Technical Design Report Super Fragment Separator

More documents

Recommendations

Info

DRAFT Figure 2.4.48: 3D view of the superferric quadrupole magnet with main coils and a yoke diameter of 1.4 m. Figure 2.4.49: Geometry of the end chamfer for the Super-FRS quadrupoles. The properties of the Super-FRS quadrupoles were calculated for a 3D model including special construction details. Such model for a quadrupole is shown in Figure 2.4.50. The calculations indicate that these additional construction elements do not influence the field distributions in the aperture noticeably. For all calculations the B-H curve as shown in Figure 2.4.51 was used. 57 40 65º 45º 48
DRAFT Figure 2.4.50: 3D model of the Super-FRS quadrupole magnet including holes and grooves. Indicated are also the end chamfers. Figure 2.4.51: BH-curve used in the 2D and 3D magnetic field calculations. 2.4.2.2.3 Superferric quadrupole magnets for the Energy Buncher 2D-Magnetic design The quadrupole magnets for the Magnetic Spectrometer and Energy Buncher at the exit of the Low-Energy Branch are superferric magnets having cold iron. The specifications of the quadrupoles are listed in Table 2.4.14 and its cross section is shown in Figure 2.4.52. 49
Page 1 and 2: DRAFT Technical Design Report Super
Page 3 and 4: Preface DRAFT The International Fac
Page 5 and 6: Contents DRAFT 2.4.1 System Design
Page 7 and 8: DRAFT Table 2.4.1: Parameters of th
Page 9 and 10: DRAFT degrader stage which provides
Page 11 and 12: Pre-Separator DRAFT In order to acc
Page 13 and 14: DRAFT coupling coefficients is give
Page 15 and 16: DRAFT Table 2.4.3: First-order matr
Page 17 and 18: DRAFT Main-Separator to the high-en
Page 19 and 20: DRAFT Table 2.4.5: Transmission T o
Page 21 and 22: DRAFT Figure 2.4.15: Resolution nec
Page 23 and 24: DRAFT Figure 2.4.17: Spectrometer m
Page 25 and 26: DRAFT Table 2.4.8: Design parameter
Page 27 and 28: DRAFT Figure 2.4.20: Side view of t
Page 29 and 30: DRAFT Figure 2.4.23: Coil cross-sec
Page 31 and 32: DRAFT Figure 2.4.25: Flux density d
Page 33 and 34: Figure 2.4.29: Assembly of two half
Page 35 and 36: DRAFT Figure 2.4.31: Cross section
Page 37 and 38: Figure 2.4.34: Sketch of the therma
Page 39 and 40: DRAFT To fulfill the required field
Page 41 and 42: DRAFT Figure 2.4.39: The 3D model o
Page 43 and 44: DRAFT Pole radius mm 100 210 250 25
Page 45 and 46: DRAFT Figure 2.4.43: Front, side, a
Page 47: ∆B/B 0.0 DRAFT Figure 2.4.46: Ave
Page 51 and 52: DRAFT Figure 2.4.54 and Table 2.4.1
Page 53 and 54: DRAFT 2.4.2.3.1 Radiation resistant
Page 55 and 56: DRAFT The water-cooled radiator con
Page 57 and 58: DRAFT Table 2.4.17: Coil parameters
Page 59 and 60: DRAFT Figure 2.4.63: Field distribu
Page 61 and 62: DRAFT Figure 2.4.65: Multiplet conf
Page 63 and 64: DRAFT Table 2.4.21 summarizes the r
Page 65 and 66: 2.4.2.6 Current Leads DRAFT The cur
Page 67 and 68: DRAFT Table 2.4.23 presents the lis
Page 69 and 70: 2.4.3 Power Converters DRAFT The po
Page 71 and 72: SCR structure DRAFT Regarding high
Page 73 and 74: a) Chopper circuit 3x400V b) Half b
Page 75 and 76: External Control System Data transf
Page 77 and 78: DRAFT Figure 2.4.77: Arrangement of
Page 79 and 80: SuperFRS Power Supply Effective App
Page 81 and 82: DRAFT The locations for the differe
Page 83 and 84: DRAFT Figure 2.4.80: Beam induced f
Page 85 and 86: DRAFT Figure 2.4.82: Two hybrids ca
Page 87 and 88: DRAFT Figure 2.4.84: Left panel: TP
Page 89 and 90: DRAFT extracted beams. Its use for
Page 91 and 92: Time of Flight measurement DRAFT At
Page 93 and 94: DRAFT together. Another option is t
