The Army Maintenance Management System (TAMMS) Users Manual

More documents

Recommendations

Info

Table B–2 Failure codes, numerical—Continued 649 Sweep malfunction 660 Stripped 664 Tension incorrect 670 Unbalanced 680 Unstable 688 Improper energy response 689 Improper source output 690 Vibration excessive 692 Video faulty 693 Audio faulty 695 Sync absent or incorrect 701 Warped 703 Improper amplitude 705 Beyond specified tolerance 710 Bearing or bushing failure 717 Accident damage 720 Brush failure/worn excessively 722 Weld cracked, broken or defective 730 Loose 731 Battle damage 734 Rise time incorrect 740 Saturation resistance high 748 Frequency, erratic or incorrect 780 Bent 790 Out of adjustment includes out of tolerance/calibration 799 No defect 807 Servo mag amp time constant 816 Total impedance, high 817 Total impedance, low 840 Seized 844 Corona effect 845 Crystallized 846 Delaminated 855 Heat damage 900 Burned, includes charred 908 Miswired 910 Chipped 916 Impending or incipient failure indicated by spectrometric oil analysis 927 Pinched 935 Scored 945 Structural failure 947 Torn 964 Poor spectrum 216 DA PAM 750–8 22 August 2005
Table B–2 Failure codes, numerical—Continued 968 Dioding 977 Pressure incorrect 999 Drive/disk failure/crash (computers) Table B–3 Failure detected during codes Code Description A Scheduled maintenance B Handling C Test D Normal operation E Storage F Inspection G Flight H Other J Calibration Table B–4 First indication of trouble codes Code Description 008 Noisy 068 Inoperative 258 Overheating 387 Low performance 790 Out of adjustment 360 Intermittent 432 Off frequency 680 Unstable 077 Accident 777 Mid-service life 099 Other Table B–5 Action codes Code Description A Replaced. This code is used when an item (repair parts, components, and so on) is removed and replaced concurrently (or at a later time) by a like or an equivalent item (except for gun/howitzer tubes and hourmeters/odometers, see codes W and X). For the purpose of avionics, when the equivalent item changes the avionic system designation, use action codes "R" and "S" in lieu of action code "A." B Adjusted. This code is used when tightening, adjusting, bleeding, rigging or activating reset buttons or switches, regulating, and so on. C Repaired. This code is used when a reparable item is repaired. This includes, but is not limited to, disassembly, cleaning incidental to repair action, inspection, adjustment, internal lubrication, replacement of integral parts, assemblies and sub-assemblies, and welding. DA PAM 750–8 22 August 2005 217
Page 1 and 2:
UNCLASSIFIED Department of the Army
Page 3:
o Rescinds U.S. Army Communications
Page 6 and 7:
Contents—Continued General instru
Page 8 and 9:
Contents—Continued E. Department
Page 10 and 11:
Contents—Continued Figure 4-2: DD
Page 12 and 13:
Contents—Continued Figure E-2: Id
Page 15 and 16:
Chapter 1 Introduction 1-1. Purpose
Page 17 and 18:
(3) Historical processes, forms, re
Page 19 and 20:
equipment keep the data, reports, f
Page 21 and 22:
(3) Alert dispatch, DA Form 5987-1-
Page 23 and 24:
equipment as generators, air compre
Page 25 and 26:
Figure 2-1. Sample DA Form 348 (fro
Page 27 and 28:
PERMIT NUMBER (Initial). Enter the
Page 29 and 30:
DODAAC. Displays the DODAAC and uni
Page 31 and 32:
Legend for Figure 2-4; completion i
Page 33 and 34:
Notes: 1 Operator and supervisor or
Page 35 and 36:
DATE DISPATCHED. The date equipment
Page 37 and 38:
EQUIPMENT DATA. Administrative numb
Page 39 and 40:
REGISTRATION NO./SERIAL NO. The dis
Page 41 and 42:
Notes: 1 More than one component on
Page 43 and 44:
1. The person in charge of the equi
Page 45 and 46:
1. The dispatcher prints the name o
Page 47 and 48:
Legend for Figure 2-13; completion
Page 49 and 50:
j. This chapter provides procedures
Page 51 and 52:
(1) Purpose. DA Form 5410 is used t
Page 53 and 54:
pamphlet. Explain those symbols or
Page 55 and 56:
mileage/kilometers or hours in a 12
Page 57 and 58:
(1) Units using ULLS-G use the comp
Page 59 and 60:
conditions for inoperative equipmen
Page 61 and 62:
ack to the organization as a receip
Page 63 and 64:
(1) Copy one is kept by the owning
Page 65 and 66:
Table 3-3. List of SNT reportable i
Page 67 and 68:
(k) Certification or decertificatio
Page 69 and 70:
5. SERIAL NUMBER OF DEADLINED ITEM.
Page 71 and 72:
Page 73 and 74:
equired and AOE procedures are used
Page 75 and 76:
ORG WON/DOC. The organizational wor
Page 77 and 78:
Page 79 and 80:
Notes: 1 A system DD 314 is needed
Page 81 and 82:
Figure 3-13. Sample DD Form 314 sub
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Figure 3-19. Sample DD Form 314 com
