Fuxx Control - ARS 2320 / ARS 2340 Instruction Manual - Kuhnke
Fuxx Control - ARS 2320 / ARS 2340 Instruction Manual - Kuhnke Fuxx Control - ARS 2320 / ARS 2340 Instruction Manual - Kuhnke
Fuxx Control ARS 2320 / ARS 2340 KUHNKE Automation 8.4.10 Connection notes concerning [X9A] at the ARS 2340 Braking resistor connector BR-EXT BR-CH BR-INT External braking resistor Alternative ! Figure 20: Pin assignment [X9A] at the ARS 2340: Braking resistor PHOENIX Power- Combicon at X9 8.5 Connection: Safe standstill and 24V supply [X3] The "safe stop" option in accordance with EN 954-1, category 3, can be activated using the safe standstill connector [X3] and an external circuit. The 24VDC supply is also connected using the 24V supply connector [X3]. 8.5.1 Configuration on the device [X3] � PHOENIX Mini-Combicon MC 1.5/6-STF-3.81 8.5.2 Mating connector [X3] � PHOENIX Mini-Combicon MC 1.5/ 6-GF-3.81 84 E 732 GB 14.12.2006 1 2 3
KUHNKE Automation Fuxx Control ARS 2320 / ARS 2340 8.5.3 Pin assignment [X3] Table 31: Pin assignment [X3] Pin no. Name Value Specification 1 24V 24VDC / 2.8 A 24VDC supply for control section (0.8A) and holding brake (2A) (Without safety measures in accordance with category 3: Bridge pin 1 and 2) 2 REL 0VDC / 24VDC Setting and resetting of the relay for interrupting the driver supply 3 0V GND 24 VDC Reference potential for the 24VDC supply and the PLC 4 ERR 0V / 24VDC Signaling contact "Error on safety module" 5 NC1 6 NC2 250VAC max. switching voltage Floating response contact of driver supply, normally closed contact 8.5.4 Cable type and configuration: 24VDC power supply [X3] The cable names given refer to cables made by Lapp. They have proven to be reliable and are successfully used in many applications. However, it is also possible to use comparable cables from other manufacturers, e.g. Lütze or Helukabel. For 24 VAC power supply: � LAPP KABEL ÖLFLEX-CLASSIC 110; 2 x 1 mm² 8.5.5 Connection notes [X3] Braking resistor connector 24 VDC supply 1 Without category 3 safety equipment: 2 Bridge between pin 1 and 2 GND 24 VDC 3 4 5 6 Figure 21: Pin assignment [X3]: 24VDC power supply PHOENIX MINI COMBICON at X3 E 732 GB 85 14.12.2006
- Page 33 and 34: KUHNKE Automation Fuxx Control ARS
- Page 35 and 36: KUHNKE Automation Fuxx Control ARS
- Page 37 and 38: KUHNKE Automation Fuxx Control ARS
- Page 39 and 40: KUHNKE Automation Fuxx Control ARS
- Page 41 and 42: KUHNKE Automation Fuxx Control ARS
- Page 43 and 44: KUHNKE Automation Fuxx Control ARS
- Page 45 and 46: KUHNKE Automation Fuxx Control ARS
- Page 47 and 48: KUHNKE Automation Fuxx Control ARS
- Page 49 and 50: KUHNKE Automation Fuxx Control ARS
- Page 51 and 52: KUHNKE Automation Fuxx Control ARS
- Page 53 and 54: KUHNKE Automation Fuxx Control ARS
- Page 55 and 56: KUHNKE Automation Fuxx Control ARS
- Page 57 and 58: KUHNKE Automation Fuxx Control ARS
- Page 59 and 60: KUHNKE Automation Fuxx Control ARS
- Page 61 and 62: KUHNKE Automation Fuxx Control ARS
- Page 63 and 64: KUHNKE Automation Fuxx Control ARS
- Page 65 and 66: KUHNKE Automation Fuxx Control ARS
- Page 67 and 68: KUHNKE Automation Fuxx Control ARS
- Page 69 and 70: KUHNKE Automation Fuxx Control ARS
- Page 71 and 72: KUHNKE Automation Fuxx Control ARS
