7900 Instrument Stand - Haag-Streit USA

More documents

Recommendations

Info

16 Warning- main POWer (120VaC Or 240VaC) is alWaYs PresenT insiDe The sYsTem When The POWer COrD is PluggeD inTO The Wall. aVerTissanT- l’alimenTaTiOn ÉleC- TriQue De (120VaC Ou 240VaC) esT TOu- JOurs PrÉsenTe À l’inTÉrieur Du suP- POrT OPhTalmiQue QuanD Celui-Ci esT branChÉ sur le rÉseau ÉleCTriQue. 3.6.1.2. auxiliary switch (aux) • Turns MAIN power ON and OFF to the AUX power connector. • Turns the AUX LED ON when MAIN power is applied to the AUX power connector. • The primary purpose of the switch is to turn the projector ON and OFF. 3.6.1.3. lamp switch (lamp) • Turns the overhead lamp ON and OFF. • Turns the lamp ON at 50% intensity when the switch is pressed for the first time after the system’s power cord is plugged into the wall. Afterwards, the light will turn ON at its previous intensity level. • Turns the LAMP LED ON when power is applied to the overhead lamp. 3.6.1.4. lamp Down switch • Decreases the intensity of the overhead lamp. 3.6.1.5. lamp up switch • Increases the intensity of the overhead lamp. 3.6.1.6 binding Post switch (b/P) • The B/P Switch is enabled when Switch 5 of SW2 is turned OFF. See Table 1. • When enabled, turns power to the binding posts (Indirect Ophthalmoscope) ON and OFF. • Turns the B/P LED ON when power is applied to the Ophthalmoscope. • When disabled, the B/P Switch has no function. Power to the Ophthalmoscope is controlled by the optional hanger assembly. 3.6.1.7. b/P Down switch • Decreases the intensity of the Indirect Ophthalmoscope. 3.6.1.8. b/P up switch • Increases the intensity of the Indirect Ophthalmoscope 3.6.1.9. Chair base up switch • Causes the chair base to raise. 3.6.1.10. Chair base Down switch • Causes the chair base to lower 3.6.1.12. auto switch • On a low voltage 980, 7000, 710 or FX920 Chair, this switch causes the chair base to lower to its lowest position and the chair top to move to its full upright position. CauTiOn- The chair will move automatically. To sTOP chair movement, press the sTOP switch located on the side of the chair back. aVerTisseZ- la chaise ophtalmique se positionnera automatiquement. Pour arrêTer le mouvement de la chaise, appuyez sur le bouton “arrêT” situé du côté de la chaise. • On a low voltage 5200, 6200 or FXM920 Chair, this switch causes the chair base to lower to its lowest position. The chair top must be manually returned to it’s full upright position. CauTiOn- The chair will move automatically. To sTOP chair movement, press the sTOP switch located on the side of the chair back. aVerTisseZ- la chaise ophtalmique se positionnera automatiquement. Pour arrêTer le mouvement de la chaise, appuyez sur le bouton “arrêT” situé du côté de la chaise. • On an older high voltage chair, this switch causes the chair base to lower to its lowest position. The chair top does not move. CauTiOn- The chair will move automatically. To sTOP chair movement, press either the base uP or base DOWn switches located on the floor unit. aVerTisseZ- la chaise ophtalmique se positionnera automatiquement. Pour arrêTer le mouvement de la chaise, appuyez sur le bouton “hauT” ou “bas” situé sur le pédalier de la chaise. IN-<strong>7900</strong>
3.6.2 • The round button under the “B/P” arrows is used to turn on and off the indirect hanger. The up and down arrows are used to control the output voltage (i.e. the intensity) of the indirect bulb. 3.6.3 • The round button under the “LAMP” arrows is used to turn on and off the overhead lamp. The up and down arrows are used to control the output voltage (i.e. the intensity) of the overhead lamp. 3.7. Fuses �� Warning- DisCOnneCT FlOOr uniT FrOm main inPuT POWer beFOre PrOCeeDing WiTh eleCTriCal insPeCTiOns Or mainTenanCe. aVerTissemenT-DÉbranCheZ le suPPOrT OPhTalmiQue Du rÉseau ÉleCTriQue POur PrOCÉDer À une insPeCTiOns Ou mainTenanCe. CauTiOn- replace fuse(s) as marked. all fuses must be replaced with a fuse of the same size and rating. refer to the wiring diagrams on pages 56-59. l’aTTenTiOn- remplacement des fusible (s) tel qu’indiqué. Tous les fusibles doivent être remplacés avec un fusible de même taille et de même ampérage et/ou voltage. référez-vous aux diagrammes de câblage aux page 56-59. 3.7.1. Floor units contain two fuses located inside the AC Input Module on the Outlet Plate Assembly. 3.7.2. Consoles and Base Caps contain no additional fuses. 3.7.3. Fuse replacement (aC input module) method for removing fuse drawer: 1. The fuse drawer is located above the power cord. Remove the power cord. Place a small bladed screwdriver into appropriate slot (shown above) and push the flat spring towards the center of the power module until a click is heard. (Click may not be heard in all cases.) The drawer will come forward slightly. Once the flap has been pushed towards the center, the drawer will extend slightly beyond the power module. Remove the drawer by pulling it out by your fingers. CauTiOn- never install the drawer into the aC input module without fuses. aTTenTiOn- ne jamais introduire le module de support des fusibles sans avoir inséré les fusibles. IN-<strong>7900</strong> 17 2. 3. 4. 5.
Page 1 and 2: ��INSTALLATION AND OPERAT
Page 3 and 4: Table of Contents imPOrTanT inFOrma
Page 5 and 6: 1. inTrODuCTiOn 1.1. This Installat
Page 7 and 8: 2. insTallaTiOn 2.1. unpacking 2.1.
Page 9 and 10: TABLE 1 SWITCH SETTINGS FOR B/P VOL
Page 11 and 12: Figure 4a Figure 4b Figure 4C Figur
Page 13 and 14: 3. OPeraTing insTruCTiOns 3.1. slit
Page 15: CauTiOn- The lamp inside the instru
Page 19 and 20: 3.8.2 incandescent vs. Fluorescent
Page 21 and 22: Warning-The eCliPse inFrareD rOOm l
Page 23 and 24: oom switch (rOOm) • Dual Zone tur
Page 25 and 26: P/N 17185 0.22 Figure 18 single ZOn
Page 27 and 28: P/N 17187 Figure 20 FluOresCenT inT
Page 29 and 30: TrOubleshOOTing guiDe insTrumenT sT
Page 31 and 32: Cleaning Painted surfaces The paint
Page 33 and 34: (nOTes) IN-7900 33
Page 35 and 36: 19 14 21 Figure 22 mODel 7900 insTr
Page 37 and 38: item part no. description item part
Page 39 and 40: item part no. description 1 1627295
Page 61 and 62: IN-7900 61
Page 63 and 64: IN-7900 63
Page 65 and 66: (NOtES) IN-7900 65
Page 67 and 68:
limited warranty the reliance® pro
show all

7900 Instrument Stand - Haag-Streit USA

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?