Kuhnke Electronics Instruction Manual
Kuhnke Electronics Instruction Manual Kuhnke Electronics Instruction Manual
Error Handling The relevant information is found at: SYSTEMINFO Value Explanation Error Byte Operating mode (Betriebsart) Bit 0 Short circuit Bit 1 Supply voltage low Bit 2 not used Bit 3 not used Bit 4 not used Bit 5 Watchdog Bit 6..7 0 Run not used 1 Stop Byte 19 Reset ExtError WORD noofT3Error WORD Bit 0 TimerTaskTimer overflow Bit 1 TimerTask does not exist Bit2..7 not used TimerTasks error counter 178 E 700 GB
Example VAR C690_Error: BYTE; END_VAR C690_Error:=SYSTEMINFO.Error; Error Handling The following sections describe the types of faults and suggest handling and corrective actions. 179
- Page 127 and 128: Internal combi I/Os %IX0.0-%IX0.3 a
- Page 129 and 130: Internal I/Os AI_x and AO_x I/O Var
- Page 131 and 132: Software If an "Input IRQ module" h
- Page 133 and 134: 5.3.3 Functions of Internal Outputs
- Page 135 and 136: Software Value Frequency Value Freq
- Page 137 and 138: 5.3.4 Short-circuited Output Softwa
- Page 139 and 140: 5.3.5 Internal Analogue Input Funct
- Page 141 and 142: 5.3.6 Internal Analogue Output Func
- Page 143 and 144: 5.3.7 Functions of Internal Counter
- Page 145 and 146: 5.3.7.1.2 Event Counter Variables V
- Page 147 and 148: Resolution of the rotary encoder: s
- Page 149 and 150: Software 5.4 Functions of the Basic
- Page 151 and 152: 5.7 Status Messages of Expansion Mo
- Page 153 and 154: 6 PROFIBUS-DP 6.1 Basic Information
- Page 155 and 156: 6.2 Master-Slave Communication PROF
- Page 157 and 158: 6.2.2 Receive Parameter Data (Prm_D
- Page 159 and 160: 6.2.2.2 Device-specific Bus Paramet
- Page 161 and 162: PROFIBUS replaces the term "byte" w
- Page 163 and 164: Octet 4: Diag.Master_Add PROFIBUS A
- Page 165 and 166: 6.2.4 Master-Slave Data Communicati
- Page 167 and 168: Example: VAR bIn_0: BYTE; bOut_0: B
- Page 169 and 170: 7 CANopen CANopen At this point, we
- Page 171 and 172: 7.1.1 CANopen Example CANopen A Ven
- Page 173 and 174: • Step3: Write and test CoDeSys p
- Page 175 and 176: PROGRAM PLC_PRG VAR CANMaster_Ok: B
- Page 177: 8 PLC Error Handling 8.1 "Failure"
- Page 181 and 182: 8.3.1 Short-circuited Output (Error
- Page 183 and 184: => - STOP: The program is stopped E
- Page 185 and 186: 9 Appendix 9.1 Technical Data 9.1.1
- Page 187 and 188: Appendix Max. current .............
- Page 189 and 190: 9.1.3 Communication Ports V.24 port
- Page 191 and 192: 9.2 Order Specifications 9.2.1 Cont
- Page 193 and 194: Appendix 9.3 Ventura Remote I/O Exp
- Page 195 and 196: 9.5 Sales & Service Appendix Please
- Page 197 and 198: 9.6 Index A, B, Ref counter 146 con
- Page 199: PROFIBUS port 43 PROFIBUS-DP 153 di
Error Handling<br />
The relevant information is found at:<br />
SYSTEMINFO Value Explanation<br />
Error<br />
Byte<br />
Operating mode<br />
(Betriebsart)<br />
Bit 0 Short circuit<br />
Bit 1 Supply voltage low<br />
Bit 2 not used<br />
Bit 3 not used<br />
Bit 4 not used<br />
Bit 5 Watchdog<br />
Bit<br />
6..7<br />
0 Run<br />
not used<br />
1 Stop<br />
Byte 19 Reset<br />
ExtError<br />
WORD<br />
noofT3Error<br />
WORD<br />
Bit 0 TimerTaskTimer overflow<br />
Bit 1 TimerTask does not exist<br />
Bit2..7 not used<br />
TimerTasks error counter<br />
178 E 700 GB
Change language