- Page 73 and 74: KUHNKE Automation Fuxx Control ARS
- Page 75 and 76: KUHNKE Automation Fuxx Control ARS
- Page 77 and 78: KUHNKE Automation Fuxx Control ARS
- Page 79 and 80: KUHNKE Automation Fuxx Control ARS
- Page 81 and 82: KUHNKE Automation Fuxx Control ARS
- Page 83: KUHNKE Automation Fuxx Control ARS
- Page 87 and 88: KUHNKE Automation Fuxx Control ARS
- Page 89 and 90: KUHNKE Automation Fuxx Control ARS
- Page 91 and 92: KUHNKE Automation Fuxx Control ARS
- Page 93 and 94: KUHNKE Automation Fuxx Control ARS
- Page 95 and 96: KUHNKE Automation Fuxx Control ARS
- Page 97 and 98: KUHNKE Automation Fuxx Control ARS
- Page 99 and 100: KUHNKE Automation Fuxx Control ARS
- Page 101 and 102: KUHNKE Automation Fuxx Control ARS
- Page 103 and 104: KUHNKE Automation Fuxx Control ARS
- Page 105 and 106: KUHNKE Automation Fuxx Control ARS
- Page 107 and 108: KUHNKE Automation Fuxx Control ARS
- Page 109 and 110: KUHNKE Automation Fuxx Control ARS
- Page 111 and 112: KUHNKE Automation Fuxx Control ARS
- Page 113 and 114: KUHNKE Automation Fuxx Control ARS
- Page 115 and 116: KUHNKE Automation Fuxx Control ARS
- Page 117 and 118: KUHNKE Automation Fuxx Control ARS
- Page 119 and 120: KUHNKE Automation Fuxx Control ARS
- Page 121 and 122: KUHNKE Automation Fuxx Control ARS
- Page 123 and 124: KUHNKE Automation Fuxx Control ARS
- Page 125 and 126: KUHNKE Automation Fuxx Control ARS
- Page 127 and 128: KUHNKE Automation Fuxx Control ARS
- Page 129 and 130: KUHNKE Automation Fuxx Control ARS
- Page 131 and 132: KUHNKE Automation Fuxx Control ARS
- Page 133 and 134: KUHNKE Automation Fuxx Control ARS
KUHNKE Automation <strong>Fuxx</strong> <strong>Control</strong> <strong>ARS</strong> <strong>2320</strong> / <strong>ARS</strong> <strong>2340</strong><br />
8.5.3 Pin assignment [X3]<br />
Table 31: Pin assignment [X3]<br />
Pin<br />
no.<br />
Name Value Specification<br />
1 24V 24VDC / 2.8 A 24VDC supply for control section (0.8A) and holding brake<br />
(2A)<br />
(Without safety measures in accordance with category 3: Bridge<br />
pin 1 and 2)<br />
2 REL 0VDC / 24VDC Setting and resetting of the relay for interrupting the driver<br />
supply<br />
3 0V GND 24 VDC Reference potential for the 24VDC supply and the PLC<br />
4 ERR 0V / 24VDC Signaling contact "Error on safety module"<br />
5 NC1<br />
6 NC2<br />
250VAC max.<br />
switching<br />
voltage<br />
Floating response contact of driver supply, normally closed<br />
contact<br />
8.5.4 Cable type and configuration: 24VDC power supply [X3]<br />
The cable names given refer to cables made by Lapp. They have proven to be reliable and are<br />
successfully used in many applications. However, it is also possible to use comparable cables from<br />
other manufacturers, e.g. Lütze or Helukabel.<br />
For 24 VAC power supply:<br />
� LAPP KABEL ÖLFLEX-CLASSIC 110; 2 x 1 mm²<br />
8.5.5 Connection notes [X3]<br />
Braking resistor<br />
connector<br />
24 VDC supply 1<br />
Without category 3 safety equipment:<br />
2<br />
Bridge between pin 1 and 2<br />
GND 24 VDC<br />
3<br />
4<br />
5<br />
6<br />
Figure 21: Pin assignment [X3]: 24VDC power supply<br />
PHOENIX MINI<br />
COMBICON at X3<br />
E 732 GB 85<br />
14.12.2006