Kuhnke Electronics Instruction Manual
Kuhnke Electronics Instruction Manual Kuhnke Electronics Instruction Manual
Hardware 3.4.4 Analogue Outputs Ventura Remote PLC has 2 analogue outputs labelled ao0, and ao1. They are set by the configuration. Their resolution can be set to either 8 bit (10V/256, i.e. approx. 39mV) or 10 bit (10V/1024, i.e. approx. 96mV). They attach to the screw-type locking terminal. Immediately next to the analogue input, there is a terminal for the analogue reference potential. All analogue reference potential terminals are interconnected. ao 1 0 Signal pin wiring The screw-type locking terminals are safe for use with conductors of a diameter between 0.25 mm 2 and 1.5 mm 2 . To avoid noise on the operative signal, you are advised to use shielded cables. Attach the shield to the earth conductor terminals on the left side wall. 40 E 700 GB
3.5 A, B, Ref Counter Hardware Ventura Remote PLC features a connector for a 24 V incremental encoder which can be used either as A, B, Ref counter or as an event counter. Its actual function is set at the configuration stage. To connect, attach a 9-pin male Sub-D connector to the female Sub-D Encoder port on the unit. Signal pin wiring encoder 9 8 7 6 5 4 3 2 1 Pin 1 Gnd Pin 2 reference input Pin 3 counter input B Pin 4 counter input A Pin 5 +24V Housing frame ground (cable shield) 41
- Page 1 and 2: Kuhnke Electronics Instruction Manu
- Page 3 and 4: Table of Contents Introduction 1 In
- Page 5 and 6: Introduction 4.3.4 PLC Configuratio
- Page 7 and 8: Introduction 6.1.4 Station Address
- Page 9 and 10: 1 Introduction Introduction Ventura
- Page 11 and 12: 1.2 Variants Introduction Compact c
- Page 13 and 14: Advantages of Decentralisation Intr
- Page 15 and 16: 1.5 Network Examples 1.5.1 PROFIBUS
- Page 17 and 18: 2 Reliability, Safety 2.1 Intended
- Page 19 and 20: 2.4.3 Note Reliability, Safety This
- Page 21 and 22: 2.5.1 Project Planning and Installa
- Page 23 and 24: 2.6 Electromagnetic Compatibility 2
- Page 25 and 26: 2.6.6.2 Contamination Reliability,
- Page 27 and 28: 3 Hardware 3.1 System Description H
- Page 29 and 30: Hardware Extensions Ventura Remote
- Page 31 and 32: 3.3 Power Supply 3.3.1 Earth left s
- Page 33 and 34: 3.3.3 Power Supply Hardware Voltage
- Page 35 and 36: 3.4 Inputs and Outputs 3.4.1 Digita
- Page 37 and 38: 3.4.2 Digital Combi I/Os Hardware V
- Page 39: 3.4.3 Analogue Inputs Hardware Vent
- Page 43 and 44: 3.6.2 PROFIBUS Hardware Ventura Rem
- Page 45 and 46: 3.7 Expansion Modules Ventura Remot
- Page 47 and 48: 3.8.2 Mode Selector mode selector H
- Page 49 and 50: 3.8.3.1 RUN 3.8.3.2 Stop 3.8.3.3 Ex
- Page 51 and 52: 3.9 Status and Failure Indication "
- Page 53 and 54: Installation 4 PLC Functions of Ven
- Page 55 and 56: 4.2 Writing CoDeSys Programs Online
- Page 57 and 58: 4.2.2 CAN: Online CAN Function Libr
- Page 59 and 60: 4.3.1 Operating System Function Lib
- Page 61 and 62: 4.3.3 Task Configuration 4.3.3.1 PL
- Page 63 and 64: 4.3.3.2 The Task Configurator 4.3.3
- Page 65 and 66: 4.3.4 PLC Configuration Function Li
- Page 67 and 68: Function Libraries DI16/DO16". Repe
- Page 69 and 70: 4.3.6 The Flash File System Functio
- Page 71 and 72: 4.4.1 Installing a Thread Function
- Page 73 and 74: Thread usage Function Libraries A t
- Page 75 and 76: 4.4.2 Installing / Uninstalling a T
- Page 77 and 78: To uninstall a timer task: Function
- Page 79 and 80: 4.4.3 Enabling / Disabling the Outp
- Page 81 and 82: 4.4.5 Direct Write of Local Outputs
- Page 83 and 84: FUNCTION INSTALL_ERROR_IRQ : BOOL V
- Page 85 and 86: Function Libraries INSTALL_INPUT_IR
- Page 87 and 88: 4.4.8 Installing a REF IRQ Module F
- Page 89 and 90: 4.4.10 Setting up the Watchdog Func
3.5 A, B, Ref Counter<br />
Hardware<br />
Ventura Remote PLC features a connector for a 24 V<br />
incremental encoder which can be used either as A, B,<br />
Ref counter or as an event counter. Its actual function is<br />
set at the configuration stage. To connect, attach a 9-pin<br />
male Sub-D connector to the female Sub-D Encoder port<br />
on the unit.<br />
Signal pin wiring<br />
encoder<br />
9<br />
8<br />
7<br />
6<br />
5<br />
4<br />
3<br />
2<br />
1<br />
Pin 1 Gnd<br />
Pin 2 reference input<br />
Pin 3 counter input B<br />
Pin 4 counter input A<br />
Pin 5 +24V<br />
Housing frame ground (cable<br />
shield)<br />
41