Page 89 and 90:
Figure 3-21. Sample DD Form 314 use
Page 91 and 92:
Page 93 and 94:
Notes: 1 Administrative/bumper numb
Page 95 and 96:
Notes: 1 Administrative number/bump
Page 97 and 98:
INITIAL WHEN CORRECTED. The person
Page 99 and 100:
a. Enter the noun abbreviation and
Page 101 and 102:
. The operator/crew chief must ensu
Page 103 and 104:
1. ORGANIZATION. Enter the name of
Page 105 and 106:
2. NOMENCLATURE AND MODEL. a. Enter
Page 107 and 108:
Legend for Figure 3-32; Completion
Page 109 and 110:
Notes: 1 Status code, date, and tim
Page 111 and 112:
Notes: 1 DA Form 3999-4 has four bl
Page 113 and 114:
PHONE. Displays the phone number of
Page 115 and 116:
SECTION I—CUSTOMER DATA. Blocks 1
Page 117 and 118:
Page 119 and 120:
38d. TIME. Enter the military time
Page 121 and 122:
Legend for Figure 3-40; Completion
Page 123 and 124:
36d. TIME. Enter the military time
Page 125 and 126:
SECTION IV—TASK REQUIREMENTS DATA
Page 127 and 128:
3c. PHONE NO. Enter the phone numbe
Page 129 and 130:
Notes: 1 When used as a DA Form 240
Page 131 and 132:
5. If the delay is for a shop backu
Page 133 and 134:
Page 135 and 136:
UIC SUPPORT. Support unit UIC. UNIT
Page 137 and 138:
UIC’s SELECTED FOR THIS REPORT. E
Page 139 and 140:
g. Contamination is a problem that
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
c. This form is used to figure the
Page 147 and 148:
4. In column 11, PCW (previously co
Page 149 and 150:
Table 5-1 Data input format (accept
Page 151 and 152:
Table 5-4 Data input format (transf
Page 153 and 154:
(a) “Permanent Log Book Copy” i
Page 155 and 156:
5-11. Records that go with equipmen
Page 157 and 158:
Cumulative EFC RDS g. Add the numbe
Page 159 and 160:
EFC RDS Fired e. Leave blank. Cumul
Page 161 and 162:
6. RDS/EFC COMPUTATION. Leave blank
Page 163 and 164:
a. For all nontactical wheeled vehi
Page 165 and 166:
10. REGISTRATION NO. a. Enter the r
Page 167 and 168:
c. For watercraft, enter the regist
Page 169 and 170:
13. CONTRACT NO. Enter the contract
Page 171 and 172:
Page 173 and 174:
a. Enter the complete serial number
Page 175 and 176:
. If no registration number has bee
Page 177 and 178:
Page 179 and 180: Notes: 1 Use block 21 to note any u
Page 181 and 182: 6-4. Request for disposition and/or
Page 183 and 184: Legend for Figure 6-1; completion i
Page 185 and 186: 28. STERN FRAME/SKEG/KORT NOZZLE. E
Page 187 and 188: (3) Send the third copy to Commande
Page 189 and 190: INSTALLATION. Assigned location. A
Page 191 and 192: SHOP. Name of installation. CLASS.
Page 195 and 196: c. The Joint Munitions Command and
Page 199 and 200: (2) Deficiencies due to design, man
Page 201 and 202: (2) DA or the manufacturer, command
Page 203 and 204: Notes: 1 Sketches and pictures shou
Page 205 and 206: 22. DETAILS. Enter the following in
Page 207 and 208: 1a. FROM (Originator). In addition
Page 209 and 210: Figure 10-3. Sample Category I SF 3
Page 211 and 212: TO. Enter the command message addre
Page 213 and 214: Figure 10-5. Sample DD Form 2332 (f
Page 215 and 216: Appendix A References Section I Req
Page 217 and 218: AR 750-6 Ground Safety Notification
Page 219 and 220: DA Form 2404 Equipment Inspection a
Page 221 and 222: DA Form 3266-2 Missile Materiel Con
Page 223 and 224: Table B-1 Failure codes, alphabetic
Page 225 and 226: Table B-1 Failure codes, alphabetic
Page 227 and 228: Table B-2 Failure codes, numerical
Page 229: Table B-2 Failure codes, numerical
Page 233 and 234: Table B-6 Utilization codes—Conti
Page 235 and 236: Table B-11 Vehicle use codes Code D
Page 237 and 238: Table B-18 Equipment category codes
Page 249 and 250: Table B-20 Type maintenance request
Page 251 and 252: Table B-21 Work request status code
Page 253 and 254: Appendix C Warranty Control offices
Page 255 and 256: Table C-2. Supporting logistics ass
Page 261 and 262: Table D-1 Julian/ordinal date calen
Page 263 and 264: Figure E-1. Identification of requi
Page 281 and 282:
Figure E-2. Identification of requi
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
Page 309 and 310:
Page 311 and 312:
Glossary Section I Abbreviations AC
Page 313 and 314:
DSN Defense Switched Network DSU di
Page 315 and 316:
MWO modification work order NBC nuc
Page 317 and 318:
SSN Social Security number STAMIS S
Page 319 and 320:
assembly A combination of component
Page 321 and 322:
line replaceable unit A combination
Page 323 and 324:
on-site maintenance Maintenance aut
Page 325 and 326:
system A combination of equipment e
show all

The Army Maintenance Management System (TAMMS) Users Manual

Create successful ePaper yourself

Delete template?

Save as template?