Page 95 and 96: DRAFT Figure 2.4.88: Pillow seal po
Page 97 and 98: DRAFT Figure 2.4.90: Setup at the m
Page 99 and 100:
DRAFT An overview of the total vacu
Page 101 and 102:
2.4.7.4 Appendix - Technical Drawin
Page 103 and 104:
DRAFT Figure 2.4.96: Diagnostic cha
Page 105 and 106:
DRAFT Figure 2.4.98: Diagnostic cha
Page 107 and 108:
DRAFT Figure 2.4.100: Diagnostic ch
Page 109 and 110:
2.4.8 Particles Sources n/a 2.4.9 E
Page 111 and 112:
DRAFT movable, but BC3 must be able
Page 113 and 114:
DRAFT Figure 2.4.106: Spot size of
Page 115 and 116:
dE/dV [kJ/cm 3 ] 3 2 1 DRAFT includ
Page 117 and 118:
2.4.11.1.4 Design of the beam catch
Page 119 and 120:
DRAFT Figure 2.4.110: Calculated eq
Page 121 and 122:
DRAFT Figure 2.4.112: Location of b
Page 123 and 124:
DRAFT the carbon. Again mainly 7 Be
Page 125 and 126:
DRAFT maintenance of the carbon or
Page 127 and 128:
DRAFT material) and received the an
Page 129 and 130:
DRAFT commissioned in February 2005
Page 131 and 132:
DRAFT Table 2.4.28: Typical beam pa
Page 133 and 134:
DRAFT Figure 2.4.120: Surface tempe
Page 135 and 136:
DRAFT Figure 2.4.123: Schematic lay
Page 137 and 138:
DRAFT These results show that the i
Page 139 and 140:
DRAFT Like in the case of the rotat
Page 141 and 142:
DRAFT Figure 2.4.126: Left: Schemat
Page 143 and 144:
Page 145 and 146:
DRAFT Figure 2.4.129: Flow scheme o
Page 147 and 148:
DRAFT Since the weight of the cold
Page 149 and 150:
DRAFT With the cooling capacity spe
Page 151 and 152:
DRAFT Figure 2.4.134: Schematic of
Page 153 and 154:
S1 (a) Figure 2.4.136: (a) Zoom of
Page 155 and 156:
2.4.A Appendix DRAFT The appendix o
Page 157 and 158:
DRAFT experiment the EXL community
Page 159 and 160:
2.4.A1.3 Slow control and monitorin
Page 161 and 162:
DRAFT Figure 2.4.139: Architecture
Page 163 and 164:
DRAFT all FAIR accelerators will be
Page 165 and 166:
DRAFT source tier are split in two
Page 167 and 168:
DRAFT coupled from the ACS which is
Page 169 and 170:
DRAFT 2.4.A3.2 Work packages: descr
Page 171 and 172:
2.4.A3.2.4 Instrumentation Measurin
Page 173 and 174:
DRAFT this, planning a network layo
Page 175 and 176:
DRAFT 2.4.A3.3 Machine characterist
Page 177 and 178:
DRAFT installation of RALF was done
Page 179 and 180:
DRAFT The double ring synchrotrons,
Page 181 and 182:
DRAFT The first refrigerator, Cryo1
Page 183 and 184:
DRAFT shield 28874 + 25 g/s 22 bar
Page 185 and 186:
LHe storage Helium storage Helium s
Page 187 and 188:
Cryo2 Cryo3 CryoST DB 3 DRAFT Compr
Page 189 and 190:
DRAFT The cold connection will be m
Page 191 and 192:
DRAFT Measurements planned for each
Page 193 and 194:
DRAFT For magnets with less stringe
Page 195 and 196:
DRAFT The value, parameters, condit
Page 197 and 198:
DRAFT 3. Geometry tests For cryosta
Page 199 and 200:
DRAFT The Quench Heaters Tests has
Page 201 and 202:
DRAFT Figure 2.4.159: Photograph of
Page 203 and 204:
DRAFT The field properties listed i
Page 205 and 206:
DRAFT Figure 2.4.161: Schematic vie
Page 207 and 208:
DRAFT Figure 2.4.162: Scheme of the
Page 209 and 210:
2.4.A6.2.2 Shielding against direct
Page 211 and 212:
Page 213 and 214:
DRAFT Figure 2.4.165: An iron beam
Page 215 and 216:
DRAFT In a side view the flux of pr
Page 217 and 218:
DRAFT catcher 7 Be, 22 Na and 24 Na
Page 219 and 220:
DRAFT at the FRS (2·10 9 /spill as
Page 221 and 222:
DRAFT [1] H. Geissel et al., Nucl.
Page 223 and 224:
DRAFT [74] A. Fabich and J. Lettry,
show all

Technical Design Report Super Fragment Separator

Create successful ePaper yourself

Delete template?

Save as template?