Ventura IPC Instruction Manual pdf - Kuhnke
Ventura IPC Instruction Manual pdf - Kuhnke Ventura IPC Instruction Manual pdf - Kuhnke
Hardware KUHNKE Automation 4.2 Mounting on Top-hat Rail (Ventura IPC 300 / 700) 4.2.1 To Attach the Rail Adapter to the Device • Use screws (2) to attach snap-on adapter (1) to the back of the unit. 4.2.2 To Attach the Device to the Top-hat Rail • Place the device on the upper top-hat rail guide, holding it at a slant. • Tip the device down onto the top-hat rail until the bracket of the adapter snaps onto the bottom top-hat rail guide. 4.2.3 To Remove the Device from the Top-hat Rail • Pull down the strap at the bottom side of the device. Use a flat screwdriver and turn it slightly. • This will unlock the mechanism holding the unit firmly in place on the top-hat rail. • You can now remove the device. 32 E 674 GB 07.03.2007
KUHNKE Automation Software 5 Start-up Various variants of the Ventura industial PC (IPC) are available. For the exact system configuration of your device, please refer to the name plate and the coded part number on it. To allow the BIOS and operating system to properly detect the DVI or CRT monitor at boot-up, we recommend that you attach the monitor prior to attaching the device to the power supply. Danger of damage to the unit! If the device was exposed to condensation, allow it to rest for about 12 hours before you start to use it. 5.1 Installing CoDeSys on the Programming PC 5.1.1 CoDeSys Target Installation To install the CoDeSys software on your programming PC: • Select CoDeSys...exe either from Windows Explorer or via 'Run' from the Windows Start menu. • Run the program. • The CoDeSys installer runs to request your preferred settings and install the application in the target system. To obtain an installation copy of the CoDeSys programming system either ask for the up-to-date CD-ROM 'Software & Information, E 627 D / GB' or browse for www.3s-software.com and find the download page of that company To create a CoDeSys project for target system "Ventura IPC", you must install the Target Support Package (TSP) "VenturaCE_TV.tnf" prior to running the program by running the installer called InstallTarget. A TSP contains all configuration and extension files required to use an application for operating a certain controller (target system). A configuration includes the code generator, the memory layout, the set of functions provided by the controller and the I/O modules. The libraries, gateway drivers, error and ini files for the PLC browser etc. are also installed. • Run the target installer delivered with your CoDeSys package. • Click on "Open" to open the folder containing TSP "KUHNKE PC Control Ventura", then choose "VenturaCE_TV.tnf". • Click to select "KUHNKE PC Control Ventura" and "Install" it. E 674 GB 33 07.03.2007
- Page 1 and 2: Kuhnke Electronics Instruction Manu
- Page 3 and 4: KUHNKE Automation Table of Contents
- Page 5 and 6: KUHNKE Automation Table of Contents
- Page 7 and 8: 1 Introduction Performance in a nut
- Page 9 and 10: KUHNKE Automation Reliability, Safe
- Page 11 and 12: KUHNKE Automation Reliability, Safe
- Page 13 and 14: KUHNKE Automation Hardware 3 Ventur
- Page 15 and 16: KUHNKE Automation Hardware 3.4 Tech
- Page 17 and 18: KUHNKE Automation Hardware 3.6 Phys
- Page 19 and 20: KUHNKE Automation Hardware 3.7.4 Gr
- Page 21 and 22: KUHNKE Automation Hardware 3.7.7 Et
- Page 23 and 24: KUHNKE Automation Hardware 3.9 Stor
- Page 25 and 26: KUHNKE Automation Hardware 3.11 Ext
- Page 27 and 28: KUHNKE Automation Hardware 3.12.4 F
- Page 29 and 30: KUHNKE Automation Hardware 3.13 Ven
- Page 31: KUHNKE Automation Hardware 4 Instal
- Page 35 and 36: KUHNKE Automation Software Windows
- Page 37 and 38: KUHNKE Automation Software 6.1 Comp
- Page 39 and 40: KUHNKE Automation Software 6.2.3 OP
- Page 41 and 42: KUHNKE Automation Software 6.3.3 Ul
- Page 43 and 44: KUHNKE Automation Software 6.5 Vent
- Page 45 and 46: KUHNKE Automation Software 7.1.2 Co
- Page 47 and 48: KUHNKE Automation Software 7.1.5 OP
- Page 49 and 50: KUHNKE Automation Software • Deve
- Page 51 and 52: KUHNKE Automation Software This com
- Page 53 and 54: KUHNKE Automation Software Sometime
- Page 55 and 56: KUHNKE Automation Software 7.5 Conn
- Page 57 and 58: KUHNKE Automation Software 7.5.2 Et
- Page 59 and 60: KUHNKE Automation Software • Star
- Page 61 and 62: KUHNKE Automation Software 9 Mainte
- Page 63 and 64: KUHNKE Automation Appendix 10 Appen
- Page 65 and 66: KUHNKE Automation Appendix E 674 GB
- Page 67 and 68: KUHNKE Automation Appendix Max. pow
- Page 69 and 70: KUHNKE Automation Appendix 10.3 Dim
- Page 71 and 72: KUHNKE Automation Appendix 10.3.3 V
- Page 73 and 74: KUHNKE Automation Appendix 10.4 Ven
- Page 75 and 76: KUHNKE Automation Appendix 10.4.2 V
- Page 77 and 78: KUHNKE Automation Appendix 10.4.4 O
- Page 79 and 80: KUHNKE Automation Appendix 10.4.6 E
- Page 81 and 82: KUHNKE Automation Appendix 10.7.2 A
Hardware KUHNKE Automation<br />
4.2 Mounting on Top-hat Rail (<strong>Ventura</strong> <strong>IPC</strong> 300 / 700)<br />
4.2.1 To Attach the Rail Adapter to the Device<br />
• Use screws (2) to attach snap-on adapter (1) to the back of the unit.<br />
4.2.2 To Attach the Device to the Top-hat Rail<br />
• Place the device on the upper top-hat rail guide, holding it at a slant.<br />
• Tip the device down onto the top-hat rail until the bracket of the adapter<br />
snaps onto the bottom top-hat rail guide.<br />
4.2.3 To Remove the Device from the Top-hat Rail<br />
• Pull down the strap at the bottom side of the device. Use a flat screwdriver<br />
and turn it slightly.<br />
• This will unlock the mechanism holding the unit firmly in place on the<br />
top-hat rail.<br />
• You can now remove the device.<br />
32 E 674 GB<br />
07.03.2007
Change language