7900 Instrument Stand - Haag-Streit USA

More documents

Recommendations

Info

6 Warning: TO PreVenT Fire Or shOCk haZarD, DO nOT exPOse This aPPlianCe TO rain Or mOisTure. aTTenTiOn: POur PrÉVenir le risQue D’inCenDie Ou De ChOC, n’exPOseZ Pas CeT aPPareil À la Pluie Ou À l’humiDiTÉ. TeChniCal sPeCiFiCaTiOns rating for 120V instrument stand This equipment is rated Class I, Type B Equipment Model Instrument Stand 7900 Volts Hertz Amps 120V 50/60 12.0 Class I Type B � �� rating for 230V instrument stand This equipment is rated Class I, Type B Equipment Model Instrument Stand 7900 Volts Hertz Amps 230V 50/60 6.0 Class I Type B � �� U.S. Patent No. D503,233 D512,507 5,717,480 D504,515 D514,701 5,907,387 D506,257 D424,200 6,264,329 imPOrTanT user Warnings Warning- exPlOsiOn: This sTanD musT nOT be useD in The PresenCe OF Flammable anesTheTiCs. “aVerTissanT” - DÉCOmPOsiTiOn : CeTTe gabariT ne DOiT Pas êTre uTilisÉe en PrÉsenCe Des anesThÉsiQues inFlammables POTenTial eleCTrOmagneTiC or OTher inTerFerenCe This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving device. • Increase the separation between the equipment. • Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected. • Consult the manufacturer or field service technician for help. This product contains lead. Check with local ordinance or laws for proper disposal. IN-7900
2. insTallaTiOn 2.1. unpacking 2.1.1. base unit 2.1.1.1 Remove all external shipping tapes and wrappings. Remove the base unit from the skid and set it in the desired, final location. 2.1.1.2 Loosen the two screws that hold the back cover (Figure 1) in place, located in bottom of cover. Cover lifts off the base unit. 2.1.1.3. Squeeze, the slit lamp arm release lever (Figure 1) and at the same time push down on slit lamp arm. Arm should move approximately 1/4 inch. Release the lever to set the slit lamp arm lock. 2.1.1.4. Inside the rear of the unit, remove the wood brace beneath the counterbalance weights and the cords which hold incremental weights to the large weight. While pushing firmly down (50 pounds force) on the slit lamp arm, again squeeze the lock release lever. Allow the slit lamp arm to rise to its full height and again release the lever. Warning- WiTh WeighT braCe remOVeD, arm assemblY Will rise abruPTlY iF release leVer is DePresseD. aVerTissanT -lOrsQue le blOQueur De DÉPlaCemenT esT reTirÉ, le bras COnTrebalanCÉ remOnTera PrOmPTemenT si le leVier Du Frein esT enFOnCÉ. 2.2. instrument Console/base Cap CauTiOn- The power supply cord should not be connected to the power supply during the installation process. aVerTisseZ -le cordon d’alimentation ne doit pas être connecté au secteur électrique pendant d’installation. Refractor Suspension Arm Auxiliary (Third) Arm Instrument Console or Base Cap Handle Release Lever Slit Lamp Arm Handle Overhead Lamp Monitor Arm Figure 1 Support Column 31” (787.4 mm) 16” (406.4 mm) 7 1/2 ” (190.5 mm) nOTe: If you are installing room light controls on this instrument stand, also refer to the “Eclipse Room Light Control Operating Instructions Section.” nOTe : Si vous installez le système de contrôles d’éclairage sur le support ophtalmique, veuillez suivre les consignes d’installation en vous référant au manuel d’instruction du système de contrôle d’éclairage éclipse. 2.2.1. replacement or repair Back Cover Wood Brace (Inside) IN-7900 7 Base Unit In the event that the instrument console or cap must be mounted or removed for replacement or repair purposes, it will be necessary to remove the back cover and disconnect the eight connectors from the console. To continue removing the console, remove the three Phillips Head screws from the
Page 1 and 2: ��INSTALLATION AND OPERAT
Page 3 and 4: Table of Contents imPOrTanT inFOrma
Page 5: 1. inTrODuCTiOn 1.1. This Installat
Page 9 and 10: TABLE 1 SWITCH SETTINGS FOR B/P VOL
Page 11 and 12: Figure 4a Figure 4b Figure 4C Figur
Page 13 and 14: 3. OPeraTing insTruCTiOns 3.1. slit
Page 15 and 16: CauTiOn- The lamp inside the instru
Page 17 and 18: 3.6.2 • The round button under th
Page 19 and 20: 3.8.2 incandescent vs. Fluorescent
Page 21 and 22: Warning-The eCliPse inFrareD rOOm l
Page 23 and 24: oom switch (rOOm) • Dual Zone tur
Page 25 and 26: P/N 17185 0.22 Figure 18 single ZOn
Page 27 and 28: P/N 17187 Figure 20 FluOresCenT inT
Page 29 and 30: TrOubleshOOTing guiDe insTrumenT sT
Page 31 and 32: Cleaning Painted surfaces The paint
Page 33 and 34: (nOTes) IN-7900 33
Page 35 and 36: 19 14 21 Figure 22 mODel 7900 insTr
Page 37 and 38: item part no. description item part
Page 39 and 40: item part no. description 1 1627295
Page 57 and 58:
item part no. description item part
Page 59 and 60:
item part no. description item part
Page 61 and 62:
IN-7900 61
Page 63 and 64:
IN-7900 63
Page 65 and 66:
(NOtES) IN-7900 65
Page 67 and 68:
limited warranty the reliance® pro
show all

7900 Instrument Stand - Haag-Streit USA

Create successful ePaper yourself

Delete template?

Save as template?