerzos de tensión de
- Page 31 and 32: TORNILLOS • La resistencia al cor
- Page 33 and 34: TORNILLOS RESISTENCIA DE DISEÑO EN
- Page 35 and 36: TORNILLOS RCDF-2004
- Page 37 and 38: TORNILLOS Fig. 15. Esfuerzos por ap
- Page 39 and 40: TORNILLOS 1. 4 F Rn u d t L d
- Page 41 and 42: TORNILLOS TAMAÑOS DE LOS AGUJEROS
- Page 43 and 44: TORNILLOS RCDF-2004……Los tornil
- Page 45 and 46: TORNILLOS La resistencia de diseño
- Page 47 and 48: SOLDADURA Fig. 10 Soldaduras de pen
- Page 49 and 50: SOLDADURA Suposiciones: 1.- La fall
- Page 51 and 52: SOLDADURA RESISTENCIA DE LAS SOLDAD
- Page 53 and 54: SOLDADURA Esfuerzos combinados
- Page 55 and 56: SOLDADURA Tamaño nominal del filet
- Page 57 and 58: SOLDADURA
- Page 59 and 60: SOLDADURA
- Page 61 and 62: SOLDADURA
- Page 63 and 64: SOLDADURA
- Page 65 and 66: SOLDADURA
- Page 67 and 68: SOLDADURA
- Page 69 and 70: SOLDADURA
- Page 71 and 72: SOLDADURA
- Page 73 and 74: SOLDADURA
TORNILLOS<br />
• Se emplean dos tipos de tornillos: ordinarios (A307) y de<br />
alta resistencia (A325 y A490).<br />
Las fallas de los tornillos pueden ser:<br />
• del tornillo por cortante.<br />
• de la placa por cortante.<br />
• del tornillo por aplastamiento.<br />
• de la placa por aplastamiento<br />
• del tornillo en tensión.<br />
• del tornillo por flexión.<br />
• de la placa por tensión<br />
La falla puede ser en el tornillo o en el material conectado.