PA-2312 Public Address 2 CH Power Amplifier - Ljudia
PA-2312 Public Address 2 CH Power Amplifier - Ljudia
PA-2312 Public Address 2 CH Power Amplifier - Ljudia
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Contents<br />
1. Unpacking and Installation.....................................................................................................1<br />
2. Features ................................................................................................................................2<br />
3. Front Panel Controls...............................................................................................................3<br />
4. Rear Panel Controls ...............................................................................................................4<br />
5. Applications ..........................................................................................................................6<br />
6. Block Diagram.......................................................................................................................7<br />
7. Specifications.........................................................................................................................8<br />
OFFICE :<br />
226-9 DUGJUNG - LI, HOE <strong>CH</strong>UN - EUB,<br />
YANGJU - KUN, KYUNGKI - DO, KOREA<br />
TEL : 82-351-860-7041~5, FAX : 82-351-858-1907<br />
Home Page : http://www.inter-m.co.kr<br />
E-mail : export@inter-m.co.kr
Unpacking and Installation<br />
Although it is neither complicated to install nor difficult to operate your <strong>PA</strong> <strong>Amplifier</strong>, a few minutes of your<br />
time is required to read this manual for a properly wired installation and becoming familiar with its many<br />
features and how to use them. Please take a great care in unpacking your set and do not discard the carton<br />
and other packing materials. They may be needed when moving your set and are required if it ever<br />
becomes necessary to return your set for service.<br />
Never place the unit near radiators, in front of heating vents, in excessively humid or dusty location to avoid<br />
early damage and for your years of quality use. Connect your complementary components as illustrated in<br />
the following page.<br />
CAUTION<br />
RISK OF ELECTRIC SHOCK<br />
DO NOT OPEN<br />
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.<br />
DO NOT REMOVE COVER (OR BACK).<br />
NO USER-SERVICEABLE <strong>PA</strong>RTS INSIDE.<br />
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.<br />
WARNING<br />
To prevent fire or shock hazard, do not<br />
expose the unit to rain or moisture.<br />
PUBLIC ADDRESS 2 <strong>CH</strong> POWER AMPLIFIER<br />
This symbol is intended to alert the user to the<br />
presence of uninsulated “dangerous voltage”<br />
within the product’s enclosure that may be of sufficient<br />
magnitude to constitute a risk of electric<br />
shock to persons.<br />
This symbol is intended to alert the user to the<br />
presence of important operation and maintenance<br />
(servicing) instructions in the literature<br />
accompanying the appliance.<br />
Caution: To prevent electric shock do not use this (polarized) plug<br />
with an extension cord, receptacle or other outlet unless<br />
the blades can be fully inserted to prevent blade exposure.<br />
Attentions: Pour prévenir les chocs électriques ne pas utiliser cette<br />
fiche polarisée avec un prolongateur, une prise de<br />
courant on une autre sortie de courant, sauf si les<br />
lames peuvent étre insérées à fond sans en laisser<br />
aucune partie à découvert.<br />
<strong>PA</strong>-<strong>2312</strong> 1
PUBLIC ADDRESS 2 <strong>CH</strong> POWER AMPLIFIER<br />
Features<br />
2<br />
- 2 <strong>CH</strong>ANNEL POWER AMPLIFIER<br />
