Shoe Design and Visualization

More documents

Recommendations

Info

SHOE DESIGN AND VISUALIZATION WITH RHINOCEROS 4 To create a curve through these points, use the CurveThroughPt command, with the Closed option set to No. (Curve menu: Free-form > Fit to Points) 5 Rebuild the curve with fewer control points (5 to 8 points can be enough). (Edit menu: Rebuild) 6 Use the PointsOn command to display the curve’s control points, and adjust the points in each of the viewports until you are satisfied with the curve shape. (Edit menu: Control Points > Show control points) You can use the CurvatureGraph command to refine the curvature. (Analyze menu: Curvature Graph On) It is a good idea to make the endpoints of the vamp curve lie exactly on the topline and sole profile cross-section curves. Copyright © 2005, Institute of Biomechanics of Valencia and Robert McNeel & Associates. 23
SHOE DESIGN AND VISUALIZATION WITH RHINOCEROS 7 Use the PointsOn command to display the control points on the vamp curve. (Edit menu: Control Points > Show control points) 8 Use the Move command with the Point and Near object snaps to move the control point at each end of the curve onto the crosssection curves. (Transform menu: Move) 9 Repeat these steps to generate the remaining radial curves. Copyright © 2005, Institute of Biomechanics of Valencia and Robert McNeel & Associates. 24
Page 1 and 2: Rhinoceros Advanced Training Series
Page 3 and 4: Table of Contents SHOE DESIGN AND V
Page 5 and 6: SHOE DESIGN AND VISUALIZATION WITH
Page 7 and 8: Rendering for Presentation SHOE DES
Page 13 and 14: 2 Creating a Last Model SHOE DESIGN
Page 19 and 20: Refining the sole curves SHOE DESIG
Page 27: SHOE DESIGN AND VISUALIZATION WITH
Page 37 and 38: To close the last SHOE DESIGN AND V
Page 41 and 42: Creating the upper surface SHOE DES
Page 43 and 44: Creating the sole surface SHOE DESI
Page 45 and 46: To set up the model 1 Open the file
Page 47 and 48: Rotating the backpart SHOE DESIGN A
Page 53 and 54: To join the last SHOE DESIGN AND VI
Page 57 and 58: Trimming the surfaces SHOE DESIGN A
Page 59 and 60: To edit the curve control points SH
Page 61 and 62: To join the last SHOE DESIGN AND VI
Page 63 and 64: To create the reference curves SHOE
Page 65 and 66: To create the reference curves SHOE
Page 69 and 70: S H O E D E S I G N A N D V I S U A
Page 75 and 76: Creating a Boot Sole S H O E D E S
Page 79 and 80:
To create defining curves 1 Hide th
Page 81 and 82:
S H O E D E S I G N A N D V I S U A
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Creating the basic sole volume S H
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Creating the slipsole S H O E D E S
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
3 Select the side surface and sole.
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
To create the insole edge surface S
Page 131 and 132:
Page 133 and 134:
To finish the insole S H O E D E S
Page 135 and 136:
5 Modeling the Finish Details S H O
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
To remodel the edge surface S H O E
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Creating the padded cuff S H O E D
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Gradient view. Simple rendering wit
Page 179 and 180:
Penguin render with background. S H
Page 181 and 182:
Set up the view S H O E D E S I G N
Page 183 and 184:
Page 185 and 186:
Page 187 and 188:
Render the scene with the three lig
Page 189 and 190:
Page 191 and 192:
Page 193 and 194:
Ground Plane S H O E D E S I G N A
show all

Shoe Design and Visualization

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?