Balinit
Balinit
Balinit
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
BALINIT ®<br />
guarantees superb results<br />
in punching and forming
The success formula for efficiency<br />
in punching and forming<br />
BALINIT ® hard coatings are only a few<br />
thousandths of a millimetre thick, but<br />
harder than steel and chemically inert.<br />
That’s why they sustainably reduce tool<br />
wear, cold welding and friction. More<br />
and more companies rely on BALINIT ®<br />
in their punching and forming operations<br />
to boost productivity and quality.<br />
02<br />
Lower costs<br />
- due to less tool wear<br />
- reduced lubricant consumption<br />
- fewer tool failures<br />
- calculable tool changes<br />
The result: you cut manufacturing<br />
costs across the board.<br />
Greater productivity<br />
- due to substantially longer lives<br />
- higher cycle frequencies<br />
- reduced machine idle time<br />
- less workpiece finishing effort<br />
The result: you can punch, form and<br />
fine-blank with greater cost-effectiveness.<br />
BALINIT ® hard coatings developed by Oerlikon Balzers are applied in vacuum processes at temperatures between<br />
200 and 500 °C. They considerably increase surface hardness and feature exceptional wear resistance and good<br />
sliding properties. Even after coating, tools fulfil all requirements relative to dimensional accuracy and edge sharpness.<br />
Higher quality<br />
- due to smoother surfaces<br />
- better dimensional stability<br />
- higher degrees of metal deformation<br />
- fewer manufacturing steps<br />
The result: you can establish higher<br />
standards in manufacturing.<br />
Less environmental impact<br />
- due to the use of environmentally<br />
friendlier lubricants<br />
- reduced lubricant consumption or<br />
even dry machining<br />
The result: you conserve resources<br />
and spend less on consumables.<br />
Cover picture: Feintool Technologie AG Lyss / CH
You cut costs across the board<br />
Less is more – particularly in the context<br />
of tool wear. Here, the remarkable<br />
hardness of BALINIT ® coatings makes<br />
a tangible contribution to cost savings<br />
in several respects.<br />
Cost factor: wear<br />
BALINIT ® protects the functional surfaces,<br />
cutting edges and drawing radii<br />
of punching and forming tools against<br />
abrasive wear. Thus, tools coated by<br />
Oerlikon Balzers can produce a multiple<br />
of workpieces without annoying<br />
burrs and grooves before the tool<br />
must be reground or repolished. Other<br />
advantages: less material removal in<br />
the regrinding process and a longer<br />
useful life.<br />
Cost factor: longevity<br />
BALINIT ® coatings prevent adhesion<br />
and cold welding. Because of the<br />
reduced friction, the tool surfaces are<br />
exposed to less thermal stress, which<br />
prevents crack-inducing surface fatigue.<br />
The result: BALINIT ® -coated<br />
tools have clearly longer service lives.<br />
Cost factor: tool failure<br />
Depending on the tool load and the<br />
number of load changes, tools can fail<br />
prematurely due to material fatigue.<br />
Experience shows that BALINIT ® -coated<br />
tools are exposed to less stress<br />
because of the lower coefficient of<br />
friction and reduced susceptibility to<br />
cold welding. Your benefit: less scrap<br />
and machine downtime.<br />
uncoated BALINIT ® C<br />
Tool costs (EUR) 3,445 4,065<br />
Tool life (parts) 50,000 89,600<br />
Tool costs per part (EUR) 0.07 0.05<br />
