Technical Design Report Super Fragment Separator

More documents

Recommendations

Info

DRAFT [105] M. Kauschke: Lastenentwicklung in der Kryoversorgung, November 2007. [106] B. Weckenmann: heat loads 0108, MS Excel sheet; January 2008 [107] K. Schippl: Cryogenic Bus Bar for SIS100 Magnets, November 2007 [108] P. Schnizer et al., "On the way to a measurement plan for GSI", Technical Note, Mar. 2004. [109] G. Moritz, et al., IEEE Trans. on Magnetics, 24 (1988) 942. [110] G. Moritz, Mechanical Equipment. In S. Turner, editor, CAS Magnetic Measurement and Alignment, pages 251–272. CERN, Aug. 1998. [111] A. Jain, "Magnetic field measurements and mapping techniques", Lecture in Academic Training program at CERN, http://agenda.cern.ch/fullAgenda.php?ida=a032529 [112] P. Schnizer et al., "Magnetic Field Analysis Magnetic field analysis for superferric accelerator magnets using elliptic multipoles and its advantages", accepted for publication in IEEE Trans. on Applied Superconductivity. [113] P. Schnizer et al., "Field Representation for Elliptic Apertures", Technical Report, GSI, Jan. 2008. [114] P. Schnizer et al., "A mole for measuring pulsed superconducting magnets", accepted for publication in IEEE Trans. on Applied Superconductivity. [115] A. Jain, "Field Quality Measurements at High Ramp Rates in a Prototype Dipole for the FAIR Project", Presented at 20th Biennial Conference on Magnet Technology, Philadephia, Aug. 2007. [116] J. DiMarco et al., "A Fast-Sampling, Fixed Coil Array for Measuring the AC Field of Fermilab Booster Corrector Magnets", Presented at 20th Biennial Conference on Magnet Technology, Philadelphia, Aug. 2007. [117] A. Stafiniak, "Superconducting Test Facility for FAIR project - status January 2008" , Internal Note 2008, GSI, MT-INT-AS-2008-001. [118] A. Stafiniak et al., "Commissioning of the Prototype Test Facility for Rapidly-Cycling Superconducting Magnets for FAIR" , MT20, 2007. [119] A. Ferrari and M. Pelliccioni, Rad. Prot. Dosimetry 76 (1998) 215. [120] S. Agosteo, G. Fehrenbacher and M. Silari, Nucl. Instr. and Meth. B226 (2004) 231. [121] K. Gunzert-Marx, "Nachweis leichter Fragmente aus Schwerionenreaktionen mit einem BaF2-Teleskop-Detektor", Ph.D Thesis, Technical University Darmstadt, Germany (2004). [122] J.-J. Gaimard and K.-H. Schmidt, Nucl. Phys. A531 (2003) 709. [123] E. Hanelt and K.-H. Schmidt, Nucl. Instr. and Meth. A321 (1992) 434. [124] International Commission on Radiological Protection, "Conversion Coefficients for use in Radiological Protection against External Radiation", ICRP Publication 74, Pergamon Press (1996). [125] J. Wei et al., "Beam-loss driven design optimization for the spallation neutron source (SNS) ring", in Proceedings of the 1999 Particle Accelerators Conference, New York, p.3185. [126] E. Mustafin, I. Hofmann and H. Weick, Nucl. Instr. and Meth. A501 (2003) 553. 224
Page 1 and 2:
DRAFT Technical Design Report Super
Page 3 and 4:
Preface DRAFT The International Fac
