The Army Maintenance Management System (TAMMS) Users Manual

More documents

Recommendations

Info

1. Use the same worksheet for more than 1 day. If no faults are found during the BEFORE OPERATION checks in the PMCS, write the calendar date under the fault description column. 2. When no faults are found, this worksheet can be used for more than 1 day even if the worksheet was used for concurrent PMCSs; that is, W/M. Just place the first letter of the type of PMCS performed (W/M) under the corrective action column by that day’s date in the fault description column. CURRENT READING and PUBLICATION (with changes). These are retrieved from the equipment data file. No entries from the operator/crew chief are needed in these areas. INSPECTOR’S LIC #. A space for the inspector to enter their license number (first letter of last name and last four of SSN) and the time of inspection completion. SIGNATURE and TIME. When a deficiency or shortcoming is found, the signature and time of operator or supervisor are required. This signature keeps the form from being used past current dispatch. The commander or the commander’s designated representative signs name and enters rank when making a status symbol change, or when changing from an X to a CIRCLED X (E) status symbol for a onetime operation. TIME. Leave blank or use as needed locally. For missile systems/subsystems reported under AR 700–138, enter the time when a deficiency was found. PARTS REQUESTED. The system checks the Document Control Register and prints any parts that have been ordered against the admin number on the worksheet. Operator/crew chiefs and supervisors review this section and take appropriate action as required. For more information about this section, see the AISM 25–L3Q–AWC–ZZZ–EM. FAULT. The fault number for which the part is requested. DOC NUMBER. The document number under which the required part has been ordered. NIIN. National Item Identification Number. NOUN. Part nomenclature. QTY DUE/REC. Due-in quantity for the part on order or the quantity received. STATUS DATE. The date of status code. DATE COMP. The date that all parts were received for document number listed or transaction closed. PRI. The priority for item ordered. DLC. Deadline code. D if deadlined; N if not deadlined. MAINTENANCE FAULTS. 1. ITEM NUM. Write the PMCS item number that applies to the fault listed in this column. If the PMCS has no item numbers, list the page, paragraph, or sequence number. Circle the number if fault is listed in the “Equipment is not ready/available if” column or “Not Mission Capable if” column of the PMCS. If the PMCS has no ready/available or NMC column, circle the TM item number, page, or paragraph number of any fault that makes equipment NMC. Pubs or TM sections other than PMCS may be required for safety faults or local dispatching. For example, AR 385–55 lists safety checks that may not be in the PMCS. Those faults are not counted as NMC for Materiel Condition Status Report reporting unless they are in the PMCS not ready column or the NMC column. But, list them if a problem is found with one of them. For those faults not covered by the PMCS, leave this column blank. FAULT DATE. Enter the calendar date the deficiency or shortcoming was found. FAULT STATUS. Enter the status symbol that applies to the fault or deficiency. FAULT DESCRIPTION. Repair of status symbol X faults cannot be postponed or delayed, but they may be changed to CIRCLED X status symbol for limited operation. The commander or the commander’s designated representative may change an X status symbol fault to a CIRCLED X status symbol. Changing of status symbols should only be done when the equipment is crucial to the mission. No X status symbol faults are changed to a CIRCLED X if it endangers the operator/crew or may cause further damage to the equipment. CIRCLED X conditions are for one-time operation or mission (common sense must be used). 1. If a fault can be repaired, stop the PMCS and correct the fault. Do not enter faults that have been repaired or already listed on the worksheet. Continue the PMCS to make sure no other faults exist. 