Yield per min. (parts)<br />
Production costs per min. (EUR)<br />
28 38<br />
(incl. wage costs and depreciation) 3.84 3.84<br />
Production costs per part (EUR) 0.14 0.10<br />
Machine downtime per part (EUR) 0.03 0.00<br />
Subsequent machining per part (EUR) 0.04 0.00<br />
Additional costs per part (EUR) 0.07 0.00<br />
Total production costs per part (EUR) 0.28 0.15<br />
Savings in % 46<br />
In the production of hinges for Volvo tailgates, unit<br />
costs were reduced by 46 % as a result of higher cycle<br />
frequencies, the elimination of tool changes and<br />
subsequent machining, and the longer life of BALINIT ® -<br />
coated tools.<br />
Cost factor: lubricants<br />
Conventional punching and forming<br />
presses consume large amounts of<br />
lubricant. In many cases, low-friction<br />
BALINIT ® coatings reduce the amount<br />
of lubricant needed. Under certain circumstances,<br />
they even allow a switch<br />
to dry processes. Whatever the case<br />
may be: you will see a substantial reduction<br />
in lubricant costs.<br />
Cost factor: quality<br />
BALINIT ® -coated tools prevent cold<br />
welding and fretting, which noticeably<br />
improves the surface quality of the<br />
workpieces. In the real world, this<br />
means a significant reduction of scrap<br />
and subsequent machining effort.<br />
03
You save even more in production<br />
With its positive coating properties<br />
and the high coating quality, BALINIT ®<br />
boosts productivity in punching and<br />
forming.<br />
Productivity factor: service life<br />
The extreme hardness of the BALINIT ®<br />
coating effectively protects tools<br />
against abrasive wear and prevents<br />
dimensional changes of the functional<br />
surfaces. Moreover, coated punches<br />
can be reground more frequently due<br />
to less flank wear and are therefore<br />
reusable for a longer period<br />
of time.<br />
Productivity factor:<br />
cycle frequencies<br />
BALINIT ® -coated tools are more resistant<br />
to wear and cold welding. Users<br />
benefit from these coating properties<br />
and operate their machines at higher<br />
stroke rates. The result: improved yield,<br />
greater productivity.<br />
Productivity factor:<br />
capacity utilisation<br />
Tools have a decisive impact on the<br />
economics of punching and forming.<br />
BALINIT ® increases performance and<br />
production safety and thus reduces<br />
the downtime of manufacturing equipment.<br />
04<br />
Productivity factor:<br />
forming process<br />
The high wear resistance and good<br />
sliding properties of BALINIT ® coatings<br />
have a beneficial effect on the forming<br />
process. Further advantages: higher<br />
dimensional accuracy across a longer<br />
tool life, fewer drawing stages, readyto-install<br />
workpieces with minimal<br />
subsequent machining.<br />
Punching<br />
Parts produced [1,000 units]<br />
200<br />
160<br />
120<br />
80<br />
40<br />
0<br />
TiN<br />
BALINIT ®<br />
ALCRONA<br />
Tool: Carbide piercing punch, Ø 3.6 mm<br />
Workpiece: DIN 1.0213 (C8C)<br />
Process: Piercing of through hole<br />
with lubrication<br />
Advantage: Up to 300 % longer tool life,<br />
thus lower unit costs<br />
Source: SFS Intec AG<br />
Heerbrugg (Switzerland)
You can establish higher manufacturing standards<br />
BALINIT ® -coated tools stay in shape<br />
longer and produce top-notch workpieces<br />
– with finer surfaces and<br />
cut edges.<br />
Quality factor: surface<br />
