ALAN 8001S EURO

More documents

Recommendations

Info

E N G L I S H 3 2 4 1 Fig.4 Microphone plug pin numbers viewed from rear of pin receptacle. Be sure that the housing and the knurled ring of Fig. 3 are pushed back onto the microphone cable before starting to solder. If the washer is not captive to the pin receptacle body, make sure that it is placed on the threaded portion of the pin receptacle body before soldering. If the microphone jack is used to hold the pin receptacle during the soldering operation, best results are obtained when the connections to pin 1 and 3 are made first and then the connections to pins 2, 4. Use a minimum amount of solder and be careful to prevent excessive solder accumulation on pins, which could cause a short between the pin and the microphone plug housing. 6. When all soldering connections to the pins of the micro phone plug are complete, push the knurled ring and the housing forward and screw the housing onto the threaded portion of the pin receptacle body. Note the location of the screw clearance hole in the plug housing with respect to the threaded hole in the pin receptacle body. When the housing is completely threaded into the pin receptacle body, a final fraction of a turn either clockwise or counterclockwise may be required to align the screw hole with the threaded hole in the pin receptacle body. When these are aligned, the retaining screw is then screwed into the place to secure the housing to the pin receptacle body. 7. The two cable clamp retainer screws should now be tightened to secure the housing to the microphone cord. If the cutting directions have been carefully followed, the cable clamp should secure to the insulating jacket of the microphone cable. 8. Upon completion of the microphone plug wiring, connect and secure the microphone plug in the transceiver. 0
SPECIFICATIONS GENERAL Channels 40 CH/AM/FM/USB/LSB Frequency Range 26.965 ÷ 27.405 Frequency Control Phase Lock Loop (PLL) synthesizer Frequency Tolerance 0.005 Frequency Stability 0.00 % Operating Temperature Range - 0° C to + 55° C Microphone Plug-in dynamic with push-to-talk switch and coiled cord Input Voltage 3.8 V DC nominal, ± 0% Current consumption Transmitter: FM full mod., 4A -SSB PEP output, 4A Receiver: Squelched, 0.6A -Maximum audio output, .2A Size 6 cm (H) x 20 cm (W) x 23.5 cm(D) Weight 2.250 Kg Antenna Connector UHF, SO 239 Meter (3-in- ) Illuminated; indicates relative output power, received signal strength and SWR. Duty cycle 5/5/90 TRANSMITTER Power Output SSB: 4 W - FM: 4W - AM: W Modulation AM/FM/SSB Intermodulation SSB 3rd order, more than -25 dB Distortion 5th order, more than -35 dB SSB Carrier Suppression 55 dB Unwanted Sideband 50 dB Frequency Response AM and FM: 300 Hz to 3000 Hz Output Impedance 50 Ohms, unbalanced Output Indicators Meter shows relative RF output power and SWR. Transmit LED glows red when trasmitter is working RECEIVER Sensitivity SSB: 0.25 µV for 0 dB (S+N)/N AM: 0.6 µV for 20 dB (S+N)/N FM: 0.6 µV for 20 dB (S+N)/N IF Frequency AM/FM: 0.695 MHz st IF, 455 kHZ 2nd IF - SSB: 0.695 MHz Adjacent-Channel Rejection 60 dB AM/FM & 70 dB SSB RF Gain Control 45 dB adjustable for optimum signal reception Automatic Gain Control (AGC) Less than 0 dB change in audio output for inputs from 0 to 00.000 microvolts Squelch Adjustable; thereshold less than 0.5 µV ANL Switchable Clarifier Range Coarse (RX) ±5 KHz; Fine (RX) ± KHz Audio Output Power 4 watts into 8 ohms Frequency Response 300 ÷ 3 KHz Built-in Speaker 8 ohms, round External Speaker (Not Supplied) 8 ohms; disables internal speaker when connected E N G L I S H
Page 1: ALAN 8001S EURO
Page 4 and 5: I T A L I A N O INSTALLAZIONE POSIZ
Page 6 and 7: I T A L I A N O ALTOPARLANTE ESTERN
Page 8 and 9: I T A L I A N O 21. DISPLAY FREQUEN
Page 10 and 11: I T A L I A N O riproduzione uguale
Page 12 and 13: I T A L I A N O 3 2 4 1 FIG. 4. Num
Page 15 and 16: TABLE OF CONTENTS Installation ....
Page 17 and 18: direction of the body of the vehicl
Page 19 and 20: properly adjusted and matched to yo
Page 21 and 22: RECEIVING SSB SIGNALS There are fou
Page 23: If the microphone to be used is pro
Page 28 and 29: D E U T S C H AM-FM-SSB Transceiver
Page 30 and 31: D E U T S C H 18. NB/ANL-OFF SCHALT
Page 32 and 33: D E U T S C H (LSB) gehört wird ,
Page 34 and 35: D E U T S C H Wenn das verwendete M
Page 36 and 37: D E U T S C H TECHNISCHE DATEN ALLG
Page 38 and 39: E S P A Ñ O L INSTALACIÓN Planifi
Page 40 and 41: E S P A Ñ O L la pieza con unos al
Page 42 and 43: E S P A Ñ O L ajuste el indicador
Page 44 and 45: E S P A Ñ O L 6. Coloque los contr
Page 46 and 47: E S P A Ñ O L Medición de la ROE
Page 48 and 49: E S P A Ñ O L 6. Asegúrese de que
Page 50 and 51: E S P A Ñ O L CTE International SR
Page 52 and 53: F R A N Ç A I S INSTALLATION Empla
Page 54 and 55: F R A N Ç A I S Haut-parleur.exter
Page 56 and 57: F R A N Ç A I S 20.. NON.UTILISE.
Page 58 and 59: F R A N Ç A I S Roger.Beep Quand v
Page 60 and 61: F R A N Ç A I S 3 2 4 1 Fig 4.Pris
Page 63 and 64: ÍNDICE Instalação...............
Page 65 and 66: distâncias. O emissor-receptor inc
Page 67 and 68: 5. SWR CAL CONTROL (CONTROLO DE CAL
Page 69 and 70: 6. Ajuste o interruptor CHANNEL (ca
Page 71 and 72: Fig. 2. Esquema do microfone do seu
Page 73: ESPECIFICAÇÕES GERAL Canais 40 CH
Page 76 and 77:
Ε Λ Λ Η Ν Ι Κ Α ΕΓΚΑΤ
Page 78 and 79:
Ε Λ Λ Η Ν Ι Κ Α κατά τ
Page 80 and 81:
Ε Λ Λ Η Ν Ι Κ Α 18. ΔΙΑ
Page 82 and 83:
Ε Λ Λ Η Ν Ι Κ Α ΕΝΑΛΛ
Page 84 and 85:
Ε Λ Λ Η Ν Ι Κ Α Βεβαι
Page 86:
Schema elettrico - Electric diagram
Page 89:
Schema a blocchi - Block diagram -
show all

ALAN 8001S EURO

Create successful ePaper yourself

Delete template?

Save as template?