CATERPILLAR

More documents

Recommendations

Info

Uninstall Instructions for SIS Windows 2002B or earlier Note: uninstalling a version of SIS Windows after a version of SIS DVD has been installed will corrupt the DvJu plug-in. It is recommended and you uninstall SIS Windows immediately before updating or installing SIS DVD 2006A. Step 1 Close all other programs running under Windows including any antivirus software. Step 2 Navigate to the Control Panel, and choose Add/Remove Programs. Step 3 Select “Service Information System” and click the “Change/Remove” button. Step 4 Click “Yes” to confirm the deletion. Step 5 Follow the steps in the uninstall wizard and reboot the computer. 82
Service Information System Web (SIS Web) Purpose Like SIS DVD, SIS Web allows you to access parts and service information on all Caterpillar products shipped since 1977. The data contains more information types and is up to 12 weeks more current than DVD data. Installation To access SIS Web, you need access to the internet, a CWS user ID, and SIS Web user. Contact your SIS Coordinator or SIS Administrator for help. To access SIS Web through STW, you need to install or upgrade to STW 2003B or later. SIS Web was added as an option to the list of applications that can be installed by STW. If you are installing STW for the first time or doing an "add/remove" of applications, check the SIS Web option when selecting applications to be installed. If you are doing an "update," SIS Web will be automatically installed. Operation To launch SIS Web within STW, click on the SIS icon on the STW launchpad. The same icon in the STW launchpad will launch both SIS Windows and SIS Web. A preference setting in STW determines which application will be launched. To change the SIS application preference setting in STW: Step 1 From the STW home page, click the "View" menu option, and select "Preferences...". Illustration 64: Service Technician Workbench Home dialog box Step 2 Click on the "SIS Preference" tab. Step 3 Select the “Connected” radio button in the “Configuration” section. Step 4 Click the "Apply" button and then click the "OK" button on the dialog telling you to shut down STW. Step 5 Click the "OK" button on the "View Preferences" dialog, and restart STW. Be sure to also restart SIS. If the SIS icon is in the system tray, click on it, and choose “Shutdown & Exit” before restarting STW. 83
Page 1 and 2:
1 CATERPILLAR Service Technician Wo
Page 3 and 4:
Table of Contents Introduction.....
Page 5 and 6:
Installation.......................
Page 7 and 8:
Computer/Software Hardware Recommen
Page 9 and 10:
If you do not have Service Technici
Page 11 and 12:
Illustration 4: The STW setup will
Page 13 and 14:
Select the “Yes” button to cont
Page 15 and 16:
Step 8 Select Components The Select
Page 17 and 18:
Frequently Asked Questions If you a
Page 19 and 20:
Q) How do I subscribe to SIS and/or
Page 21 and 22:
Purpose If communicating Service In
Page 23 and 24:
- OR - 7X-1700 - Caterpillar Commun
Page 25 and 26:
Instructions To set up the Communic
Page 27 and 28:
The service tool will remain unaffe
Page 29 and 30:
202 A required INI file was not loc
Page 31 and 32: Challenger Technician Purpose The C
Page 33 and 34: Dataview DataView measures and logs
Page 35 and 36: • To Delete Existing Lines from a
Page 37 and 38: MNTWOCTL (Direct Labor to Approval
Page 39 and 40: Illustration 14: Enter the intended
Page 41 and 42: Illustration 16: A question mark ca
Page 43 and 44: Illustration 19: Other shift time e
Page 45 and 46: Illustration 22: Enter the appropri
Page 47 and 48: Labor Approval Setup - DBS DBS must
Page 49 and 50: Labor Upload -End of Job Setup Illu
Page 51 and 52: Illustration 29: Open the SIMS DBS
Page 53 and 54: Illustration 32: Save the report te
Page 55 and 56: Select the Upload Settings Tab and
Page 57 and 58: Example of file name and save: AA00
Page 59 and 60: 1-877-598-8920 DCS Support Center:
Page 61 and 62: 1. Run the SIS Setup CD on the netw
Page 63 and 64: o Select the TA inspection to open.
Page 65 and 66: � � Illustration 43: TA Search
Page 67 and 68: o o Illustration 46: The TA Navigat
Page 69 and 70: o Following are items and their bac
Page 71 and 72: Step 9 On the STW installation main
Page 73 and 74: Step 12 In the Software License Agr
Page 75 and 76: Step 15 After the files have been c
Page 77 and 78: Illustration 57: Program Maintenanc
Page 79 and 80: Step 17 After the files have been c
Page 81: Illustration 63: Monthly Data Updat
Page 85 and 86: Parts Integrator Purpose Parts Inte
Page 87 and 88: - The integration software has been
Page 89 and 90: Illustration 74: Step 8 Once the
Page 91: Refer to the STW Knowledge Entry li
show all

CATERPILLAR

Create successful ePaper yourself

Delete template?

Save as template?