3 Other operating modes of the G-18.mft - NRI

More documents

Recommendations

Info

TECHNICAL DATA G-18.mft with vending machine control system Accessories To adapt the coin validator to suit your individual needs, you can acquire the following accessories from NRI: Configuration software To enable you to react as quickly as possible to new false coins in circulation at the workshop or on site at the vending machine and to enable you to make your individual settings, the coin validator can be connected to: • The NRI PC programming station consisting of: – Configuration and diagnostics software "WinEMP”, including card reader and chip card (ordering code 20119 for basic module and 20166 for data block download additional module) – either: Tester G-19.0594/4 for mains voltage of 230 V (ordering code 11801) or Tester G-19.0651 for mains voltage of 115 V (ordering code 21410) or: Tester G-19.0654 (ordering code 24257) and 24-V DC power pack (ordering code 24684) and power cable with Euro plug (ordering code 24683) or with USA plug (ordering code 24853) or power cable with Euro plug and international adapter (ordering code 24683 and 22502) as well as a connecting cable (ordering code 23627) The tester mentioned last is still being modified for the connection to the G-18.mft, but it also provides the option of being able to connect to the WinMDB PC test station (see separate WinMDB instructions). • NRI Palm application "PalmEMP” (freeware on NRI homepage) To be able to connect a Palm handheld m125 and higher to the coin validator, you need a dongle with the ordering code 23760; for an m105, a dongle with the ordering code 23761. If you wish to perform data block downloads with the help of a Palm handheld, you need the WinEMP software (see above) with PalmEMP download rights (ordering code 23649), which are stored on the WinEMP chip card. You can also connect the Palm handheld via the universal dongle with a 9-pole D-SUB plug (ordering code 23764). However, the Palm handheld must then be equipped with an interface that can be connected to the serial HotSync cable (available from Palm TM ). For details regarding which settings can be made with the help of WinEMP and PalmEMP, please see Chap. 9 "Which functions can be set using WinEMP/PalmEMP?”. For details on how to carry out these settings, please refer to the separate software instructions. 52 National Rejectors, Inc. GmbH, Buxtehude
G-18.mft with vending machine control system TECHNICAL DATA Update software The coin validator is equipped with a microprocessor including a flash memory. This allows the coin validator operating software to be updated quickly and without complications. In order to load new operating software in the coin validator, you need one of the following alternatives (current operating software available on request): • NRI PC update station for the workshop, consisting of: – software "WinFlash” (ordering code 21524) – tester G-19.0641 for voltage supply of the coin validator (ordering code 12922) – programming adapter G-19.0649 (ordering code 20308) • NRI update solution for on-site programming, consisting of: – PC software "WinFlash” (ordering code 21524) in order to load the current firmware from the hard disk of your PC into the flash prommer – mobile Flash-Prommer G-55.0350 (ordering code 20308) For details on how to install and apply WinFlash and flash prommer, please refer to the respective separate instructions. GeldKarte card reader and display If the vending machine is to be converted to coin and card operation, the coin validator can also take over control of the following MDB periphery in addition to controlling the vending machine functions: • MDB GeldKarte card reader – G-55.8417 "compact module” or (ordering code differs depending on each model and must be requested from NRI) – G-55.8497 "modular design" (ordering code differs depending on each model and must be requested from NRI) • MDB display (ordering code 24030) The MDB periphery is connected using an MDB cable set (ordering code 24026). National Rejectors, Inc. GmbH, Buxtehude 53
Page 1: Technical Documentation 01.06 GS/Bu
Page 4 and 5: TABLE OF CONTENTS G-18.mft with ven
Page 7 and 8: G-18.mft with vending machine contr
Page 51: G-18.mft with vending machine contr

3 Other operating modes of the G-18.mft - NRI

Create successful ePaper yourself

Delete template?

Save as template?