The forming process produces high<br />
surface loads and friction-induced<br />
heat build-up. This has a negative impact<br />
on the effectiveness of lubricants.<br />
Microwelds can occur and in turn<br />
produce grooves and rough cuts. The<br />
tool has to be prematurely remachined<br />
or replaced.<br />
A BALINIT ® coating perceptibly increases<br />
surface and cut qualities. This<br />
is important particularly for workpieces<br />
that need to look perfect.<br />
Fine Blanking<br />
Tool life [million parts]<br />
7<br />
6<br />
5<br />
4<br />
3<br />
2<br />
1<br />
0<br />
120,000<br />
6,300,000<br />
Quality factor:<br />
dimensional accuracy<br />
BALINIT ® -coated tools make it possible<br />
to produce workpieces with tighter<br />
manufacturing tolerances and improved<br />
dimensional accuracy. Depending on<br />
requirements, the result is ready-toinstall<br />
workpieces or components that<br />
need only very little finishing work.<br />
Quality factor: cleanliness<br />
BALINIT ® cuts lubricant consumption<br />
so that the workpiece cleaning effort<br />
is considerably reduced. Cleaning can<br />
even be eliminated entirely in dry processes<br />
– a must in production for food<br />
and pharmaceutical applications.<br />
Workpiece surface roughness Ra [µm]<br />
BALINIT ®<br />
uncoated BALINIT ®<br />
uncoated<br />
Process: Fine blanking with BALINIT ® -coated tools<br />
Service life increase factor: 52.5<br />
Regrinding: Uncoated: after 20,000 parts<br />
Coated: after 300,000 parts<br />
Number of times regrinding is possible: Uncoated: 5<br />
Coated: 20<br />
3.45<br />
0.12<br />
4<br />
3<br />
2<br />
1<br />
0<br />
BALINIT ® -coated drawing dies for the production of<br />
wheel suspension system collars remain in service more<br />
than 10 times longer.<br />
05
You conserve resources and<br />
spend less on consumables<br />
Using BALINIT ® coatings, Renault tripled the life of<br />
a clutch fork forming tool and dramatically reduced<br />
lubricant consumption.<br />
Sheet metal forming<br />
06<br />
Oil consumption per month [litres]<br />
8,000<br />
7,000<br />
6,000<br />
5,000<br />
300<br />
200<br />
100<br />
0<br />
7,000<br />
uncoated<br />
50<br />
BALINIT ®<br />
BALINIT ® -coated tools are environmentally<br />
friendly: because they will run<br />
with smaller amounts of less problematic<br />
lubricants and help conserve<br />
resources.<br />
Ecology factor:<br />
lubricant metering<br />
BALINIT ® assures the reliable separation<br />
of workpiece and tool. Even<br />
under adverse lubrication conditions,<br />
the result is a safe and defined set of<br />
operating parameters. The options for<br />
environmentally friendlier production<br />
range from smaller lubricant quantities<br />
to dry production.<br />
Ecology factor: lubricant choice<br />
When BALINIT ® -coated tools are<br />
deployed, you can work with ecologically<br />
safer lubricants. This not only<br />
reduces the effort and cost involved<br />
in reconditioning but also makes your<br />
eco-balance look good.<br />
Ecology factor: resources<br />
BALINIT ® boosts the life of your tools<br />
by several orders of magnitude. At<br />
the same time, less scrap is produced<br />
with coated tools. This sustainably cuts<br />
consumption of valuable resources.
Coating properties and<br />
application recommendations at a glance<br />
Properties of BALINIT ® coatings<br />
BALINIT ® B BALINIT ® BALINIT ® BALINIT ® D BALINIT ® BALINIT ® BALINIT ® C BALINIT ®<br />