Page 5 and 6:
Contents DRAFT 2.4.1 System Design
Page 7 and 8:
DRAFT Table 2.4.1: Parameters of th
Page 9 and 10:
DRAFT degrader stage which provides
Page 11 and 12:
Pre-Separator DRAFT In order to acc
Page 13 and 14:
DRAFT coupling coefficients is give
Page 15 and 16:
DRAFT Table 2.4.3: First-order matr
Page 17 and 18:
DRAFT Main-Separator to the high-en
Page 19 and 20:
DRAFT Table 2.4.5: Transmission T o
Page 21 and 22:
DRAFT Figure 2.4.15: Resolution nec
Page 23 and 24:
DRAFT Figure 2.4.17: Spectrometer m
Page 25 and 26:
DRAFT Table 2.4.8: Design parameter
Page 27 and 28:
DRAFT Figure 2.4.20: Side view of t
Page 29 and 30:
DRAFT Figure 2.4.23: Coil cross-sec
Page 31 and 32:
DRAFT Figure 2.4.25: Flux density d
Page 33 and 34:
Figure 2.4.29: Assembly of two half
Page 35 and 36:
DRAFT Figure 2.4.31: Cross section
Page 37 and 38:
Figure 2.4.34: Sketch of the therma
Page 39 and 40:
DRAFT To fulfill the required field
Page 41 and 42:
DRAFT Figure 2.4.39: The 3D model o
Page 43 and 44:
DRAFT Pole radius mm 100 210 250 25
Page 45 and 46:
DRAFT Figure 2.4.43: Front, side, a
Page 47 and 48:
∆B/B 0.0 DRAFT Figure 2.4.46: Ave
Page 49 and 50:
DRAFT Figure 2.4.50: 3D model of th
Page 51 and 52:
DRAFT Figure 2.4.54 and Table 2.4.1
Page 53 and 54:
DRAFT 2.4.2.3.1 Radiation resistant
Page 55 and 56:
DRAFT The water-cooled radiator con
Page 57 and 58:
DRAFT Table 2.4.17: Coil parameters
Page 59 and 60:
DRAFT Figure 2.4.63: Field distribu
Page 61 and 62:
DRAFT Figure 2.4.65: Multiplet conf
Page 63 and 64:
DRAFT Table 2.4.21 summarizes the r
Page 65 and 66:
2.4.2.6 Current Leads DRAFT The cur
Page 67 and 68:
DRAFT Table 2.4.23 presents the lis
Page 69 and 70:
2.4.3 Power Converters DRAFT The po
Page 71 and 72:
SCR structure DRAFT Regarding high
Page 73 and 74:
a) Chopper circuit 3x400V b) Half b
Page 75 and 76:
External Control System Data transf
Page 77 and 78:
DRAFT Figure 2.4.77: Arrangement of
Page 79 and 80:
SuperFRS Power Supply Effective App
Page 81 and 82:
DRAFT The locations for the differe
Page 83 and 84:
DRAFT Figure 2.4.80: Beam induced f
Page 85 and 86:
DRAFT Figure 2.4.82: Two hybrids ca
Page 87 and 88:
DRAFT Figure 2.4.84: Left panel: TP
Page 89 and 90:
DRAFT extracted beams. Its use for
Page 91 and 92:
Time of Flight measurement DRAFT At
Page 93 and 94:
DRAFT together. Another option is t
Page 95 and 96:
DRAFT Figure 2.4.88: Pillow seal po
Page 97 and 98:
DRAFT Figure 2.4.90: Setup at the m
Page 99 and 100:
DRAFT An overview of the total vacu
Page 101 and 102:
2.4.7.4 Appendix - Technical Drawin
Page 103 and 104:
DRAFT Figure 2.4.96: Diagnostic cha
Page 105 and 106:
DRAFT Figure 2.4.98: Diagnostic cha
Page 107 and 108:
DRAFT Figure 2.4.100: Diagnostic ch
Page 109 and 110:
2.4.8 Particles Sources n/a 2.4.9 E
Page 111 and 112:
DRAFT movable, but BC3 must be able
Page 113 and 114:
DRAFT Figure 2.4.106: Spot size of
Page 115 and 116:
dE/dV [kJ/cm 3 ] 3 2 1 DRAFT includ
Page 117 and 118:
2.4.11.1.4 Design of the beam catch
