Fuxx Control - ARS 2320 / ARS 2340 Instruction Manual - Kuhnke
Fuxx Control - ARS 2320 / ARS 2340 Instruction Manual - Kuhnke Fuxx Control - ARS 2320 / ARS 2340 Instruction Manual - Kuhnke
Fuxx Control ARS 2320 / ARS 2340 KUHNKE Automation 11.4 General installation notes for technology modules DANGER ! Prior to installing technology modules, the ARS 2300 servo positioning controller has to be disconnected from any current-carrying conductors. After the operating voltage has been disconnected, wait for 5 minutes so that the capacities in the ARS 2300 servo positioning controller can be completely discharged. Make sure that ESD protection measures are taken when handling technology modules. Remove the front plate above the technology slot of the ARS 2300 servo positioning controller using a suitable screwdriver. Then push the technology module into the open technology slot such that the circuit board is held by the lateral guides of the technology slot. Push the technology module in until it reaches the stop. Then screw technology module onto the housing of the servo positioning controller using the Phillips screw. Make sure that the front plate has conducting contact with the housing of the servo positioning controller (PE). 146 E 732 GB 14.12.2006
- Page 95 and 96: KUHNKE Automation Fuxx Control ARS
- Page 97 and 98: KUHNKE Automation Fuxx Control ARS
- Page 99 and 100: KUHNKE Automation Fuxx Control ARS
- Page 101 and 102: KUHNKE Automation Fuxx Control ARS
- Page 103 and 104: KUHNKE Automation Fuxx Control ARS
- Page 105 and 106: KUHNKE Automation Fuxx Control ARS
- Page 107 and 108: KUHNKE Automation Fuxx Control ARS
- Page 109 and 110: KUHNKE Automation Fuxx Control ARS
- Page 111 and 112: KUHNKE Automation Fuxx Control ARS
- Page 113 and 114: KUHNKE Automation Fuxx Control ARS
- Page 115 and 116: KUHNKE Automation Fuxx Control ARS
- Page 117 and 118: KUHNKE Automation Fuxx Control ARS
- Page 119 and 120: KUHNKE Automation Fuxx Control ARS
- Page 121 and 122: KUHNKE Automation Fuxx Control ARS
- Page 123 and 124: KUHNKE Automation Fuxx Control ARS
- Page 125 and 126: KUHNKE Automation Fuxx Control ARS
- Page 127 and 128: KUHNKE Automation Fuxx Control ARS
- Page 129 and 130: KUHNKE Automation Fuxx Control ARS
- Page 131 and 132: KUHNKE Automation Fuxx Control ARS
- Page 133 and 134: KUHNKE Automation Fuxx Control ARS
- Page 135 and 136: KUHNKE Automation Fuxx Control ARS
- Page 137 and 138: KUHNKE Automation Fuxx Control ARS
- Page 139 and 140: KUHNKE Automation Fuxx Control ARS
- Page 141 and 142: KUHNKE Automation Fuxx Control ARS
- Page 143 and 144: KUHNKE Automation Fuxx Control ARS
- Page 145: KUHNKE Automation Fuxx Control ARS
<strong>Fuxx</strong> <strong>Control</strong> <strong>ARS</strong> <strong>2320</strong> / <strong>ARS</strong> <strong>2340</strong> KUHNKE Automation<br />
11.4 General installation notes for technology modules<br />
DANGER !<br />
Prior to installing technology modules, the <strong>ARS</strong> 2300 servo positioning controller has to<br />
be disconnected from any current-carrying conductors. After the operating voltage has<br />
been disconnected, wait for 5 minutes so that the capacities in the <strong>ARS</strong> 2300 servo<br />
positioning controller can be completely discharged.<br />
Make sure that ESD protection measures are taken when handling technology modules.<br />
Remove the front plate above the technology slot of the <strong>ARS</strong> 2300 servo positioning controller using a<br />
suitable screwdriver. Then push the technology module into the open technology slot such that the<br />
circuit board is held by the lateral guides of the technology slot. Push the technology module in until it<br />
reaches the stop. Then screw technology module onto the housing of the servo positioning controller<br />
using the Phillips screw. Make sure that the front plate has conducting contact with the housing of the<br />
servo positioning controller (PE).<br />
146 E 732 GB<br />
14.12.2006