Terminal block labelling - Kablo Etiketi

More documents

Recommendations

Info

Material properties Comparative properties of polycarbonate and polyamide label plates For your label plates Murrplastik Systemtechnik uses high-quality polycarbonate meeting the requirements laid down by UL94 for the top fire classification V0. This offers clear advantages over polyamide as used by our competitors. Polycarbonate (PC) is used in applications requiring a high-quality surface finish in respect of scratch resistance and gloss level. As such, PC is widespread in the automotive sector, where examples of its use include headlight lenses and PC/ABS blends in the interior. By contrast, polyamide (PA) is rarely found as a blend in interior fittings. Polyamides are, however, prevalent under the bonnet, for example, where less significance is attached to the appearance. For use as a label plate polyamide has another unfavourable property: ambient water absorption of approx. two weight percent. This can cause dimensional variations (small dimensions at low temperatures and low air humidity, large dimensions at high temperatures and high air humidity). While this may not affect the dimensions of the label plates too severely, it does unduly impact on the properties of the material. Indeed, if water absorption is low the material is very brittle and tends to break (e.g. when latching onto a terminal <strong>block</strong>). Conversely, if water absorption is high then it is very soft and it may be difficult to separate plates from each other (tear response). In terms of its inscription properties polycarbonate is streets ahead of polyamide. Since PC is more prone to chemical reaction it lends itself well to ink and also laser inscription. Whereas PA scarcely reacts to the energy application of laser light the colour change achieved with PC is outstanding. The chemical reactivity of polycarbonate during inscription makes it an excellent abrasion-resistant surface for inks. If the resistance to abrasion and water is good in both materials then the inscription on polyamide wears off significantly if comes into contact with oil, petrol or spirit. Polycarbonate, however, is also resistant to these substances. Material description Material Description Polycarbonate (PC): Excellent surface gloss and transparency (natural), high mechanical strength and dimensional stability under heat, outstanding electrical and dielectric properties, superb dimensional accuracy and low water absorption. Impact resistance up to approx. 150 °C and, as a general rule, PC is self-extinguishing without the addition of fire-retardants. Polyamide (PA): Broad range of properties covered by different types (PA 6 and PA6.6 are frequently used). Generally good electrical and mechanical properties with resistance to impact and abrasion being particularly strong. When dry, PA is sensitive to impact. Water absorption renders PA flexible. Polyvinyl chloride (PVC): Soft PVC is made from polyvinyl chloride, softeners and process materials, e.g. stabilisers and lubricants. PVC is resistant to corrosive saline solutions and most acids. Thermoplastic polyurethane (TPU) : Outstanding features of this material include its high flexibility even at low temperatures, high continuous operating temperature, high resistance to tear propagation and very good restoring forces, high resistance to grease, oil, solvents, high-energy radiation and ultraviolet light. 184 Murrplastik Systemtechnik GmbH Postfach 1143 D-71567 Oppenweiler A +49 (0 ) 71 91/4 82-0 E +49 (0 ) 71 91/4 82-2 80 www.murrplastik.de info@murrplastik.de
