7900 Instrument Stand - Haag-Streit USA
7900 Instrument Stand - Haag-Streit USA
7900 Instrument Stand - Haag-Streit USA
- TAGS
- haag-streit-usa.com
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
12<br />
2.10. Final assembly<br />
2.10.1. Console<br />
If an additional instrument is to be connected to the binding<br />
posts or if any auxiliary equipment is to be plugged into<br />
the”AUX” power connector, make these connections at<br />
this time.<br />
2.11. Chair assembly<br />
2.11.1 The chair control switches located on the floor unit<br />
may control any Reliance® low voltage chair. Refer to the<br />
chair instructions for unpacking and assembling the chair.<br />
2.11.2. A chair control cable is provided to control the<br />
vertical movement of the chair base from the floor unit.<br />
One end of the cable is to be inserted into the black circular<br />
receptacle on the Outlet Plate Assembly. See Figure 5. The<br />
other end of the cable is to be inserted into the mating<br />
receptacle marked “CHAIR CONTROL CABLE” in the rear of<br />
your Reliance® chair.<br />
2.12. miscellaneous<br />
Figure 5<br />
2.12.1. When attaching an instrument to the slit lamp arm,<br />
note the thrust bearing which should be in place between<br />
the instrument and the arm.<br />
2.12.2. Proper balance of an instrument on the slit lamp<br />
arm is achieved by adding or removing counter-balance<br />
weights as shown in Figure 6. See Page 12 for a table of<br />
weight settings.<br />
2.12.3 Finally, plug the power cord into a wall receptacle<br />
and check all electrical functions as described in the<br />
Installation and Operating Instructions. If all functions are<br />
normal, reattach the base unit rear cover.<br />
2.12.4 To disconnect power to <strong>Instrument</strong> <strong>Stand</strong> unplug<br />
power cord from wall receptacle.<br />
nOTe: Outlet wires are hot.<br />
nOTe : Les fils de sortie sont chauds<br />
CauTiOn-“accessory equipment connected<br />
to the analog and interfaces must be certified<br />
according to the respective ieC standards<br />
(i.e. ieC 950 for data processing equipment<br />
and ieC 601-1 for medical equipment).<br />
Furthermore all configurations shall comply<br />
with the system standard ieC 601-1-1.<br />
everybody who connects additional equipment<br />
to the signal input part or output part<br />
configures a medical system, and is therefore<br />
responsible that the system complies with<br />
the requirements of ieC 601-1-1. if in doubt,<br />
consult the technical services department or<br />
your local representative.”<br />
equipment with siP/sOP connectors should<br />
either indicate the connected equipment<br />
comply with ieC 601-1 and/or ieC 601-<br />
1-1 harmonized national standard or the<br />
combination should be evaluated.<br />
aTTenTiOn- “les équipements branché sur<br />
le support ophtalmique doivent répondre aux<br />
normes ieC (i.e. ieC 950 pour le matériel<br />
informatique et le ieC 601-1 pour le matériel<br />
médical). en outre toutes les configurations<br />
devront étre conformes á la norme ieC<br />
601-1-1.<br />
Tout personne qui branché un équipement<br />
supplémentaire au systéme doit s’assurer<br />
que cet équipement répond aux normes<br />
médicales ieC 601-1-1 et en est responsable.<br />
en cas de doute, consultez le service<br />
technique de votre distributeur ou votre<br />
préposé technique local.”<br />
le matériel avec des connecteurs de type<br />
siP/sOP devront être conformes à la norme<br />
ieC 601-1 et/ou être conformes à la norme<br />
nationale harmonisée ieC 601-1-1.<br />
IN-<strong>7900</strong>