Duty Exemption Scheme

C111
p)Welding flux 8.0 kgs
q)Weld wire 4.0 kgs
r)Surface protection film 13.3 kgs
s)Copper lined mould for casting 0.013 kg
t) Refractory Bricks/ Shapes 9 kgs
and/or Dead Burnt/ Sea Water/
Fused Magnesia for Captive use
for manufacture of Bricks/
Shapes
u) Monolithic Refractory Viz. 5 kgs
Castable, Gunning Mass &
Ramming Mass and/ or Dead
Burnt/ Sea Water/ Fused
Magnesia for captive use for
manufacture of Monolithic
Refractory
v) Special Refractories namely, 1 kg
Continuous Cast refractories
(such as Shrouds, Mono Block
Stoppers and Sub-entry Nozzles),
Slide Gate refractories, Porous
Plug Zircon/ Zirconia Nozzles
and Tundish Nozzles
Note 1.The above norm is applicable only if the export product(s) is manufactured through Blast Furnace-
LD Converter/ Open Hearth/ Energy Optimising Furnace routes in the integrated steel plants.
2. Ferro Niobium and Ferro vanadium would be permitted only if the alloying element namely Niobium
and Vanadium is present in the export product.
3. Item of import at Sl.No.1 (ii), 3(ii)(b)(i)(l) (p) (q)(s) and continuous cast refractories and Tundish
Nozzles at (v) shall not allowed in case of export of Steel ingots.
4. Item of import at Sl.No.1 (ii), 3(ii), (c), (m) & 3 (iii) (a), (b), shall not be allowed in case of rolled blooms/
billets/ slabs. However, against export of rolled billets made through continuous cast blooms, continuous
cast refractories & Tundish Nozzles under 3(ii)(v) shall be allowed.
5. Item of import at Sl.No.3 (ii) (p) and (q) shall be allowed in case of export of pipes and tubes only. The
item of import at Sl. No 3 (ii) (r) shall be allowed in case of export of CRGO/CRNGO sheets.
6.The item NonAlloy Steel Melting Scrap will be allowed as per the definition given in section XV of
Customs Tariff.
7.The item at Sl. No. 3 (ii)(s) shall not be allowed in case of import of item at Sl.No.1 (ii). Similarly, in case
of import of item at Sl.No. 1 (ii), the item at Sl.No.3 (ii) (s) will not be allowed.
C513 Non-alloy Steel bars &
rods (including Rounds,
Flats, Hexagons,
Octagons, Wire Rods,
Cold Twisted Bars,
thermo mechanically
treated reinforcing bars),
Angles, Shapes &
Sections (including
beams, joist, channels,
special profiles etc.) and
Rails
C514 Non-Alloy Steel Bars &
Rods (including Rounds,
Flats, Hexagons,
Octagons, Wire Rods,
Cold Twisted deformed
bars,
1000 kgs. 1 Non Alloy steel Ingots
OR
1070 kg
Non Alloy Steel Blooms/ Billets 1050 kg
OR
Non-alloy Steel Re-rollable
Scrap as per IS: 2549-1994
1070 kg
2 Rolls for rolling mills 1.77 kg
3 Furnace oil for oil fired reheating 50 kg
furnace in rolling mill
4 Saw/ Shear blade 0.01 kg
1000 kgs 1 a)Copper Scrap/Copper
Cathode/Copper Wire
Bar/Copper Rod (If copper is
present in the export product)
b)Cored Wires of Lead/ Lead
Shots (in case of export of lead
bearing free cutting steel only)
0.04 kg
2.5 kg