Shoe Design and Visualization

More documents

Recommendations

Info

To define the transition area SHOE DESIGN AND VISUALIZATION WITH RHINOCEROS 1 Draw a Line that defines the center of the transition area that will be removed. (Curve menu: Line > Single Line) Use an average inclination between the line perpendicular to the vamp curve and the line perpendicular to the sole curve. 2 Offset this line 20 mm on either side of this line as shown. (Curve menu: Offset Curve) To define the rotation point Draw a reference line from the intersection of the inside sole edge and the central transition line. 1 Use the DupEdge command to create a curve from the edge of the sole surface. (Curve menu: Curve From Objects > Duplicate Edge) 2 In the Right viewport, use the Line command with the Int object snap to start the reference line at the apparent intersection of the edge curve and the central transition line. (Curve menu: Line > Single Line) Draw the line anywhere in space. You are only interested in the intersection point. Copyright © 2005, Institute of Biomechanics of Valencia and Robert McNeel & Associates. 41
Rotating the backpart SHOE DESIGN AND VISUALIZATION WITH RHINOCEROS To raise the heel area, you will rotate the backpart of the last around the intersection of the central line and the interior sole curve. To split the shoe surfaces 1 Explode the last polysurface. (Edit menu: Explode) 2 In the Right viewport, Split the shoe surfaces at the central transition line. (Edit menu: Split) To rotate the backpart 1 Select all the rear last surfaces (topline surface, upper, and sole). 2 In the Right viewport, use the Rotate command to rotate the parts. (Transform menu: Rotate) The base point of the rotation is the intersection of the central transition curve and the interior sole curve. Snap to the endpoints of the two horizontal lines that represent the current heel height and the new 20 mm height to establish the rotation angle. Copyright © 2005, Institute of Biomechanics of Valencia and Robert McNeel & Associates. 42
Page 1 and 2: Rhinoceros Advanced Training Series
Page 3 and 4: Table of Contents SHOE DESIGN AND V
Page 5 and 6: SHOE DESIGN AND VISUALIZATION WITH
Page 7 and 8: Rendering for Presentation SHOE DES
Page 13 and 14: 2 Creating a Last Model SHOE DESIGN
Page 19 and 20: Refining the sole curves SHOE DESIG
Page 37 and 38: To close the last SHOE DESIGN AND V
Page 41 and 42: Creating the upper surface SHOE DES
Page 43 and 44: Creating the sole surface SHOE DESI
Page 45: To set up the model 1 Open the file
Page 53 and 54: To join the last SHOE DESIGN AND VI
Page 57 and 58: Trimming the surfaces SHOE DESIGN A
Page 59 and 60: To edit the curve control points SH
Page 61 and 62: To join the last SHOE DESIGN AND VI
Page 63 and 64: To create the reference curves SHOE
Page 65 and 66: To create the reference curves SHOE
Page 69 and 70: S H O E D E S I G N A N D V I S U A
Page 75 and 76: Creating a Boot Sole S H O E D E S
Page 79 and 80: To create defining curves 1 Hide th
Page 97 and 98:
S H O E D E S I G N A N D V I S U A
Page 99 and 100:
Page 101 and 102:
Creating the basic sole volume S H
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Creating the slipsole S H O E D E S
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
3 Select the side surface and sole.
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
To create the insole edge surface S
Page 131 and 132:
Page 133 and 134:
To finish the insole S H O E D E S
Page 135 and 136:
5 Modeling the Finish Details S H O
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
To remodel the edge surface S H O E
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Creating the padded cuff S H O E D
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Gradient view. Simple rendering wit
Page 179 and 180:
Penguin render with background. S H
Page 181 and 182:
Set up the view S H O E D E S I G N
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Render the scene with the three lig
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Ground Plane S H O E D E S I G N A
show all

Shoe Design and Visualization

Create successful ePaper yourself

Delete template?

Save as template?