This unit is composed of two power amplifier circuits.<br />
- GAIN VOLUME ADJUSTMENT & OUTPUT LEVEL INDICATOR IN FRONT <strong>PA</strong>NEL<br />
Gain volume is located at the front panel, so you can easily control output level. And you can monitor output<br />
level throughout LED indicator in front panel.<br />
- THERMAL PROTECTION & AUTOMATIC IDLING CiRCUITRY<br />
To insure stability and reliability against over-current and over-heating, thermal protection circuitry is provided.<br />
In addition, automatic idling circuit is provided to protect against thermal run-away.<br />
- BALANCED INPUT<br />
A balanced input is provided to reduce hum pick up from a long distance input cable and to avoid ground<br />
loop problem when you build the system.<br />
- USE OF EMERGENCY BATTERY<br />
You can operate this <strong>PA</strong> amplifier by using emergency battery for unexpected AC power failure.<br />
<strong>PA</strong>-<strong>2312</strong>
Front Panel Controls<br />
<strong>PA</strong>-<strong>2312</strong> PUBLIC ADDRESS 2 <strong>CH</strong> POWER AMPLIFIER<br />
1. POWER INDICATING LED<br />
This LED indicates power is turned ON.<br />
2. POWER SWIT<strong>CH</strong><br />
Pressing this switch to ON will make the power indicating LED ON and supply the power to unit.<br />
3. OUTPUT LEVEL INDICATORS<br />
These LEDs indicates the output level of this amplifier. Be sure not to operate the unit with the clip LED<br />
ON continuously (RED).<br />
4. PROTECTION INDICATOR<br />
This LED indicates the condition of the protection circuit. When the protection LED is “ON” the amplifier<br />
is not operating normally (overheating and limiting), please check the INPUT/OUTPUT condition of the<br />
amplifier.<br />
5. LEVEL ADJUSTMENT VOLUME<br />
This volumes control output levels.<br />
4<br />
<strong>CH</strong>ANNEL 1<br />
PROT<br />
CLIP<br />
-10dB<br />
-40dB<br />
11 10 9<br />
12<br />
8<br />
13<br />
7<br />
15<br />
6<br />
17<br />
5<br />
19<br />
4<br />
22<br />
3<br />
29<br />
2<br />
54<br />
1<br />
00<br />
0<br />
3<br />
5<br />
PUBLIC ADDRESS 2 <strong>CH</strong> POWER AMPLIFIER<br />
<strong>CH</strong>ANNEL 2<br />
PROT<br />
CLIP<br />
-10dB<br />
-40dB<br />
11 10 9<br />
12<br />
8<br />
13<br />
7<br />
15<br />
6<br />
17<br />
5<br />
19<br />
4<br />
22<br />
3<br />
29<br />
2<br />
54<br />
1<br />
00<br />
0<br />
2<br />
ON<br />
OFF<br />
POWER<br />
1<br />
<strong>PA</strong>-<strong>2312</strong> 3
PUBLIC ADDRESS RECEIVER<br />
Rear Panel Controls<br />
4<br />
3<br />
<strong>CH</strong> 1<br />
<strong>CH</strong> 2<br />
OUTPUT<br />
B<br />
22V ( 4Ω ) 70V ( 21Ω ) A<br />
COM<br />
100V ( 41Ω )<br />
1. FAN<br />
The fans should be kept free of all obstructions and be accessible to cool fresh air when possible. It is<br />
important that the fans be used in a dust free environment.<br />
2. SPEAKER OUTPUT TERMINALS<br />
These terminals are for connection of speaker lines to deliver power output to speakers. Impedance (voltages)<br />
of 4 ohm, 25V, 70V and 100V are provided for convenience. In any case, use the speakers<br />
whose combined impedance is equal to or higher than the rated output impedance of amplifier.<br />
* 100V or 25V can be selected optionally.<br />
3. AC INLET<br />
This terminal is connected AC input cord.<br />
4. FUSE DRAWER<br />
These fuse drawer contains AC fuse. Replace them with the same type fuse when they are blown out. If<br />
they continuously blow, stop replacing fuses and refer servicing to qualified personnel.<br />
5. HIGH-<strong>PA</strong>SS FILTER SWIT<strong>CH</strong><br />
This switch is for activating the High-pass Filter circuit, to protect speakers from excessive low frequency<br />
power demands. The -3dB frequency of the High-pass Filter is 400Hz.<br />
