UMC 112 - Trend Product Marking Systems Australia

More documents

Recommendations

Info

The document was written in the Technical documentation department of the company ÖSTLING Markiersysteme GmbH. All rights at this documentation, in particular the right of the duplication and spreading as well as the translation are at ÖSTLING Markiersysteme GmbH, also for the case of patent right registrations. No part of the documentation may be reproduced in any form without previous written agreement of the company ÖSTLING Markiersysteme GmbH or processed, multiplied or spread using electronic systems. Mistake and technical subject to change. © ÖSTLING Markiersysteme GmbH ÖSTLING Markiersysteme GmbH is not responsible for any errors in this documentation. A liability for indirect and direct damage, which develops in connection with the supply or the use of this documentation, is impossible, as far as this is legally permissible.
Table of contents Chapter 1 Safety Chapter 2 Set-up Chapter 3 Description 1 For your safety ......................................................................................... 1-2 2 Definitions................................................................................................. 1-2 3 Operational safety.................................................................................... 1-3 3.1 Intended use of the marking system ....................................................... 1-3 3.2 Measures taken by the user/operator ..................................................... 1-4 Consider warning plates and references.............................................. 1-4 Personnel instruction............................................................................ 1-4 Duty to care in handling the marking system ....................................... 1-5 Use of intended spare parts and operational funds ............................. 1-5 3.3 Measures taken by the manufacturer ..................................................... 1-6 4 Dangers overview..................................................................................... 1-7 1 Installation and Set-up of the Marking System ..................................... 2-2 1.1 Built-in units............................................................................................. 2-4 2 Measures to prevent electronic interference ........................................ 2-5 2.1 Complying with interference suppression as per CE .............................. 2-6 1 Short description...................................................................................... 3-2 2 Technical data .......................................................................................... 3-2 2.1 Marking units ........................................................................................... 3-2 2.2 Control UMC 112 .................................................................................... 3-3 2.3 Software .................................................................................................. 3-3 B_PM_UMC112_en00.doc ÖSTLING Markiersysteme GmbH Table of contents 0-3
Page 1: UMC 112 Ö S T L I N G Markiersyste
Page 5 and 6: Chapter 5 Maintenance 7 System cont
Page 7 and 8: Chapter 9 Drawings, parts lists Cha
Page 9 and 10: Chapter 1 Safety 1 For your safety
Page 11 and 12: 3 Operational safety The marking sy
Page 13 and 14: Duty to care in handling the markin
Page 15 and 16: 4 Dangers overview The following ch
Page 17 and 18: Chapter 2 Set-up 1 Installation and
Page 19 and 20: 3. Tuck the 21-pin socket of the co
Page 21 and 22: With vertical/lateral installation
Page 23 and 24: Chapter 3 Description 1 Short descr
Page 25 and 26: 2.2 Control UMC 112 2.3 Software Co
Page 27 and 28: Hand-held unit Built-in unit Combin
Page 29 and 30: Combination unit with marking head
Page 31 and 32: Engraving tool WE 1 R Art.-Nr. 45.4
Page 33 and 34: Chapter 4 Operation 1 Operating dev
Page 35 and 36: 1 Operating devices The following o
Page 37 and 38: 2 Basics of operation Online help T
Page 39 and 40: Switching off the control 1. Save a
Page 41 and 42: Creating a new text field • Circl
Page 43 and 44: 7. Enter the character height of th
Page 45 and 46: 3.2 Working with wildcards Instead
Page 47 and 48: 3. Enter the following values: - "C
Page 49 and 50: 5. If desired, also special formats
Page 51 and 52: Fig. 10235en - "Enable prompt": fre
Page 53 and 54:
3.4 Saving masks 1. Create the mask
Page 55 and 56:
4. Enter file name you wish to give
Page 57 and 58:
5.2 Starting the marking 1. Select
Page 59 and 60:
6.2 Importing data Texts from files
Page 61 and 62:
7 System control 7.1 Reading out di
Page 63 and 64:
• I/O Status: status of the input
Page 65 and 66:
5. To edit the I/O program: - Selec
Page 67 and 68:
7.4 Setting marking head parameters
Page 69 and 70:
• Current: motor current in [mA].
Page 71 and 72:
7.6 Selecting the marking tool 1. S
Page 73 and 74:
7.7 Controlling the inputs and outp
Page 75 and 76:
Selecting network settings 1. Selec
Page 77 and 78:
• Number of marking: default how
Page 79 and 80:
Displaying and sorting files for fi
Page 81 and 82:
7.9 Setting date and time 1. Select
Page 83 and 84:
7.10 Saving data on USB stick Furth
Page 85 and 86:
8.2 Further fonts This font is a pr
Page 87 and 88:
Font 'lcom.chr' Fig. 10282 Font 'oc
Page 89 and 90:
Font 'trip.chr' Fig. 10291 Font 'ts
Page 91 and 92:
Chapter 5 Maintenance 1 General Gui
Page 93 and 94:
1.2 Lubricants For single-shift ope
Page 95 and 96:
2.2 Maintenance instructions Ventil
Page 97 and 98:
Toothed belts of the axes (Coining
Page 99 and 100:
Slides of the axes (Coining unit) C
Page 101 and 102:
Adjust the nuts 6. Insert new batte
Page 103 and 104:
3 Pneumatic parts 3.1 Maintenance o
Page 105 and 106:
Set the oiler If necessary. 1. Do n
Page 107 and 108:
Chapter 6 Communication 1 Communica
Page 109 and 110:
Parameter General remarks 3. To act
Page 111 and 112:
Start marking The marking process s
Page 113 and 114:
Load text With this function, text
Page 115 and 116:
1.2 PLC operation (option) Loading
Page 117 and 118:
2 Inputs and outputs with special f
Page 119 and 120:
Chapter 7 Connector pin lists 1 Mar
Page 121 and 122:
1.2 Stepping motors Colour coding C
Page 123 and 124:
2.1 Socket BU1 to marking head The
Page 125 and 126:
2.3 Socket BU3 The socket BU3 for e
Page 127 and 128:
2.5 Socket BU4 2.6 Socket BU5 The s
Page 129 and 130:
In- /output Name Remark E1.0 foot s
Page 131 and 132:
4 Serial port RS232 Serial communic
Page 133 and 134:
Terminal strip on slide Cable Termi
Page 135 and 136:
Chapter 8 Index B_PM_UMC112_en08.do
Page 137 and 138:
Mode Edit mode.....................
Page 139 and 140:
Chapter 9 Drawings, parts lists B_P
Page 141 and 142:
Chapter 10 EU conformity explanatio
Page 143:
- Machines 98/37/EG - Electromagnet
Page 146 and 147:
B_PM_UMC112_en11.doc 11-2 Request f
Page 149:
ÖSTLING Markiersysteme GmbH ÖSTLI
show all

UMC 112 - Trend Product Marking Systems Australia

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?