Ventura IPC Instruction Manual pdf - Kuhnke
Ventura IPC Instruction Manual pdf - Kuhnke Ventura IPC Instruction Manual pdf - Kuhnke
Hardware KUHNKE Automation 3.7 Ventura IPC Power Supply and Ports 3.7.1 24 VDC Power Supply 3.7.2 Operative Earth 3.7.3 Serial Ports "COM1 and COM2" 1 6 2 7 3 8 4 9 5 Only attach the unit to a 24 VDC power supply source if the source is guaranteed to meet safe extra low voltage requirements (SELV). Please use the connector from the package to attach the unit to the power supply. The admissible diameter of the cord connecting the 24 VDC power is between 0.75 mm 2 and 2.5 mm 2 . Connector 2-pin, male, 2.5 mm 2 Pin Function L+ Supply voltage +24 VDC L GND Connect operative earth to the protective earth conductor of the switching cabinet or the system that the PC is installed in. Use the flat plug (6.3 mm x 0.8 mm) on the bottom side of the unit. The minimum cross section must be no less than 2.5 mm 2 . Try to keep the lead to the cabinet terminal as short as possible. A low-impedance earth conductor improves the dissipation of interference received via external power supply cables, signal cables or cables of peripheral units. Ventura IPC has two serial COM ports for communication with peripherals such as terminals, modems, etc. A 9-pin D-Sub connector is used to attach peripherals with a suitable cable. Connector 9-pin D-SUB, male Pin Function 1 - 2 TxD 3 RxD 4 - 5 GND 6 - 7 CTS 8 RTS 9 - 18 E 674 GB 07.03.2007
KUHNKE Automation Hardware 3.7.4 Graphics Adapter "DVI / VGA" The DVI-I adapter transfers analogue and digital monitor data (DVI-I integrated, analogue and digital) and can therefore be used for both monitors with a digital DVI port and monitors with an analogue VGA input. If a Ventura IPC touch-series monitor is attached, the cable can be up to 25 m long (800x600 resolution). To bridge larger gaps, a DVI signal repeater can be installed somewhere along the line. Since the DVI port outputs VGA signals, VGA monitors can be attached using a DVI-to-VGA adapter. Pin Signal Function 1 TMDS Data2- DVI data line (A) 2 TMDS Data2+ DVI data line (A) 3 TMDS Data2/4 shield shield 4 NC* 5 NC 6 DDC clock (SCL) display data channel clock (I/O) 7 DDC data (SDA) display data channel data (I/O) 8 analogue vertical sync (VSYNC) analogue vertical sync signal (A) 9 TMDS Data1- DVI data line (A) 10 TMDS Data1+ DVI data line (A) 11 TMDS Data1/3 shield shield 12 NC 13 NC 14 +5V power (VCC) +5V power for DCC (A) 15 Ground (return for V, Hsync and Vsync) analogue ground (GND) 16 Hot plug detect 17 TMDS Data 0- DVI data line (A) 18 TMDS Data 0+ DVI data line (A) 19 TMDS Data0/5 shield shield 20 NC 21 NC 22 TMDS clock shield shield 23 TMDS clock+ DVI clock line (A) 24 TMDS clock- DVI clock line (A) C1 Analogue red (R) analogue red signal (A) C2 Analogue green (G) analogue green signal (A) C3 Analogue blue (B) analogue blue signal (A) C4 Analogue horizontal sync (HSYNC) analogue horizontal sync signal (A) C5 Analogue ground (analogue R, G, & return) analogue ground (GND) To allow the PC BIOS and operating system to properly detect and operate the DVI or CRT monitor, we recommend that you attach the monitor prior to starting the PC (automatic terminal detect). E 674 GB 19 07.03.2007
- Page 1 and 2: Kuhnke Electronics Instruction Manu
- Page 3 and 4: KUHNKE Automation Table of Contents