<strong>PA</strong>-1000B/1000BR<br />
2<br />
~AC INPUT<br />
230V 50Hz, 290W<br />
FUSE<br />
T4AL/250V<br />
<strong>CH</strong> 1<br />
ON<br />
<strong>CH</strong> 2<br />
ON<br />
HPF<br />
HPF<br />
CAUTION; TO REDUCE THE RISK OF FIRE<br />
REPLACE ONLY WITH SAME TYPE FUSE.<br />
UTILISER UN FUSIBLE DE RE<strong>CH</strong>ANGE<br />
DE MEME TYPE.<br />
CAUTION; TO REDUCE THE RISK OF ELE-<br />
CTRIC SHOCK, DO NOT REMOVE COVER.<br />
NO USER SERVICEABLE <strong>PA</strong>RTS INSIDE.<br />
REFER SERVICING TO QUALIFIED SERVICE<br />
PERSONNEL<br />
AVIS; RISQUE DE <strong>CH</strong>OC ELECTRIQUE NE<br />
<strong>PA</strong>S<br />
OUVRIR.<br />
OFF<br />
OFF<br />
BALANCED INPUT<br />
LINK<br />
FLOAT<br />
GROUND<br />
LIFT<br />
FRA ME<br />
MODEL NO. <strong>PA</strong>-<strong>2312</strong><br />
PUBLIC ADDRESS<br />
2 <strong>CH</strong> POWER AMPLIFIER<br />
OUTPUT POWER : 120WX2<br />
MADE IN KOREA<br />
+<br />
DC I NPUT<br />
24V<br />
4 5 6 7 8<br />
4Ω 25V 70V 100V<br />
22V 5.2Ω 42Ω 83Ω<br />
S N<br />
1
PUBLIC ADDRESS 2 <strong>CH</strong> POWER AMPLIFIER<br />
6. INPUT JACKS<br />
These input jacks and terminals are for the balanced input signal. You can connect amplifiers in parallel<br />
by using XLR jack.<br />
7. EARTH LINK SWIT<strong>CH</strong><br />
This slide switch provides for separation of “safety” earth and “safety” earth to prevent from hum loops.<br />
8. DC INPUT TERMINALS<br />
These terminals are for connecting DC power supply of battery. Connect red colored terminal to positive<br />
lead of battery and black colored one to negative lead of battery.<br />
<strong>PA</strong>-<strong>2312</strong><br />
5
PUBLIC ADDRESS 2 <strong>CH</strong> POWER AMPLIFIER<br />
Applications<br />
6 <strong>PA</strong>-<strong>2312</strong><br />
TURN TABLE<br />
(CD, TUNER.....)<br />
SWED 1 (2000W)<br />
SWED 2 (2000W)<br />
SWED 3 (2000W)<br />
<strong>CH</strong> 1<br />
<strong>CH</strong> 2<br />
OUTP UT<br />
B<br />
22V ( 4Ω ) 70V ( 21Ω ) A<br />
COM<br />
100V ( 41Ω )<br />
~AC INPUT<br />
230V 50Hz, 290W<br />
FUSE<br />
T4AL/250V<br />
( )<br />
( )<br />
S N<br />
<strong>CH</strong> 1<br />
ON<br />
<strong>CH</strong> 2<br />
ON<br />
HPF<br />
HPF<br />
(RACK ONLY)<br />
SWIT<strong>CH</strong>ED<br />
DC OUT 24V<br />
5A MAX<br />
UNSWED (700W)<br />
CAUTION; TO REDUCE THE RISK OF FIRE<br />
REPLACE ONLY WITH SAME TYPE FUSE.<br />
UTILISER UN FUSIBLE DE RE<strong>CH</strong>ANGE<br />
DE MEME TYPE.<br />
CAUTION; TO REDUCE THE RISK OF ELE-<br />
CTRIC SHOCK, DO NOT REMOVE COVER.<br />
NO USER SERVICEABLE <strong>PA</strong>RTS INSIDE.<br />
REFER SERVICING TO QUALIFIED SERVICE<br />
PERSONNEL.<br />
AVIS; RISQUE DE <strong>CH</strong>OC ELECTRIQUE NE<br />
<strong>PA</strong>S<br />
OUVRIR.<br />
OFF<br />
OFF<br />
<strong>CH</strong> 2<br />
BALANCED INPUT<br />
INSERT INSERT<br />
OUTPUT OUTPUT<br />
<strong>CH</strong> 1<br />
LINK<br />
AMP IN 1<br />
ALL<br />
AMP IN 2<br />
(AMP ONLY)<br />
SWIT<strong>CH</strong>ED DC OUT 24V<br />
( )<br />
BATTERY<br />
INPUT<br />
<strong>CH</strong> 12 <strong>CH</strong> 11 <strong>CH</strong> 10 <strong>CH</strong> 9<br />
( )<br />
FLOAT<br />
~ AC INPUT : 220V 60Hz, 139VA<br />
FUSE : 1A / 250V<br />
DC INPUT<br />
24V<br />
GROUND<br />
LIFT<br />
FRA ME<br />
GROUP 2<br />
GROUP 1 TIMER REMOTE<br />
LINE<br />
MODEL NO. <strong>PA</strong>-<strong>2312</strong><br />
PUBLIC ADDRESS<br />
2 <strong>CH</strong> POWER AMPLIFIER<br />
OUTPUT POWER : 120WX2<br />
MADE IN KOREA<br />
+<br />
DC I NPUT<br />
24V<br />
(+)<br />
(-)<br />
UNSWIT<strong>CH</strong>ED<br />
DC OUTPUT 24V REMOTE<br />
C-SW-H<br />
~AC INPUT<br />
220V/60Hz,217VA<br />
REC OUTPUT PRIORITY INPUT<br />
MUTE<br />
ON<br />
OFF<br />
LINE LINE LINE LINE LINE<br />