FUTURA HARDLUBE LUMENA ALCRONA TRITON<br />
NANO<br />
Coating material TiCN TiAlN TiAlN +WC/C CrN TiAlN AlCrN WC/C DLC<br />
(Me-C:H) (a-C:H)<br />
Microhardness (HV 0.05) 3,000 3,300 3,0001) Coefficient of<br />
1,750 3,400 3,200 1,000 - 1,500 >2,500<br />
friction against steel (dry) 0.4 0.30 - 0.35 0.15 - 0.20 0.5 0.30 - 0.35 0.35 0.1 - 0.2 0.1 - 0.2<br />
Coating thickness (μm) as appropriate to application<br />
Residual compressive stress (GPa)<br />
Maximum<br />
-4.0 -1.3 / -1.5 -1.7 / -2.0 -1.5 / -2.0 -1.1 -3.0 -1.0<br />
service temperature (°C) 400 900 8001) 700 900 1,100 300 350<br />
Coating temperature (°C) 450 200 - 450 450 200 - 450 450 1100 N/mm2 F, AC F, AC L, AC L, AC<br />
Stainless steel HL, AC+C HL, AC+C HL, AC+C HL, AC+C L, AC<br />
Titan-alloys F F L F L, AC<br />
Aluminium-alloys HL, T HL, T HL, AC+C HL, AC+C L, AC<br />
Copper, Brass, Bronze F, AC F, AC D, AC D, AC D, AC<br />
Zinced sheets F, AC F, AC HL, AC+C L, AC<br />
B = BALINIT ® B L = BALINIT ® LUMENA<br />
D = BALINIT ® D AC = BALINIT ® ALCRONA<br />
C = BALINIT ® C HL = BALINIT ® HARDLUBE<br />
F = BALINIT ® FUTURA NANO T = BALINIT ® TRITON<br />
07
We are at your service. World-wide.<br />
Headquarters<br />
OC Oerlikon Balzers AG<br />
Oerlikon Balzers Headquarters<br />
Iramali 18<br />
LI-9496 Balzers<br />
Liechtenstein<br />
Tel +423 388 7500<br />
www.oerlikon.com/balzers<br />
Argentina<br />
Oerlikon Balzers Revestimentos<br />
Metálicos Ltda<br />
Av. Pablo Richieri, 4240<br />
Córdoba 5014<br />
Tel +54 351 464-8999<br />
www.oerlikon.com/balzers/ar<br />
Benelux<br />
Oerlikon Balzers Coating Benelux NV<br />
Schurhovenveld 4 050<br />
B-3800 Sint-Truiden<br />
Tel +32 11 69 30 40<br />
www.oerlikon.com/balzers/be<br />
Brasil<br />
Oerlikon Balzers Revestimentos<br />
Metálicos Ltda<br />
Rua Balzers, 250<br />
Parque Industrial – Jundiai-SP<br />
13213-084<br />
Tel +55 11 2152 0464<br />
www.oerlikon.com/balzers/br<br />
Canada<br />
Oerlikon Balzers Coating USA Inc.<br />
3250 Harvester Road<br />
Burlington, Ontario L7N 3W9<br />
Tel +1 905 631 7094<br />
www.oerlikon.com/balzers/us<br />
China<br />
Oerlikon Balzers Coating<br />
(Suzhou) Co., Ltd<br />
No.9 Chang Yang Street<br />
Suzhou Industry Park<br />
Suzhou, 215024<br />
Jiangsu Province, China<br />
Tel +86 512 676 20369<br />
www.oerlikon.com/balzers/cn<br />
Česká Republika<br />
Oerlikon Balzers Coating Austria GmbH<br />
organizační slozˇka<br />
Červeny´ Krˇízˇ 250<br />
586 02 Jihlava<br />
Czech Republic<br />
Tel +420 561 201 500<br />
www.oerlikon.com/balzers/cz<br />
Deutschland<br />
Oerlikon Balzers Coating<br />
Germany GmbH<br />
Am Ockenheimer Graben 41<br />
D-55411 Bingen<br />
Tel +49 67 21 7 93-0<br />
www.oerlikon.com/balzers/de<br />
Oerlikon Balzers VST GmbH & Co. KG<br />
Hohe-Flum-Straße 22<br />
D-79650 Schopfheim<br />
Tel +49 7622 3999 0<br />
www.oerlikon.com/balzers/vst<br />
España<br />
Oerlikon Balzers-Elay Coating S.A.<br />
Antigua, 2<br />
E-20577 Antzuola<br />
Tel +34 9 43766208<br />
www.oerlikon.com/balzers/es<br />
France<br />
Oerlikon Balzers Coating France SAS<br />
4 rue Louis de Broglie<br />
Parc d´Activités de l´Esplanade<br />
Saint Thibault des Vignes<br />
F-77462 Lagny-sur-Marne Cedex<br />
Tel +33 1 6412 49 00<br />
www.oerlikon.com/balzers/fr<br />
India<br />
Oerlikon Balzers Coating India Ltd.<br />
EL-22, J Block<br />
M.I.D.C. Bhosari<br />
Pune 411 026<br />
Tel +91 20 3061 6000<br />
www.oerlikon.com/balzers/in<br />
Italia<br />
Oerlikon Balzers Italy S.p.A.<br />