Page 119 and 120:
DRAFT Figure 2.4.110: Calculated eq
Page 121 and 122:
DRAFT Figure 2.4.112: Location of b
Page 123 and 124:
DRAFT the carbon. Again mainly 7 Be
Page 125 and 126:
DRAFT maintenance of the carbon or
Page 127 and 128:
DRAFT material) and received the an
Page 129 and 130:
DRAFT commissioned in February 2005
Page 131 and 132:
DRAFT Table 2.4.28: Typical beam pa
Page 133 and 134:
DRAFT Figure 2.4.120: Surface tempe
Page 135 and 136:
DRAFT Figure 2.4.123: Schematic lay
Page 137 and 138:
DRAFT These results show that the i
Page 139 and 140:
DRAFT Like in the case of the rotat
Page 141 and 142:
DRAFT Figure 2.4.126: Left: Schemat
Page 143 and 144:
DRAFT Figure 2.4.128: Schematic lay
Page 145 and 146:
DRAFT Figure 2.4.129: Flow scheme o
Page 147 and 148:
DRAFT Since the weight of the cold
Page 149 and 150:
DRAFT With the cooling capacity spe
Page 151 and 152:
DRAFT Figure 2.4.134: Schematic of
Page 153 and 154:
S1 (a) Figure 2.4.136: (a) Zoom of
Page 155 and 156:
2.4.A Appendix DRAFT The appendix o
Page 157 and 158:
DRAFT experiment the EXL community
Page 159 and 160:
2.4.A1.3 Slow control and monitorin
Page 161 and 162:
DRAFT Figure 2.4.139: Architecture
Page 163 and 164:
DRAFT all FAIR accelerators will be
Page 165 and 166:
DRAFT source tier are split in two
Page 167 and 168:
DRAFT coupled from the ACS which is
Page 169 and 170:
DRAFT 2.4.A3.2 Work packages: descr
Page 171 and 172:
2.4.A3.2.4 Instrumentation Measurin
Page 173 and 174: DRAFT this, planning a network layo
Page 175 and 176: DRAFT 2.4.A3.3 Machine characterist
Page 177 and 178: DRAFT installation of RALF was done
Page 179 and 180: DRAFT The double ring synchrotrons,
Page 181 and 182: DRAFT The first refrigerator, Cryo1
Page 183 and 184: DRAFT shield 28874 + 25 g/s 22 bar
Page 185 and 186: LHe storage Helium storage Helium s
Page 187 and 188: Cryo2 Cryo3 CryoST DB 3 DRAFT Compr
Page 189 and 190: DRAFT The cold connection will be m
Page 191 and 192: DRAFT Measurements planned for each
Page 193 and 194: DRAFT For magnets with less stringe
Page 195 and 196: DRAFT The value, parameters, condit
Page 197 and 198: DRAFT 3. Geometry tests For cryosta
Page 199 and 200: DRAFT The Quench Heaters Tests has
Page 201 and 202: DRAFT Figure 2.4.159: Photograph of
Page 203 and 204: DRAFT The field properties listed i
Page 205 and 206: DRAFT Figure 2.4.161: Schematic vie
Page 207 and 208: DRAFT Figure 2.4.162: Scheme of the
Page 209 and 210: 2.4.A6.2.2 Shielding against direct
Page 211 and 212: DRAFT Figure 2.4.164: Schematic lay
Page 213 and 214: DRAFT Figure 2.4.165: An iron beam
Page 215 and 216: DRAFT In a side view the flux of pr
Page 217 and 218: DRAFT catcher 7 Be, 22 Na and 24 Na
Page 219 and 220: DRAFT at the FRS (2·10 9 /spill as
Page 221 and 222: DRAFT [1] H. Geissel et al., Nucl.
Page 223: DRAFT [74] A. Fabich and J. Lettry,
show all

Technical Design Report Super Fragment Separator

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?