2. Briefly describe fault. Skip one or two lines between faults. This gives maintenance room to note actions they take. 3. When more than one TM covers the equipment, draw a line under the last entry for one TM. Under the line, write the TM number of the manual to be used next. After the PMCS is finished and all faults that could not be fixed are listed, give the form to the maintenance supervisor. CORRECTIVE ACTION. Explain corrective actions taken. 1. Print Cleared for Limited Operations. Provide the specific limits under which equipment can be operated. For example, limits may involve speed, type of mission, distance, weather, or time. The change may affect a subsystem of a system listed in AR 700–138. If so, make sure limits include that part of the mission the system can no longer do. 2. Deficiencies changed to a CIRCLED X return to an X status symbol at the end of the day or mission. 3. Equipment cleared for limited operations is still carried as NMC for the Materiel Condition Status Reporting. 4. When a deficiency is corrected or changed to a CIRCLED X, enter the miles and calendar date in the corrective action column at the end of the dispatch or operation. 5. OPER HRS LIC #. The hours are posted in tenths and are only used when faults are corrected. The license number identifies the individual that corrected a fault or identified a fault. Figure 3–24. Sample DA Form 5988–E used for operator/crew PMCS 78 DA PAM 750–8 22 August 2005
Notes: 1 Administrative/bumper number is placed in upper right hand corner or as prescribed by local SOP. Legend for Figure 3–25; completion instructions follow. 1. ORGANIZATION. Enter the name of the unit to which the equipment belongs. 2. NOMENCLATURE AND MODEL. Figure 3–25. Sample DA Form 2404 used for operator/crew PMCS (fault noted) DA PAM 750–8 22 August 2005 79
Page 1 and 2:
UNCLASSIFIED Department of the Army
Page 3:
o Rescinds U.S. Army Communications
Page 6 and 7:
Contents—Continued General instru
Page 8 and 9:
Contents—Continued E. Department
Page 10 and 11:
Contents—Continued Figure 4-2: DD
Page 12 and 13:
Contents—Continued Figure E-2: Id
Page 15 and 16:
Chapter 1 Introduction 1-1. Purpose
Page 17 and 18:
(3) Historical processes, forms, re
Page 19 and 20:
equipment keep the data, reports, f
Page 21 and 22:
(3) Alert dispatch, DA Form 5987-1-
Page 23 and 24:
equipment as generators, air compre
Page 25 and 26:
Figure 2-1. Sample DA Form 348 (fro
Page 27 and 28:
PERMIT NUMBER (Initial). Enter the
Page 29 and 30:
DODAAC. Displays the DODAAC and uni
Page 31 and 32:
Legend for Figure 2-4; completion i
Page 33 and 34:
Notes: 1 Operator and supervisor or
Page 35 and 36:
DATE DISPATCHED. The date equipment
Page 37 and 38:
EQUIPMENT DATA. Administrative numb
Page 39 and 40:
REGISTRATION NO./SERIAL NO. The dis
Page 41 and 42: Notes: 1 More than one component on
Page 43 and 44: 1. The person in charge of the equi
Page 45 and 46: 1. The dispatcher prints the name o
Page 47 and 48: Legend for Figure 2-13; completion
Page 49 and 50: j. This chapter provides procedures
Page 51 and 52: (1) Purpose. DA Form 5410 is used t
Page 53 and 54: pamphlet. Explain those symbols or
Page 55 and 56: mileage/kilometers or hours in a 12
Page 57 and 58: (1) Units using ULLS-G use the comp
Page 59 and 60: conditions for inoperative equipmen
Page 61 and 62: ack to the organization as a receip
Page 63 and 64: (1) Copy one is kept by the owning
Page 65 and 66: Table 3-3. List of SNT reportable i
Page 67 and 68: (k) Certification or decertificatio
Page 69 and 70: 5. SERIAL NUMBER OF DEADLINED ITEM.
Page 71 and 72: Legend for Figure 3-4; completion i
Page 73 and 74: equired and AOE procedures are used
Page 75 and 76: ORG WON/DOC. The organizational wor
Page 79 and 80: Notes: 1 A system DD 314 is needed
Page 81 and 82: Figure 3-13. Sample DD Form 314 sub
Page 87 and 88: Figure 3-19. Sample DD Form 314 com
Page 89 and 90: Figure 3-21. Sample DD Form 314 use
Page 91: Legend for Figure 3-24; completion
Page 95 and 96: Notes: 1 Administrative number/bump
Page 97 and 98: INITIAL WHEN CORRECTED. The person
Page 99 and 100: a. Enter the noun abbreviation and
Page 101 and 102: . The operator/crew chief must ensu
Page 103 and 104: 1. ORGANIZATION. Enter the name of
Page 105 and 106: 2. NOMENCLATURE AND MODEL. a. Enter
