3 Other operating modes of the G-18.mft - NRI
3 Other operating modes of the G-18.mft - NRI 3 Other operating modes of the G-18.mft - NRI
STARTING UP G-18.mft with vending machine control system Set exact price or overpay mode 1 De-energize the coin validator and remove from the vending machine. 2 Set the DIL switch 7 of the upper switching block S1 on the rear of the device upward to ON for "exact price" or downward (to OFF) for "overpay". "Exact price" activated "Overpay" activated 3 Hang the coin validator back in the machine again and supply with voltage. 32 National Rejectors, Inc. GmbH, Buxtehude
G-18.mft with vending machine control system STARTING UP Connecting the device environment of the PC programming station (WinEMP) If you want the G-18.mft to be set on the PC using the diagnostics and configuration software WinEMP, the following device environment is connected to the PCB direct plug 5 of the coin validator (see Fig. 2a and section "Accessories" in Chap. 10 "Technical data"): • Tester for voltage supply • WinEMP card reader incl. chip card National Rejectors, Inc. GmbH, Buxtehude Fig. 3: Device environment for WinEMP For details on how to connect the device environment to your PC and how to operate the software, please refer to the separate documentation for the WinEMP software (refer also to Chap. 9 "Which functions can be set using WinEMP/PalmEMP?"). Prior to making the connection to the programming station, the DIL switch S3.9 on the rear of the coin validator must be set upward to ON first, since otherwise it will not be possible to set up a connection to the PC. The WinEMP functions that are relevant for the vending machine control system of the G-18.mft are currently being revised. Connecting the Palm handheld (PalmEMP) "PalmEMP" is an NRI program that can be installed as an additional application on a Palm handheld. Simply use the appropriate dongle to connect the Palm handheld to the PCB direct plug 5 of the coin validator (see Fig. 2a and section "Accessories" in Chap. 10 "Technical data"). The coin validator remains installed in the vending machine. The PalmEMP functions that are relevant for the vending machine control system of the G-18.mft are currently being revised. 33
- Page 1: Technical Documentation 01.06 GS/Bu
- Page 4 and 5: TABLE OF CONTENTS G-18.mft with ven
- Page 7 and 8: G-18.mft with vending machine contr
- Page 9 and 10: G-18.mft with vending machine contr
- Page 11 and 12: G-18.mft with vending machine contr
- Page 13 and 14: G-18.mft with vending machine contr
- Page 15 and 16: G-18.mft with vending machine contr
- Page 17 and 18: G-18.mft with vending machine contr
- Page 19 and 20: G-18.mft with vending machine contr
- Page 21 and 22: G-18.mft with vending machine contr
- Page 23 and 24: G-18.mft with vending machine contr
- Page 25 and 26: G-18.mft with vending machine contr
- Page 27 and 28: G-18.mft with vending machine contr
- Page 29 and 30: G-18.mft with vending machine contr
- Page 31: G-18.mft with vending machine contr
- Page 35 and 36: G-18.mft with vending machine contr
- Page 37 and 38: G-18.mft with vending machine contr
- Page 39 and 40: G-18.mft with vending machine contr
- Page 41 and 42: G-18.mft with vending machine contr
- Page 43 and 44: G-18.mft with vending machine contr
- Page 45 and 46: G-18.mft with vending machine contr
- Page 47 and 48: G-18.mft with vending machine contr
- Page 49 and 50: G-18.mft with vending machine contr
- Page 51 and 52: G-18.mft with vending machine contr
- Page 53 and 54: G-18.mft with vending machine contr
- Page 55 and 56: G-18.mft with vending machine contr
- Page 57 and 58: G-18.mft with vending machine contr
- Page 59 and 60: G-18.mft with vending machine contr
G-<strong>18.mft</strong> with vending machine control system STARTING UP<br />
Connecting <strong>the</strong> device environment <strong>of</strong> <strong>the</strong><br />
PC programming station (WinEMP)<br />
If you want <strong>the</strong> G-<strong>18.mft</strong> to be set on <strong>the</strong> PC using <strong>the</strong> diagnostics and<br />
configuration s<strong>of</strong>tware WinEMP, <strong>the</strong> following device environment is<br />
connected to <strong>the</strong> PCB direct plug 5 <strong>of</strong> <strong>the</strong> coin validator (see Fig. 2a and<br />
section "Accessories" in Chap. 10 "Technical data"):<br />
• Tester for voltage supply<br />
• WinEMP card reader incl. chip card<br />
National Rejectors, Inc. GmbH, Buxtehude<br />
Fig. 3: Device environment for WinEMP<br />
For details on how to connect <strong>the</strong> device environment to your PC and how<br />
to operate <strong>the</strong> s<strong>of</strong>tware, please refer to <strong>the</strong> separate documentation for <strong>the</strong><br />
WinEMP s<strong>of</strong>tware (refer also to Chap. 9 "Which functions can be set using<br />
WinEMP/PalmEMP?").<br />
Prior to making <strong>the</strong> connection to <strong>the</strong> programming station,<br />
<strong>the</strong> DIL switch S3.9 on <strong>the</strong> rear <strong>of</strong> <strong>the</strong> coin validator must be<br />
set upward to ON first, since o<strong>the</strong>rwise it will not be possible<br />
to set up a connection to <strong>the</strong> PC.<br />
The WinEMP functions that are relevant for <strong>the</strong> vending machine<br />
control system <strong>of</strong> <strong>the</strong> G-<strong>18.mft</strong> are currently being revised.<br />
Connecting <strong>the</strong> Palm handheld (PalmEMP)<br />
"PalmEMP" is an <strong>NRI</strong> program<br />
that can be installed as an<br />
additional application on a<br />
Palm handheld. Simply use <strong>the</strong><br />
appropriate dongle to connect<br />
<strong>the</strong> Palm handheld to <strong>the</strong> PCB<br />
direct plug 5 <strong>of</strong> <strong>the</strong> coin validator<br />
(see Fig. 2a and section<br />
"Accessories" in Chap. 10<br />
"Technical data"). The coin<br />
validator remains installed in<br />
<strong>the</strong> vending machine.<br />
The PalmEMP<br />
functions that are<br />
relevant for <strong>the</strong> vending machine control system <strong>of</strong> <strong>the</strong> G-<strong>18.mft</strong> are<br />
currently being revised.<br />
33