- Page 5 and 6: KUHNKE Automation Table of Contents
- Page 7 and 8: 1 Introduction Performance in a nut
- Page 9 and 10: KUHNKE Automation Reliability, Safe
- Page 11 and 12: KUHNKE Automation Reliability, Safe
- Page 13 and 14: KUHNKE Automation Hardware 3 Ventur
- Page 15 and 16: KUHNKE Automation Hardware 3.4 Tech
- Page 17: KUHNKE Automation Hardware 3.6 Phys
- Page 21 and 22: KUHNKE Automation Hardware 3.7.7 Et
- Page 23 and 24: KUHNKE Automation Hardware 3.9 Stor
- Page 25 and 26: KUHNKE Automation Hardware 3.11 Ext
- Page 27 and 28: KUHNKE Automation Hardware 3.12.4 F
- Page 29 and 30: KUHNKE Automation Hardware 3.13 Ven
- Page 31 and 32: KUHNKE Automation Hardware 4 Instal
- Page 33 and 34: KUHNKE Automation Software 5 Start-
- Page 35 and 36: KUHNKE Automation Software Windows
- Page 37 and 38: KUHNKE Automation Software 6.1 Comp
- Page 39 and 40: KUHNKE Automation Software 6.2.3 OP
- Page 41 and 42: KUHNKE Automation Software 6.3.3 Ul
- Page 43 and 44: KUHNKE Automation Software 6.5 Vent
- Page 45 and 46: KUHNKE Automation Software 7.1.2 Co
- Page 47 and 48: KUHNKE Automation Software 7.1.5 OP
- Page 49 and 50: KUHNKE Automation Software • Deve
- Page 51 and 52: KUHNKE Automation Software This com
- Page 53 and 54: KUHNKE Automation Software Sometime
- Page 55 and 56: KUHNKE Automation Software 7.5 Conn
- Page 57 and 58: KUHNKE Automation Software 7.5.2 Et
- Page 59 and 60: KUHNKE Automation Software • Star
- Page 61 and 62: KUHNKE Automation Software 9 Mainte
- Page 63 and 64: KUHNKE Automation Appendix 10 Appen
- Page 65 and 66: KUHNKE Automation Appendix E 674 GB
- Page 67 and 68: KUHNKE Automation Appendix Max. pow
Hardware KUHNKE Automation<br />
3.7 <strong>Ventura</strong> <strong>IPC</strong> Power Supply and Ports<br />
3.7.1 24 VDC Power Supply<br />
3.7.2 Operative Earth<br />
3.7.3 Serial Ports "COM1 and COM2"<br />
1<br />
6<br />
2<br />
7<br />
3<br />
8<br />
4<br />
9<br />
5<br />
Only attach the unit to a 24 VDC power supply source if the source is guaranteed<br />
to meet safe extra low voltage requirements (SELV).<br />
Please use the connector from the package to attach the unit to the power<br />
supply.<br />
The admissible diameter of the cord connecting the 24 VDC power is between<br />
0.75 mm 2 and 2.5 mm 2 .<br />
Connector 2-pin, male, 2.5 mm 2<br />
Pin Function<br />
L+ Supply voltage +24 VDC<br />
L GND<br />
Connect operative earth to the protective earth conductor of the switching<br />
cabinet or the system that the PC is installed in. Use the flat plug (6.3 mm x<br />
0.8 mm) on the bottom side of the unit.<br />
The minimum cross section must be no less than 2.5 mm 2 . Try to keep the<br />
lead to the cabinet terminal as short as possible.<br />
A low-impedance earth conductor improves the dissipation of interference<br />
received via external power supply cables, signal cables or cables of peripheral<br />
units.<br />
<strong>Ventura</strong> <strong>IPC</strong> has two serial COM ports for communication with peripherals<br />
such as terminals, modems, etc. A 9-pin D-Sub connector is used to attach<br />
peripherals with a suitable cable.<br />
Connector 9-pin D-SUB, male<br />
Pin Function<br />
1 -<br />
2 TxD<br />
3 RxD<br />
4 -<br />
5 GND<br />
6 -<br />
7 CTS<br />
8 RTS<br />
9 -<br />
18 E 674 GB<br />
07.03.2007