Via Volturno, 37<br />
I-20047 Brugherio (MI)<br />
Tel +39 039 28 9901<br />
www.oerlikon.com/balzers/it<br />
Korea<br />
Oerlikon Balzers Coating Korea Co., Ltd.<br />
Eyon-Hansan Industrial Park (5B-3, 4, 5)<br />
833-2 Hansan-ri Chongbuk-myeon<br />
Gyeonggi-do<br />
Pyongtaek City 451-833<br />
Tel +82 31 680 9900<br />
www.oerlikon.com/balzers/kr<br />
Liechtenstein<br />
OC Oerlikon Balzers AG<br />
Beschichtungszentrum<br />
Iramali 18<br />
LI-9496 Balzers<br />
Tel +423 388 5701<br />
www.oerlikon.com/balzers/ch<br />
Magyarország<br />
Oerlikon Balzers Coating Austria GmbH<br />
Magyarországi Fióktelepe<br />
Babér U. 6 (Alpa Ipari Zóna)<br />
H-8000 Székesfehérvár<br />
Tel +36 22 506-631<br />
www.oerlikon.com/balzers/hu<br />
México<br />
Oerlikon Balzers Coating México,<br />
S.A. de C.V.<br />
Acceso III No. 304 y 306<br />
Colonia Industrial La Montaña<br />
C.P. 76150<br />
Querétaro, Qro.<br />
Tel +52 442 209 68 00<br />
www.oerlikon.com/balzers/mx<br />
Nippon<br />
Oerlikon Nihon Balzers Coating Co., Ltd.<br />
7-2-2 Shinomiya, Hiratsuka-City,<br />
Kanagawa-Pref., Japan 254-0014<br />
Tel +81 463 54-2220<br />
www.oerlikon.com/balzers/jp<br />
Nordic Countries<br />
Oerlikon Balzers Sandvik Coating AB<br />
Årstaängsvägen 31 D-E<br />
SE-117 43 Stockholm<br />
Tel +46 8 681 4140<br />
www.oerlikon.com/balzers/se<br />
Österreich<br />
Oerlikon Balzers Coating Austria GmbH<br />
Burgstallweg 27<br />
A-8605 Kapfenberg<br />
Tel +43 38 62 34144<br />
www.oerlikon.com/balzers/at<br />
Polska<br />
Oerlikon Balzers Coating<br />
Poland Sp. z o.o.<br />
ul. Fabryczna 4<br />
PL-59-101 Polkowice<br />
Tel +48 76 746 48 00<br />
www.oerlikon.com/balzers/pl<br />
Portugal<br />
Oerlikon Balzers-Elay Coating S.A.<br />
sucursal em Portugal<br />
Zona Industrial do Casal da Areia,<br />
Lote 17<br />
PT-2460-392 Alcobaça<br />
Tel +351 262 544 663<br />
www.oerlikon.com/balzers/pt<br />
Romania<br />
S.C. Oerlikon Balzers Coating<br />
Austria GmbH Kapfenberg<br />
Austria - Maracineni Branch Office<br />
Platforma "Europa 2"<br />
sat Argeselu, nr. 537 bis - Hala 5<br />
Com. Maracineni<br />
Jud Arges - Romania<br />
RO-110195 Pidesti<br />
Tel +40 372 706 819<br />
www.oerlikon.com/balzers/ro<br />
Schweiz/Suisse<br />
Oerlikon Balzers Coating SA, Brügg<br />
Erlenstrasse 39<br />
CH-2555 Brügg<br />
Tel +41 323 65 74 74<br />
www.oerlikon.com/balzers/ch<br />
Singapore<br />
Oerlikon Balzers Coating<br />
Singapore Pte. Ltd.<br />
21 Kian Teck Drive<br />
Singapore 628838<br />
Tel +65 62 68 62 27<br />
www.oerlikon.com/balzers/sg<br />
Thailand<br />
Oerlikon Balzers Coating<br />
(Thailand) Co., Ltd.<br />
Amata Nakorn Industrial Estate<br />
700/38 Moo 6, T. Nongmaidaeng<br />
A. Muang Chonburi 20000<br />
Thailand<br />
Tel +66 38 468 810/-813<br />
www. oerlikon.com/balzers<br />
Türkiye<br />
Oerlikon Balzers<br />
Kaplama Sanayi ve Ticaret Ltd. Sti<br />
Nosab 120. Sokak No. 7<br />
16140 Nilüfer Bursa / Turkey<br />
Tel +90 224 411 00 77<br />
www.oerlikon.com/balzers/tr<br />
United Kingdom<br />
Oerlikon Balzers Coating UK Ltd.<br />
Bradbourne Drive, Tilbrook,<br />
Milton Keynes, MK7 8AT<br />
Great Britain<br />
Tel +44 19 08 37 72 77<br />
www.oerlikon.com/balzers/uk<br />
USA<br />
Oerlikon Balzers Coating USA, Inc.<br />
2511 Technology Drive<br />
Suite 114<br />
Elgin, IL 60124<br />
United States<br />
Tel +1 847 844-1753<br />
www.oerlikon.com/balzers/us<br />
www.oerlikon.com/balzers<br />
(0803)<br />
08 HQ043EN
Change language