7900 Instrument Stand - Haag-Streit USA
7900 Instrument Stand - Haag-Streit USA
7900 Instrument Stand - Haag-Streit USA
- TAGS
- haag-streit-usa.com
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Warning-The eCliPse inFrareD rOOm<br />
lighTs COnTrOl sYsTem musT maTCh<br />
The reQuiremenTs OF The user. iF The<br />
sYsTem is nOT PrOPerlY COnFigureD<br />
beFOre seCOnDarY POWer TO The uniT is<br />
TurneD On Via The sTbY sWiTCh, Damage<br />
TO The sYsTem Or insTrumenT bulbs<br />
maY OCCur.<br />
aVerTissanT-le sYsTÈme De COnTrôle<br />
inFrarOuge D’ÉClairage ÉCliPse DOiT<br />
COrresPOnDre aux COnDiTiOns De<br />
l’uTilisaTeur. si le sYsTÈme n’esT<br />
Pas COrreCTemenT COnFigurÉ aVanT<br />
D’allumer le suPPOrT OPhTalmiQue, Par<br />
le COnTrôle “sTbY”, Des DOmmages au<br />
suPPOrT Ou aux amPOules ÉleCTriQues<br />
PeuVenT se PrODuire.<br />
ECLIPSE ROOM LIGHT SYSTEM<br />
Press Here<br />
to turn oFF<br />
indireCt<br />
BulB ratings<br />
slit lamP<br />
BulB ratings<br />
sW2-1<br />
sW2-2<br />
sW2-3<br />
Hanger<br />
BeeP on<br />
oPen<br />
sW2-7<br />
sW2-8<br />
Press Here<br />
to turn on<br />
oFF<br />
sW2<br />
REAR VIEW OF CONSOLE ASSEMBLY<br />
eCliPse inFrareD rOOm lighT COnTrOls<br />
PrOgramming guiDe<br />
Configuring the system is accomplished by setting dip<br />
switches found on the circuit board. The dip switches<br />
are labeled SW1 and SW2. The following paragraphs<br />
provide the necessary information required to configure<br />
the system.<br />
sWiTChPaCk #1 (sW1)<br />
switch 1<br />
• Turn Switch 1 OFF if your system contains a single-zone<br />
infrared receiver.<br />
• Turn Switch 1 ON if your system contains a dual-zone<br />
infrared receiver (Factory default setting).<br />
1 2 3 4 5 6 7 8<br />
oFF<br />
sW1<br />
1 2 3 4 5 6 7 8<br />
enaBle-on<br />
dual Zone<br />
Well #1<br />
Well #2<br />
Well #3<br />
Binding Post<br />
s/l arm<br />
auXiliary<br />
lamP<br />
switch 2<br />
• Turn Switch 2 ON to enable Well #1 to affect room lights<br />
and fixation lights.<br />
• Turn Switch 2 OFF to disable Well #1 from affecting room<br />
lights and fixation lights.<br />
switch 3<br />
• Turn Switch 3 ON to enable Well #2 to affect room lights<br />
and fixation lights.<br />
• Turn Switch 3 OFF to disable Well #2 from affecting room<br />
lights and fixation lights.<br />
switch 4<br />
• Turn Switch 4 ON to enable Well #3 to affect room lights<br />
and fixation lights.<br />
• Turn Switch 4 OFF to disable Well #3 from affecting room<br />
lights and fixation lights.<br />
switch 5<br />
• If power to the Indirect Ophthalmoscope is controlled by<br />
the B/P Switch on the front panel, turn Switch 5 ON if<br />
you want the B/P Switch to affect room lights.<br />
• Turn Switch 5 OFF if you do not want the B/P Switch to<br />
affect room lights.<br />
switch 6<br />
• Turn Switch 6 ON to enable Slit Lamp Arm Switch to affect<br />
room lights.<br />
• Turn Switch 6 OFF to disable Slit Lamp Arm Switch from<br />
affecting room lights.<br />
switch 7<br />
• Turn Switch 7 ON to enable the AUX1 Switch to affect<br />
room lights.<br />
• Turn Switch 7 OFF to disable the AUX1 Switch from<br />
affecting room lights.<br />
switch 8<br />
• Turn Switch 8 ON to enable the LAMP Switch to affect<br />
room lights.<br />
• Turn Switch 8 OFF to disable the LAMP Switch from<br />
affecting room lights.<br />
IN-<strong>7900</strong> 21
Change language