Page 107 and 108: Legend for Figure 3-32; Completion
Page 109 and 110: Notes: 1 Status code, date, and tim
Page 111 and 112: Notes: 1 DA Form 3999-4 has four bl
Page 113 and 114: PHONE. Displays the phone number of
Page 115 and 116: SECTION I—CUSTOMER DATA. Blocks 1
Page 119 and 120: 38d. TIME. Enter the military time
Page 121 and 122: Legend for Figure 3-40; Completion
Page 123 and 124: 36d. TIME. Enter the military time
Page 125 and 126: SECTION IV—TASK REQUIREMENTS DATA
Page 127 and 128: 3c. PHONE NO. Enter the phone numbe
Page 129 and 130: Notes: 1 When used as a DA Form 240
Page 131 and 132: 5. If the delay is for a shop backu
Page 135 and 136: UIC SUPPORT. Support unit UIC. UNIT
Page 137 and 138: UIC’s SELECTED FOR THIS REPORT. E
Page 139 and 140: g. Contamination is a problem that
Page 143 and 144:
Page 145 and 146:
c. This form is used to figure the
Page 147 and 148:
4. In column 11, PCW (previously co
Page 149 and 150:
Table 5-1 Data input format (accept
Page 151 and 152:
Table 5-4 Data input format (transf
Page 153 and 154:
(a) “Permanent Log Book Copy” i
Page 155 and 156:
5-11. Records that go with equipmen
Page 157 and 158:
Cumulative EFC RDS g. Add the numbe
Page 159 and 160:
EFC RDS Fired e. Leave blank. Cumul
Page 161 and 162:
6. RDS/EFC COMPUTATION. Leave blank
Page 163 and 164:
a. For all nontactical wheeled vehi
Page 165 and 166:
10. REGISTRATION NO. a. Enter the r
Page 167 and 168:
c. For watercraft, enter the regist
Page 169 and 170:
13. CONTRACT NO. Enter the contract
Page 171 and 172:
Legend for Figure 5-12; completion
Page 173 and 174:
a. Enter the complete serial number
Page 175 and 176:
. If no registration number has bee
Page 177 and 178:
Legend for Figure 5-15; completion
Page 179 and 180:
Notes: 1 Use block 21 to note any u
Page 181 and 182:
6-4. Request for disposition and/or
Page 183 and 184:
Page 185 and 186:
28. STERN FRAME/SKEG/KORT NOZZLE. E
Page 187 and 188:
(3) Send the third copy to Commande
Page 189 and 190:
INSTALLATION. Assigned location. A
Page 191 and 192:
SHOP. Name of installation. CLASS.
Page 193 and 194:
Page 195 and 196:
c. The Joint Munitions Command and
Page 197 and 198:
Page 199 and 200:
(2) Deficiencies due to design, man
Page 201 and 202:
(2) DA or the manufacturer, command
Page 203 and 204:
Notes: 1 Sketches and pictures shou
Page 205 and 206:
22. DETAILS. Enter the following in
Page 207 and 208:
1a. FROM (Originator). In addition
Page 209 and 210:
Figure 10-3. Sample Category I SF 3
Page 211 and 212:
TO. Enter the command message addre
Page 213 and 214:
Figure 10-5. Sample DD Form 2332 (f
Page 215 and 216:
Appendix A References Section I Req
Page 217 and 218:
AR 750-6 Ground Safety Notification
Page 219 and 220:
DA Form 2404 Equipment Inspection a
Page 221 and 222:
DA Form 3266-2 Missile Materiel Con
Page 223 and 224:
Table B-1 Failure codes, alphabetic
Page 225 and 226:
Table B-1 Failure codes, alphabetic
Page 227 and 228:
Table B-2 Failure codes, numerical
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Table B-6 Utilization codes—Conti
Page 235 and 236:
Table B-11 Vehicle use codes Code D
Page 237 and 238:
Table B-18 Equipment category codes
Page 239 and 240:
Page 241 and 242:
Page 243 and 244:
Page 245 and 246:
Page 247 and 248:
Page 249 and 250:
Table B-20 Type maintenance request
Page 251 and 252:
Table B-21 Work request status code
Page 253 and 254:
Appendix C Warranty Control offices
Page 255 and 256:
Table C-2. Supporting logistics ass
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Table D-1 Julian/ordinal date calen
Page 263 and 264:
Figure E-1. Identification of requi
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Glossary Section I Abbreviations AC
Page 313 and 314:
DSN Defense Switched Network DSU di
Page 315 and 316:
MWO modification work order NBC nuc
Page 317 and 318:
SSN Social Security number STAMIS S
Page 319 and 320:
assembly A combination of component
Page 321 and 322:
line replaceable unit A combination
Page 323 and 324:
on-site maintenance Maintenance aut
Page 325 and 326:
system A combination of equipment e
show all

The Army Maintenance Management System (TAMMS) Users Manual

Create successful ePaper yourself

Delete template?

Save as template?