Material properties Tests and test procedures Test Test procedure Materials testing Flammability acc. to UL94 Hardness test as per Shore A - ISO 868 Ageing Regular testing in climate simulation chamber as per Murrplastik in- house standard Functional testing Trial mounting of sleeves at different temperatures. Assessment of fit at maximum and minimum diameters. Handling test on carrier/plate. Test on fit of plate in sleeve. Vibration, shock and impact testing Vibration, shock and impact test conforming to DIN EN 50155 Point 10.2.11 Simulated durability test using increased wide band random vibration as specified by DIN EN 61373 (VDE 0155 Part 103): 1999-11 Point 9.1 Category 1B Smear stability Tests measuring resistance to wiping off machine oil, water, ethyl alcohol and hand perspiration. Scratch resistance/abrasion Test determining changes to legibility with different types of inscription (ink / printing / laser) pursuant to Murrplastik in-house standard. Ultraviolet light resistance Test in ultraviolet light chamber in accordance with Murrplastik in- house standard. Assessment of <strong>labelling</strong> for clear legibility. Standard: DIN EN ISO 4892-2 Chemical resistance of inscription Test on chemical resistance according to Murrplastik in-house standard. Murrplastik Systemtechnik GmbH Postfach 1143 D-71567 Oppenweiler A +49 (0 ) 71 91/4 82-0 E +49 (0 ) 71 91/4 82-2 80 www.murrplastik.de info@murrplastik.de 185
Page 1 and 2:
LABELLING SYSTEMS 2005 / 2006 Murrp
Page 3 and 4:
Contents Introduction to the labell
Page 5 and 6:
aided labelling software and hardwa
Page 7 and 8:
End: What can be labelled Labelling
Page 9 and 10:
Photograph: Courtesy of ABB Flexibl
Page 11 and 12:
SINGLE WIRE, CABLE AND CONDUIT LABE
Page 13 and 14:
Multi-line Halogenfree HB / VO 76 K
Page 15 and 16:
10.0 2/0 11.0 BS 10 3/0 12.0 KTH/Q
Page 17 and 18:
Single wire, cable, and conduit lab
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
TERMINAL BLOCK LABELLING Murrplasti
Page 45 and 46:
Terminal block labelling Terminal b
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Terminal block labelling KET type (
Page 59 and 60:
Terminal block labelling KMR type (
Page 61 and 62:
Terminal block labelling KPX type (
Page 63 and 64:
Terminal block labelling KWI type (
Page 65 and 66:
Terminal block labelling TK type (A
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
COMPONENT AND COMPONENT LOCATION LA
Page 73 and 74:
Component and component location la
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
LABELLING OF PUSH-BUTTONS AND SIGNA
Page 113 and 114:
Labelling of push-buttons and signa
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
SYSTEM LABELLING Murrplastik System
Page 125 and 126:
System labelling DM label plate Tem
Page 127 and 128:
SOFTWARE Murrplastik Systemtechnik
Page 129 and 130:
Software ACS Professional software
Page 131 and 132:
Software ACS Professional software
Page 133 and 134: OVERVIEW OF OUTPUT SYSTEMS Murrplas
Page 135 and 136: MVPS-G3-XXL Fields of application T
Page 137 and 138: Output systems Printing system Labe
Page 139 and 140: PLOTTER SYSTEMS Murrplastik Systemt
Page 141 and 142: Plotter system MVPS-G3-T plotter sy
Page 143 and 144: Plotter system Porty P300 and acces
Page 145 and 146: PLOTTER SYSTEMS ACCESSORIES Murrpla
Page 147 and 148: Plotter system accessories Base pla
Page 149 and 150: Plotter system accessories Ink, cle
Page 151 and 152: THERMAL TRANSFER PRINTER AND ACCESS
Page 153 and 154: ENGRAVING SYSTEMS Murrplastik Syste
Page 155 and 156: Engraving systems CAM engraving mac
Page 157 and 158: ENGRAVING SYSTEMS ACCESSORIES Murrp
Page 159 and 160: Engraving systems accessories CAM e
Page 165 and 166: Engraving systems accessories DMG l
Page 167 and 168: ACCESSORIES Murrplastik Systemtechn
Page 169 and 170: Accessories ACS function tool Multi
Page 171 and 172: Accessories KB / KKB / KBM cable ti
Page 173 and 174: Accessories SH screwed holder -40 t
Page 175 and 176: Accessories Cable tie rail KBL -40
Page 177 and 178: LABELLING AND FITTING SERVICE DL Mu
Page 179 and 180: We inscribe label plates, sheet lab
Page 181 and 182: MATERIAL PROPERTIES Murrplastik Sys
Page 183: Tensile Tear Bonding Solubil- Prope
Page 187 and 188: Product range Cable entry and cable
Page 189 and 190: Worldwide Hong Kong Worldtex & Co.
Page 191 and 192: Notes Murrplastik Systemtechnik Gmb
Page 193 and 194: Notes Murrplastik Systemtechnik Gmb
Page 195 and 196: All information concerning the chem
Page 197 and 198: Temperature range Material Fire cla
show all

Terminal block labelling - Kablo Etiketi

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?