UMC 112 - Trend Product Marking Systems Australia
UMC 112 - Trend Product Marking Systems Australia UMC 112 - Trend Product Marking Systems Australia
4. When using a rotation axis: - Enter the diameter of the workpiece in [mm]. - Enter the position of the Y linear axis behind "Y position" or teach it with and . - Enter the resolution of the rotation axis behind "Steps/rev". - Select the rotating direction of the rotation axis behind "Rotation-Axis". 5. When using a Z-axis: - Enter the break delay in [ms]. - Select the home position of the Z-axis behind "Ini position". 6. Select "MotorCard 1" or "MotorCard 2". Mask "Markinghead Parameter", tab "MotorCard" Fig. 10661en Note When using 3 or 4 axes (options) the X motor is the rotation axis, the Y motor is the Z-axis. B_PM_UMC112_en04.doc 4-36 Operation ÖSTLING Markiersysteme GmbH
• Current: motor current in [mA]. • Boost: increase of the motor current in [mA] during ramping. • MaxPos: maximum position in [mm] the marking head can reach. Accords to the marking field. Example: 100 mm in X-direction, 50 mm in Y-direction for marking head 5/10. • mm/step: with coining heads: feed in [mm] after each drop of the coining tool. • Ramptime: time in [ms] during which the motor current is increased. • MaxV: travel speed of the marking head in X- or Y-direction in [mm/s] during deadhead. • HomeV: speed of the marking head in X- or Y-direction in [mm/s] during homing. • Overtravel: position of the initiator. An initiator is an inductive proximity switch. Distance of the initiator from home in [mm] in X- or Y-direction. • Limit Switch: displays if limit switch is a normally closed contact or a normally open contact. B_PM_UMC112_en04.doc ÖSTLING Markiersysteme GmbH Operation 4-37
- Page 17 and 18: Chapter 2 Set-up 1 Installation and
- Page 19 and 20: 3. Tuck the 21-pin socket of the co
- Page 21 and 22: With vertical/lateral installation
- Page 23 and 24: Chapter 3 Description 1 Short descr
- Page 25 and 26: 2.2 Control UMC 112 2.3 Software Co
- Page 27 and 28: Hand-held unit Built-in unit Combin
- Page 29 and 30: Combination unit with marking head
- Page 31 and 32: Engraving tool WE 1 R Art.-Nr. 45.4
- Page 33 and 34: Chapter 4 Operation 1 Operating dev
- Page 35 and 36: 1 Operating devices The following o
- Page 37 and 38: 2 Basics of operation Online help T
- Page 39 and 40: Switching off the control 1. Save a
- Page 41 and 42: Creating a new text field • Circl
- Page 43 and 44: 7. Enter the character height of th
- Page 45 and 46: 3.2 Working with wildcards Instead
- Page 47 and 48: 3. Enter the following values: - "C
- Page 49 and 50: 5. If desired, also special formats
- Page 51 and 52: Fig. 10235en - "Enable prompt": fre
- Page 53 and 54: 3.4 Saving masks 1. Create the mask
- Page 55 and 56: 4. Enter file name you wish to give
- Page 57 and 58: 5.2 Starting the marking 1. Select
- Page 59 and 60: 6.2 Importing data Texts from files
- Page 61 and 62: 7 System control 7.1 Reading out di
- Page 63 and 64: • I/O Status: status of the input
- Page 65 and 66: 5. To edit the I/O program: - Selec
- Page 67: 7.4 Setting marking head parameters
- Page 71 and 72: 7.6 Selecting the marking tool 1. S
- Page 73 and 74: 7.7 Controlling the inputs and outp
- Page 75 and 76: Selecting network settings 1. Selec
- Page 77 and 78: • Number of marking: default how
- Page 79 and 80: Displaying and sorting files for fi
- Page 81 and 82: 7.9 Setting date and time 1. Select
- Page 83 and 84: 7.10 Saving data on USB stick Furth
- Page 85 and 86: 8.2 Further fonts This font is a pr
- Page 87 and 88: Font 'lcom.chr' Fig. 10282 Font 'oc
- Page 89 and 90: Font 'trip.chr' Fig. 10291 Font 'ts
- Page 91 and 92: Chapter 5 Maintenance 1 General Gui
- Page 93 and 94: 1.2 Lubricants For single-shift ope
- Page 95 and 96: 2.2 Maintenance instructions Ventil
- Page 97 and 98: Toothed belts of the axes (Coining
- Page 99 and 100: Slides of the axes (Coining unit) C
- Page 101 and 102: Adjust the nuts 6. Insert new batte
- Page 103 and 104: 3 Pneumatic parts 3.1 Maintenance o
- Page 105 and 106: Set the oiler If necessary. 1. Do n
- Page 107 and 108: Chapter 6 Communication 1 Communica
- Page 109 and 110: Parameter General remarks 3. To act
- Page 111 and 112: Start marking The marking process s
- Page 113 and 114: Load text With this function, text
- Page 115 and 116: 1.2 PLC operation (option) Loading
- Page 117 and 118: 2 Inputs and outputs with special f
4. When using a rotation axis:<br />
- Enter the diameter of the workpiece in [mm].<br />
- Enter the position of the Y linear axis behind "Y position" or teach it<br />
with and .<br />
- Enter the resolution of the rotation axis behind "Steps/rev".<br />
- Select the rotating direction of the rotation axis behind "Rotation-Axis".<br />
5. When using a Z-axis:<br />
- Enter the break delay in [ms].<br />
- Select the home position of the Z-axis behind "Ini position".<br />
6. Select "MotorCard 1" or "MotorCard 2".<br />
Mask "<strong>Marking</strong>head Parameter", tab "MotorCard" Fig. 10661en<br />
Note<br />
When using 3 or 4 axes (options) the X motor is the rotation axis, the Y<br />
motor is the Z-axis.<br />
B_PM_<strong>UMC</strong><strong>112</strong>_en04.doc<br />
4-36 Operation ÖSTLING Markiersysteme GmbH