UMC 112 - Trend Product Marking Systems Australia

More documents

Recommendations

Info

Exhaust air silencer Clean the silencer (see page 5-4) Every 2000 operating hours. 1. With table or built-in unit: move the marking head completely upward. or - With hand-held units: turn the marking head upside down. 2. Switch off the control and pull the power supply plug. Depending on the unit type the marking head has one or 2 silencers: 1 Silencer 2 2 silencers in engraving units Marking head from the bottom Fig. 10194 3. Unscrew the silencer, wash it with warm water (max. 40 °C) and reassemble it. 4. If the silencer is very dirty: assemble a new silencer. B_PM_UMC112_en05.doc 5-6 Maintenance ÖSTLING Markiersysteme GmbH
Toothed belts of the axes (Coining unit) Check the toothed belts (see page 5-4) If necessary, i. e. if the slides (see page 5-9) are tight or with loss of quality of the marking. 1. Switch off the control and pull the power supply plug. 2. Unscrew the covering cap of the marking head. 1 Toothed belt of the X-axis 2 Eccentric screw for toothed belt of the X-axis 3 Fastening toothed belt of the X-axis 4 Eccentric screw for toothed belt of the Yaxis 5 Toothed belt of the Y-axis Marking head without covering cap Fig. 10195 3. Check the tension of the toothed belt. Toothed belt must sit tensely. Note Sometimes the toothed belt of the Y-axis is better accessible from down than from above. For that purpose turn the marking head upside down. 4. Check the toothed belt of the X- and Y-axis on wear. If the tension of the toothed belt is too low or a toothed belt is worn out, this toothed belt must be changed (see page 5-8). 5. Reassemble the covering cap of the marking head. B_PM_UMC112_en05.doc ÖSTLING Markiersysteme GmbH Maintenance 5-7
Page 1 and 2:
UMC 112 Ö S T L I N G Markiersyste
Page 3 and 4:
Table of contents Chapter 1 Safety
Page 5 and 6:
Chapter 5 Maintenance 7 System cont
Page 7 and 8:
Chapter 9 Drawings, parts lists Cha
Page 9 and 10:
Chapter 1 Safety 1 For your safety
Page 11 and 12:
3 Operational safety The marking sy
Page 13 and 14:
Duty to care in handling the markin
Page 15 and 16:
4 Dangers overview The following ch
Page 17 and 18:
Chapter 2 Set-up 1 Installation and
Page 19 and 20:
3. Tuck the 21-pin socket of the co
Page 21 and 22:
With vertical/lateral installation
Page 23 and 24:
Chapter 3 Description 1 Short descr
Page 25 and 26:
2.2 Control UMC 112 2.3 Software Co
Page 27 and 28:
Hand-held unit Built-in unit Combin
Page 29 and 30:
Combination unit with marking head
Page 31 and 32:
Engraving tool WE 1 R Art.-Nr. 45.4
Page 33 and 34:
Chapter 4 Operation 1 Operating dev
Page 35 and 36:
1 Operating devices The following o
Page 37 and 38:
2 Basics of operation Online help T
Page 39 and 40:
Switching off the control 1. Save a
Page 41 and 42:
Creating a new text field • Circl
Page 43 and 44:
7. Enter the character height of th
Page 45 and 46: 3.2 Working with wildcards Instead
Page 47 and 48: 3. Enter the following values: - "C
Page 49 and 50: 5. If desired, also special formats
Page 51 and 52: Fig. 10235en - "Enable prompt": fre
Page 53 and 54: 3.4 Saving masks 1. Create the mask
Page 55 and 56: 4. Enter file name you wish to give
Page 57 and 58: 5.2 Starting the marking 1. Select
Page 59 and 60: 6.2 Importing data Texts from files
Page 61 and 62: 7 System control 7.1 Reading out di
Page 63 and 64: • I/O Status: status of the input
Page 65 and 66: 5. To edit the I/O program: - Selec
Page 67 and 68: 7.4 Setting marking head parameters
Page 69 and 70: • Current: motor current in [mA].
Page 71 and 72: 7.6 Selecting the marking tool 1. S
Page 73 and 74: 7.7 Controlling the inputs and outp
Page 75 and 76: Selecting network settings 1. Selec
Page 77 and 78: • Number of marking: default how
Page 79 and 80: Displaying and sorting files for fi
Page 81 and 82: 7.9 Setting date and time 1. Select
Page 83 and 84: 7.10 Saving data on USB stick Furth
Page 85 and 86: 8.2 Further fonts This font is a pr
Page 87 and 88: Font 'lcom.chr' Fig. 10282 Font 'oc
Page 89 and 90: Font 'trip.chr' Fig. 10291 Font 'ts
Page 91 and 92: Chapter 5 Maintenance 1 General Gui
Page 93 and 94: 1.2 Lubricants For single-shift ope
Page 95: 2.2 Maintenance instructions Ventil
Page 99 and 100: Slides of the axes (Coining unit) C
Page 101 and 102: Adjust the nuts 6. Insert new batte
Page 103 and 104: 3 Pneumatic parts 3.1 Maintenance o
Page 105 and 106: Set the oiler If necessary. 1. Do n
Page 107 and 108: Chapter 6 Communication 1 Communica
Page 109 and 110: Parameter General remarks 3. To act
Page 111 and 112: Start marking The marking process s
Page 113 and 114: Load text With this function, text
Page 115 and 116: 1.2 PLC operation (option) Loading
Page 117 and 118: 2 Inputs and outputs with special f
Page 119 and 120: Chapter 7 Connector pin lists 1 Mar
Page 121 and 122: 1.2 Stepping motors Colour coding C
Page 123 and 124: 2.1 Socket BU1 to marking head The
Page 125 and 126: 2.3 Socket BU3 The socket BU3 for e
Page 127 and 128: 2.5 Socket BU4 2.6 Socket BU5 The s
Page 129 and 130: In- /output Name Remark E1.0 foot s
Page 131 and 132: 4 Serial port RS232 Serial communic
Page 133 and 134: Terminal strip on slide Cable Termi
Page 135 and 136: Chapter 8 Index B_PM_UMC112_en08.do
Page 137 and 138: Mode Edit mode.....................
Page 139 and 140: Chapter 9 Drawings, parts lists B_P
Page 141 and 142: Chapter 10 EU conformity explanatio
Page 143: - Machines 98/37/EG - Electromagnet
Page 146 and 147:
B_PM_UMC112_en11.doc 11-2 Request f
Page 149:
ÖSTLING Markiersysteme GmbH ÖSTLI
show all

UMC 112 - Trend Product Marking Systems Australia

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?