7900 Instrument Stand - Haag-Streit USA

More documents

Recommendations

Info

22 SWitchpAck #2 (SW2) switch 1 through 3 These switches are used to determine the type and voltage of the Indirect Ophthalmoscope bulb. See the Chart below. B UL B VOL T AG E A ND T Y P E -IND. OP HT HA L MOS C OP E S witch 1 2 3 6.5V /18W, Incandescent OF F OF F OF F R S V D Incandescent ON OF F OF F R S V D Incandescent OF F ON OF F R S V D Incandescent ON ON OF F 6V /10W Halogen OF F OF F ON 6V /20W Halogen ON OF F ON 12V /12W Halogen OF F ON ON R S V D Halogen ON ON ON switch 4 • Turn Switch 4 ON if your system contains a indirect hanger (Figure 13) for an Indirect Ophthalmoscope and you want that hanger to automatically supply power to the instrument. note: Turn Switch 5 on SW1 OFF if turning Switch 4 ON. note: Positionnez le contact 5 á la position arrêt sur l’interrupteur SW1 et positionnez le contact 4 EN position MARCHE. • Turn Switch 4 OFF if your system does not contain a hanger for an Indirect Ophthalmoscope. In this case, power is turned ON and OFF to the instrument via the B/P Switch on the front panel (See Switch 5 on SW1). switch 5 • If you want your system to beep whenever a switch is pressed , set Switch 5 ON. • If you do not want to hear a beep whenever a switch is pressed, set Switch OFF. switch 6 • Reserved switches 7 and 8 These switches are used to determine the type and voltage of the Slit Lamp bulb. See chart to the above right.(DOES NOT APPLY TO INSTRUMENT STANDS) B UL B VOL T AG E A ND T Y P E -S L IT L A MP B UL B S witch 7 8 6V /4.5A, Incandescent OF F OF F R S V D ON OF F 6V /20W Halogen OF F ON 12V /30W Halogen ON ON standby switch (sTbY) • OFF- Unit is deactivated, except for charging wells. • ON- Activates all unit functions Figure 14 (F actory default) auxiliary switch (aux1) • Affects the room lights and is programmable. • See section 3.8.3 for programming instructions if you have a single-zone infrared receiver. • See Switch 7 of Switchpack #1 in the Programming Instructions section of this manual for details. IN-<strong>7900</strong>
oom switch (rOOm) • Dual Zone turns the ROOM Lights OFF or ON to a pre-programmed intensity. • Single Zone turn ROOM Lights OFF or full ON. room Down switch • Decreases the intensity of the ALL room light(s). room up switch • Increases the intensity of the ALL room lights(s). lamp switch (lamP) • Affects the room lights and is programmable. • See section 3.8.3 for programming instructions if you have a single-zone infrared receiver. • See Switch 8 on Switchpack #1 in the Programming Instructions Section of this manual for details binding Post switch (b/P) • Affects the room lights and is programmable. • See section 3.8.3 for programming instructions if you have a single-zone infrared receiver. • See Switch 5 on Switchpack #1 in the Programming Instructions Section of this manual for details. hanger switch • Affects the room lights and is programmable. • See Switch 4 on Switchpack #2 in the Programming Instructions Section of this manual for details. Hanger Binding Posts toggle sWitCH rHeostat Figure 15 inDireCT hanger sWiTCh • See section 3.8.3 for programming instructions if you have a single-zone infrared receiver. slit lamp switch • Affects the room lights and is programmable. • See section 3.8.3 for programming instructions if you have a single-zone infrared receiver. • See Switch 6 on Switchpack #1 in the Programming Instructions Section of this manual for details. • Push button at the beginning of Slit Lamp examination, then push button again after examination is complete. Well #1 • Controls room light(s) when the rechargeable instrument is removed from well. • When the instrument is returned to the well, the room lights return to Scene #1. See section 3.8.3 for Programming Instructions. • See Switch 2 on Switchpack #1. Well #2 • Controls room light(s) when the rechargeable instrument is removed from the well. • When the instrument is returned to the well, the room lights return to Scene #1. See section 3.8.3 for Programming Instructions. • See Switch 3 on Switchpack #1. Well #3 • Controls room light(s) when the rechargeable instrument is removed from the well. • When the instrument is returned to the well, the room lights return to Scene #1. See section 3.8.3 for Programming Instructions. • See Switch 4 on Switchpack #1. 3.8.3 Programming single Zone room lights 3.8.3.1. Point the remote control (See Figure 14) at the single zone receiver. (See Figure 16) 3.8.3.2. Toggle the Room Lights Settings switch up or down to set the room lights at the desired intensity. 3.8.3.3. Press the switch designated for a section of the instrument stand. 3.8.3.4. Maintain pressure on the switch until the small LED located next to the receiver begins to blink. Example: If one sets the room light for use while using Well #1. Follow steps 1 and 2. Press the second switch from the top of the remote (Figure 14) until the LED next to it blinks. Now when Well #1 is removed, the room lights will dim down to the designated level. IN-<strong>7900</strong> 23
Page 1 and 2: ��INSTALLATION AND OPERAT
Page 3 and 4: Table of Contents imPOrTanT inFOrma
Page 5 and 6: 1. inTrODuCTiOn 1.1. This Installat
Page 7 and 8: 2. insTallaTiOn 2.1. unpacking 2.1.
Page 9 and 10: TABLE 1 SWITCH SETTINGS FOR B/P VOL
Page 11 and 12: Figure 4a Figure 4b Figure 4C Figur
Page 13 and 14: 3. OPeraTing insTruCTiOns 3.1. slit
Page 15 and 16: CauTiOn- The lamp inside the instru
Page 17 and 18: 3.6.2 • The round button under th
Page 19 and 20: 3.8.2 incandescent vs. Fluorescent
Page 21: Warning-The eCliPse inFrareD rOOm l
Page 25 and 26: P/N 17185 0.22 Figure 18 single ZOn
Page 27 and 28: P/N 17187 Figure 20 FluOresCenT inT
Page 29 and 30: TrOubleshOOTing guiDe insTrumenT sT
Page 31 and 32: Cleaning Painted surfaces The paint
Page 33 and 34: (nOTes) IN-7900 33
Page 35 and 36: 19 14 21 Figure 22 mODel 7900 insTr
Page 37 and 38: item part no. description item part
Page 39 and 40: item part no. description 1 1627295
Page 61 and 62: IN-7900 61
Page 63 and 64: IN-7900 63
Page 65 and 66: (NOtES) IN-7900 65
Page 67 and 68: limited warranty the reliance® pro

7900 Instrument Stand - Haag-Streit USA

Create successful ePaper yourself

Delete template?

Save as template?