S<br />
N<br />
LINE<br />
PD-9359<br />
AC INPUT<br />
MODEL NO. PB-9207A<br />
BATTERY <strong>CH</strong>ARGER<br />
MADE IN KOREA<br />
BATTERY<br />
(DC24V)<br />
( )<br />
PP-9214<br />
MIC MIC MIC MIC MIC MIC MIC MIC<br />
<strong>CH</strong> 8 <strong>CH</strong> 7 <strong>CH</strong> 6<br />
S N<br />
HOT<br />
(+)<br />
<strong>CH</strong> 5 <strong>CH</strong> 4 <strong>CH</strong> 3 <strong>CH</strong> 2 <strong>CH</strong> 1<br />
(-)<br />
- +<br />
DC INPUT<br />
24V <strong>CH</strong> 16 <strong>CH</strong> 15 <strong>CH</strong> 14 <strong>CH</strong> 13 <strong>CH</strong> 12 <strong>CH</strong> 11 <strong>CH</strong> 10 <strong>CH</strong> 9<br />
EMERGENCY<br />
GND<br />
AC FUSE<br />
4A/250V<br />
DC FUSE<br />
10A/250V<br />
( )<br />
( )<br />
SPEAKER<br />
BATTERY IN<br />
( )<br />
( )<br />
S N<br />
<strong>CH</strong> 8 <strong>CH</strong> 7 <strong>CH</strong> 6 <strong>CH</strong> 5 <strong>CH</strong> 4 <strong>CH</strong> 3 <strong>CH</strong> 2 <strong>CH</strong> 1<br />
MIC<br />
PS-9116<br />
PB-9207A<br />
( )<br />
N<br />
BATTERY<br />
(DC24V)<br />
ON
Block Diagram<br />
PUBLIC ADDRESS 2 <strong>CH</strong> POWER AMPLIFIER<br />
<strong>PA</strong>-<strong>2312</strong><br />
7
PUBLIC ADDRESS 2 <strong>CH</strong> POWER AMPLIFIER<br />
Specifications ..........................................................0dB=0.775Vrms<br />
- ELECTRICAL<br />
Rated Output (THD 1%).......................................................................................................120W (RMS)<br />
..............................................................................................................................................4Ω (22V)<br />
...........................................................................................................................................5.2Ω (25V)<br />
............................................................................................................................................41Ω (70V)<br />
..........................................................................................................................................83Ω (100V)<br />
Input Sensitivity/Impedance..............................................................................................1V/10kΩ, BAL<br />
Frequency Response (+1/–3dB) ...........................................................................................70Hz-20kHz<br />
T.H.D .................................................................................................................................Less than 1%<br />
S/N .............................................................................................................................Better than 95dB<br />
HPF ................................................................................................................................–3dB at 400Hz<br />
Channel Separation .......................................................................................................Less than –70dB<br />
- GENERAL<br />
<strong>Power</strong> Source ..................................................................................AC 110V–240V, 50/60Hz, DC 24V<br />
<strong>Power</strong> Consumption .....................................................................................................................290W<br />
Weight..........................................................................................................................................20kg<br />
Dimensions ...............................................................................................482(W) 132(H) 280(D)mm<br />
* Specifications and design subject to change without notice for improvements.<br />
8 <strong>PA</strong>-<strong>2312</strong>